PURPOSES : This study compared the performance evaluation of a hot mix asphalt (HMA) and asphalt mixture of a warm-antistrip agent. METHODS : A mix design applying Korean standards was conducted to evaluate the performance evaluation. Thereafter, the quality standard evaluation of the asphalt mixture produced was conducted, and if all quality standards were satisfied, a performance evaluation was conducted. Types of performance evaluation included the Hamburg wheel tracking test and dynamic modulus test. RESULTS : As a result of the Hamburg wheel tracking test, the asphalt mixture with a warm-antistrip agent obtained a lower sedimentation value at 10000 times and 20000 times. This result is considered to have higher plastic deformation resistance of the asphalt mixture with a Warm-antistrip agent than HMA. The U.S. Department of Transportation stipulates that plastic deformation resistance is excellent if the asphalt mixture does not exceed 20,000 times the precipitate of 20 mm. Therefore, we confirmed that the plastic deformation resistance of the asphalt mixture with a warm-antistrip agent was excellent. Additionally, the master curve was analyzed by synthesizing the results of the dynamic modulus test. When analyzing the low load cycle at the bottom left of the master curve, the dynamic modulus value of the master curve was higher in the asphalt mixture with a warm-antistrip agent than in the HMA. In addition, when analyzing the high load cycle part, the dynamic modulus of the HMA was measured to be higher than that of the asphalt mixture with a warm-antistrip agent. Accordingly, the resistance to fatigue cracking of the asphalt mixture with a warm-antistrip agent was considered superior to that of the HMA. CONCLUSIONS : As a result, we confirmed that the asphalt mixture with a warm-antistrip agent that satisfies the Korean quality standards had better plastic deformation and fatigue resistance for all performance evaluation tests conducted in this study than the HMA. However, since the Hamburg wheel tracking test did not significantly differ in the amount of sedimentation in the performance evaluation tests and the mixture using one additive was compared with HMA, studies on the effects of various additives containing warm-antistrip agents are required.

PURPOSES : The logistic roads for freight transport along to the new port of Busan have been suffered by the rapid weather changes including high temperature and torrential rain. As a result, the roads require annual repair, which have been distressed seriously by the heavy logistic and environmental loads. Therefore, we need to identify the cause of the road pavement distresses and find a proper design method to minimize the pavement distress in order to prohibit the problem aggravated. METHODS : The damaged conditions of the logistic roads were investigated on-site. In addition, applied pavement designs, real traffic volumes, and historical climatic information were intensively collected for this project. With the investigated and collected data Korean pavement design program (KPRP) was implemented to analyzed the causes of the damaged roads and conceive the pavement design draft optimized for the roads. RESULTS : According to the investigation and KPRP analysis, the traffic volume to transport freights impacts significantly the pavement distress, so that a higher PG grade binder type should be used, for which polymer modified asphalt (PMA) binders are recommended. Moreover, its pavement thickness should be increased to secure load bearing capacity, but thickening the pavement has been discouraged due to difficulties induced by the road-sectional change, especially road-height change. CONCLUSIONS : In conclusion, 5cm PMA overlay is suggested for the normal-scale maintenance, and 7cm PMA overlay for large-scale maintenance. Besides these, the application of Polymer-modified Stone Matrix Asphalt (PSMA) using PG76-22 binder would be the best preventive maintenance method, which has been well know as having higher fatigue resistant performance than general PMA. However, if we use PSMA, quality control should be very cautious since PSMA can be very susceptible premature distress if its production and construction are improperly proceeded.

PURPOSES : The purpose of this study is to identify a gradation control method that minimizes the volatility of recycled aggregates to maintain the quality of reclaimed asphalt mixtures. METHODS : In this study, two types (0~13 and 0~10 mm) of recycled aggregate stockpiles with an extraction viscosity of 40,000 poise and a 19 mm hot asphalt mixture with virgin aggregates are used. The test methods are evaluated for plastic deformation resistance using the Hamburg wheel-tracking test and for low-temperature crack resistance using the dynamic modulus test. In the field, the performance is evaluated via an accelerated pavement test. RESULTS : The Hamburg wheel-tracking test shows good water resistance as well as less than 5 mm of deformation. The result of a dynamic modulus test at -5 °C shows a 92.9% low-temperature crack resistance as compared with that of the 19 mm dense grade hot-mix asphalt mixture. The result of the accelerated pavement test confirms that the performances of the 19 mm dense grade hot-mix asphalt mixture and reclaimed asphalt mixture are equal owing a 1.2 cm plastic deformation. CONCLUSIONS : By evaluating the plastic deformation resistance and crack resistance of the reclaimed asphalt mixture based on a stockpile gradation controlled at 0~10 mm via an indoor test, it is discovered that the plastic deformation resistance increases partially, whereas the crack resistance remains almost unchanged. The accelerated pavement test confirms that a performance equivalent to that of a 19 mm dense grade hot-mix asphalt mixture is achieved.

PURPOSES : In a previous study, an error was detected in data pertaining to the direction and velocity of a roller. Hence, in this study, the correlation between these two variables and acceleration data is analyzed. Relevant algorithms are developed by adding variables to existing algorithms. METHODS : A tachometer and GPS are used to acquire the velocity, compaction direction of rollers, and number of compactions. Subsequently, data input to an accelerometer are compared and analyzed. RESULTS : Based on FFT analysis, it is discovered that the data are inaccurate when a forward reverse is performed. Using the GPS, the velocity of the roller is differentiated based on the number of pledges, and then added as a variable to the algorithm. Subsequently, it is evaluated and analyzed only with data during forward movement based on changes in the latitude and longitude. CONCLUSIONS : It is discovered that the acceleration data values from both the left and right rollers differ owing to their weight difference, as indicated by the asphalt gradient. Data changes based on asphalt gradients are analyzed using gyro sensors. If the correlation between the two sets of data is high, then the algorithm is advanced by introducing a cross spectrum after calibrating the acceleration value based on the gradient.

PURPOSES : This study proposes a method to automatically analyze the shape of asphalt concrete aggregate using computer image analysis technology. METHODS : To develop automatic aggregate shape analysis technology, we developed an aggregate shape boundary analysis algorithm that combines Watershed algorithm and morphology technology. After the algorithm was developed, it was mounted on a separate prototype and compared with the manual aggregate shape analysis method. RESULTS : As a result of the algorithm comparison, the accuracy of the aggregate shape analysis was about 90%, and there was a problem that some noise occurred. This problem was derived from external roughness, the shape of the overlapped aggregate, and sand as the main causes. Therefore, we devised a method to analyze the shape of the aggregate by adjusting the external illuminance constant or using an artificial intelligence model. CONCLUSIONS : The results of this study can be used as basic research data to help improve quality control techniques in the production of asphalt concrete in the future.

PURPOSES : Water content causes a big problem in terms of the quality and economy of the asphalt plant. However, the current guidelines do not suggest specific rules other than roof installation. Therefore, this study proposes a water content management index, QM, and management flow chart by analyzing the water content variability of the stockpile and cold bin aggregates and suggests a guideline rule for improving water content management, including stockpile floor inclination via analysis of slope stability. METHODS : To analyze the variability of water content in the asphalt plant, stockpile and cold bin aggregate samples were collected from the asphalt plant over two years and a water content lab test was conducted via sieve analysis. In addition, domestic and foreign water content management guidelines were compared and the economic effect was analyzed according to water content DB analysis for the importance of water content management. The influence factors of water content variability were also analyzed. To apply the 3σ quality management technique for the development of the water content management index, QM, a water content management limit and procedure was proposed through the asphalt mix design. RESULTS : As a result of analyzing the water content variability, it was found that the water content of the stockpile fine aggregates should be intensively managed immediately after the rainy season and the QM index developed in this study should be 1 or more. In addition, as a result of the stability analysis according to the change in the stockpile floor inclination, it was found that the safety factor was lowered according to the slope angle and floor inclination. CONCLUSIONS : In the past, a passive method of preventing rainwater with a roof was used for water content management and ambiguous qualitative rules were suggested in the guidelines. In this study, a procedure for managing the water content of asphalt plant aggregates using the QM index, a quantitative stock floor inclination chart, and rules for improving water content management were presented for the quality control of asphalt plant aggregates.

PURPOSES : The objective of this study is to address various problems, such as an increase in material cost and premature failure (e.g., cracks and potholes) of porous pavements, and to develop multifunctional asphalt and asphalt mixtures to ensure the long-term commonality of porous asphalt pavements. METHODS : A basic quality test of two types of porous asphalt mixtures was performed. One type consisted of the existing porous asphalt mixture, using domestically presented grading, and the other a porous asphalt mixture using high-viscosity modified asphalt with enhanced low-temperature properties, aimed at improving strain resistance and developed by applying the grading suggested by the Federal Highway Administration (FHWA). RESULTS : The cantabros loss rate was 19.62 % for conventional modified asphalt (PG 82-22) and 5.95 % for the developed highviscosity modified asphalt (PG 88-28), indicating that both mixtures passed the criteria. Regarding the drain-down loss rate, mixtures using both types of asphalt were found to pass all quality standards. The average permeability coefficients for each porous asphalt mixture were 0.023 and 0.018 and both types of porous asphalt mixtures satisfied the quality standard of 0.01 cm/s, as given by the Asphalt Concrete Pavement Guidelines of the Ministry of Land, Infrastructure, and Transport. CONCLUSIONS : As a result of the mix design of the two porous asphalt mixtures, the mixture developed in this study was found to be superior to the conventional porous asphalt mixture using conventional porous asphalt grading and modified asphalt.

PURPOSES : The use of reclaimed aggregate has been recently increasing with the increase in the amount of waste asphalt concrete. The application of these materials can reduce the properties of the asphalt pavement when compared with the case when recycled aggregate is not used. The objective of this study is to evaluate the performance of the asphalt mixtures with various mix ratios of reclaimed aggregate. METHODS : To measure the performance, the following tests using the mixtures prepared in accordance with the Korea Standards were conducted: Hamburg wheel-tracking test, third-scale model mobile loading simulator test, and dynamic modulus test. RESULTS : The test results of the Hamburg wheel-tracking test indicate that the water resistance was similar in each mixture and the plastic deformation resistance was good in the high-ratio reclaimed aggregate mixture. In the case of the third-scale model mobile loading simulator test, the plastic deformation demonstrated a high resistance in the high-ratio reclaimed aggregate mixture. The results were similar to those of the Hamburg wheel-tracking test; however, the cracking resistance was poor with a high recycled aggregate incorporation ratio. The dynamic modulus test results demonstrated excellent resistance to plastic deformation at a relatively high ratio of reclaimed aggregate admixture. The crack resistance was weakened when a high ratio of reclaimed aggregate mixture was used. CONCLUSIONS: As the reclaimed aggregate content increased, the plastic deformation resistance increased and the crack resistance decreased.

PURPOSES: The objective of this study is to evaluate the properties of eco-friendly waterproofing materials for bridge decks. METHODS: Various waterproofing materials and construction methods that are widely used in Korea were evaluated. Then, the problems in field application were identified. In order to solve these problems, it is necessary to improve constructability and stability. Thus, the properties of heating waterproofing membranes and waterproofing systems using recycling additives were evaluated. In addition, a field test was conducted to ensure the construct-ability and stability. RESULTS AND CONCLUSIONS : Waterproofing materials were developed using waste tires and carbon black the results of the softening point test, tensile adhesion test, and shear adhesion test. A new sheet system, which consists of mesh and vinyl, was also determined from the sheet test. The properties of waterproofing materials were better than those developed under the "A Asphalt Concrete Pavement Construction Guidelines" according to the results of laboratory tests and the report of the authorized testing agency. Finally, the field test showed that the materials met quality standards. In future research, it will be necessary to conduct continuous field tests and follow-up inspections.

PURPOSES : The objective of this study was to evaluate the field applicability of chip seals using recycled aggregates by comparing performance between natural aggregates and recycled aggregates for chip seals. METHODS : In order to check the performance of chip seals using recycled and natural aggregates, Bitumen Bond Strength (BBS) test, Vialit and bleeding tests were carried out. Cationic emulsions (RS(C)-2 and latex modified RS(C)-2L) were used in the tests. Granite aggregates were used as the natural aggregate and recycled aggregate from road wastes were used as the recycled aggregate. The aggregate was used with uniform gradation between 10 mm and 4.75 mm to clearly compare the performance difference between natural and recycled aggregates. RESULTS : Test results showed that the aggregate retention was low for both natural and recycled aggregates when applying RS(C)-2 (unmodified emulsion), but there was almost no difference between them when applying RS(C)-2L and RS(C)-2L-1 (modified emulsion) in the Vialit test results. In the bleeding tests, there was no bleeding for both natural and recycled aggregates when applying RS(C)-2 and RS(C)-2L. CONCLUSIONS: It was possible to apply chip seals using recycled aggregates in the field because the chip seals with recycled aggregates and RS(C)-2L (modified emulsion) showed aggregate retention similar to that of natural aggregates, and there was no bleeding.

PURPOSES :This study proposes standards for rural access road pavement section and thickness design considering existing access road construction conditions; the study also proposes a complementary policy that can be used for design convenience.METHODS:Various literature review and case studies had been performed in terms of rural access road section and thickness design, both domestically and internationally, and this was followed by domestic rural access road field surveys. KPRP and KENLAYER were used to analyze the commonalities and predict the remaining life. Data on real cost is used to select an appropriate construction method through economic analysis.RESULTS:The economic efficiency of concrete pavement (15×15) was the highest in terms of economic efficiency of performance life and traffic volume. In the case of asphalt pavement, it is considered that the most economical method is to implement micro-surfacing method four times as a preventive maintenance method (once every 10 years and 4.5 years for asphalt concrete pavement and MS construction method, respectively). Repairable asphalt pavement is advantageous for areas where heavy vehicles are expected to pass. In the case of other general areas, it is considered economical to place concrete (15×15) pavement. However, as analytical results on its performance life are unavailable, it is to be considered for study in the future.CONCLUSIONS :This study proposed interim design guidelines based on various domestic and international design guidelines and case studies. However, in order to develop the final design criteria applicable to the field, it is necessary to (a) estimate the bearing capacity of the lower level of the pavement at various sites, (b) estimate the daily traffic volume, (c) implement advanced low-cost pavement technologies, and (d) propose maintenance standards and techniques for long-term performance.

OBJECTIVES: The objective of this research is to develop additives for the modification of Solvent DeAsphalting Residue (SDAR) to be used as pavement materials, and evaluate the performance of asphalt mixture manufactured using the SDAR modified by developed additives. METHODS: The SDAR generally consists of more asphaltenes and less oil components compared to the conventional asphalt binder, and hence, the chemical/physical properties of SDAR are different from that of conventional asphalt binder. In this research, the additives are developed using the low molecular oil-based plasticizer to improve the properties of SDAR. First, the chemical property of two SDARs is analyzed using SARA (saturate, aromatic, resin, and asphaltene) method. The physical/rheological properties of SDARs and SDARs containing additives are also evaluated based on PG-grade method and dynamic shear-modulus master curve. Second, various laboratory tests are conducted for the asphalt mixture manufactured using the SDAR modified with additives. The laboratory tests conducted in this study include the mix design, compactibility analysis, indirect tensile test for moisture susceptibility, dynamic modulus test for rheological property, wheeltracking test for rutting performance, and direct tension fatigue test for cracking performance. RESULTS : The PG-grade of SDARs is higher than PG 76 in high temperature grades and immeasurable in low temperature grades. The dynamic shear modulus of SDARs is much higher than that of conventional asphalt, but the modified SDARs with additives show similar modulus compared to that of conventional asphalt. The moisture susceptibility of asphalt mixture with modified SDARs is good if, the antistripping agent is included. The performance (dynamic modulus, rutting resistance, and fatigue resistance) of asphalt mixture with modified SDARs is comparable to that of conventional asphalt mixture when appropriate amount of additives is added. CONCLUSIONS: The saturate component of SDARs is much less than that of conventional asphalt, and hence, it is too hard and brittle to be used as pavement materials. However, the modified SDARs with developed additives show comparable or better rheological/physical properties compared to that of conventional asphalt depending on the type of SDAR and the amount of additives used.

PURPOSES : The objective of this study was to evaluate the results of the dynamic immersion test (DIT) through digital image analysis (DIA). METHODS : The asphalt binder retained post DIT was inspected visually by more than three investigators. However, because visual observations can be subjective, depending on the inspector’s skills and knowledge, DIA was also performed. The threshold value for the DIA was determined by a mesh analysis, in which the digital image to be analyzed is divided into very small meshes. In addition, the bitumen bond strength (BBS) test was also performed to the compare the visual results with the mechanical values. RESULTS AND CONCLUSIONS : Depending on the materials used, various methods can be used to predict the behavior of retained asphalt. However, the increasing ratio in the trend of retained asphalt shows different behaviors among the evaluation methods. In this study, the results of the visual observations were significantly different from those of the DIA, the mesh analysis, and the BBS tests. Thus, DIA is an appropriate method for evaluating the results of the DIT. However, in order to use this technique in the field, it is necessary to determine a more reasonable threshold value by performing DIA on various materials.

PURPOSES: The objective of this paper is to understand the deterioration phenomenon and causes in the pavement of a ramp area. METHODS: Ramp areas need to be sloped because of the centrifugal force, which depends on the vehicle speed and grade of the ramp area. As a result, vertical and horizontal forces are applied on the pavement surface of the ramp area. Furthermore, the horizontal force depends on the vehicle speed and grade of the ramp area. In order to analyze the pavement structure of a ramp area, a multi-layered elastic analysis program was used to evaluate the weakest link of fatigue cracking deterioration, according to the simultaneously applied vertical and horizontal forces. RESULTS : From case studies related to the bonding conditions between the surface and base layer in a ramp area, it was found that the partially bonded cases resulted in a critical potential of fatigue cracking deterioration, in a comparison of 50%, 70%, and fully bonded cases. CONCLUSIONS : According to the results of the case studies, the pavement structure system should be reinforced by upgrading the material or increasing the thickness compared to the general pavement areas, in order to provide a performance life similar to the mainline pavements in the ramp areas.

PURPOSES: The objective of this study is to investigate the properties of recycled asphalt binders with five different rejuvenators, in order to evaluate the applicability of the recycled asphalt binders compared with the original asphalt binder. METHODS: In order to simulate recycled asphalt binders, fresh asphalt binders are aged by various Superpave aging procedures, such as the rolling thin-film oven (RTFO) and the pressure aging vessel (PAV). Then, selected rejuvenators are added to the aged asphalt binders in the amount of 5%, 10%, and 15%. The asphalt binder properties are evaluated by the dynamic shear rheometer (DSR), the rotational viscometer (RV), and the bending beam rheometer (BBR). In this study, AP-5 (penetration grade 60-80, PG 64-16) asphalt binder is used. A total of five types of rejuvenators are employed. RESULTS AND CONCLUSIONS : When considering aged asphalt without a new asphalt binder, it seems that the percentage of rejuvenator used in Korea is a bit too low, and that it fails to possess the characteristics of the original binder. From the current practice of evaluating the properties of recycled binder based on penetration ratio only, the amount of rejuvenator required is similar for the long-term-aged binder, but is excessive for the longest-term aged binder, causing deterioration of workability and stiffness of the recycled binder.

PURPOSES : The objective of this study is to evaluate the SDAR (solvent deasphaltene residue), which is obtained from the solvent deasphalting (SDA) process, as a pavement material. METHODS : The physical properties of the SDAR were evaluated based on its chemical composition, and asphalt mixtures with the SDAR were fabricated and used for the evaluation of mechanical properties. Firstly, the chemical composition of SARA (saturate, aromatic, resin and asphaltene) was analyzed using the TLC-FID (thin-layer chromatography-flame ionization detector). Moreover, the basic material properties of the asphalt binder with the SDAR were evaluated by the penetration test, softening point test, ductility test, and PG (performance grade) grade test. The rheological properties of the asphalt binder with the SDAR were evaluated by the dynamic shear modulus (G*) obtained using the time-temperature superposition (TTS) principle. Secondly, the mechanical properties of the asphalt mixtures with the SDAR were evaluated. The compactibility was evaluated using the gyratory compacter. Moreover, the tensile strength ratio (TSR) was used for evaluating the moisture susceptibility of the asphalt mixtures (i.e., susceptibility to pothole damage). The dynamic modulus E*, which is a fundamental property of the asphalt mixture, obtained at different temperatures and loading cycles, was used to evaluate the mechanical properties of the asphalt mixtures. RESULTS AND CONCLUSION : The SDAR shows stiffer and more brittle behavior than the conventional asphalt binder. As the application of the SDAR directly in the field may cause early failures, such as cracks on pavements, it should be applied with modifiers that can favorably modify the brittleness property of the SDAR. Therefore, if appropriate additives are applied on the SDAR, it can be used as a pavement material because of its low cost and strong resistance to rutting.

PURPOSES: The objectives of this study were to develop a new polymer-modified emulsion for application to tack coats and to evaluate its properties by comparing it with other types of asphalt emulsions, with the goal of providing an enhanced tack coat material for use in construction. METHODS: Modified asphalt binders were developed from using SBS and SBR latex in the laboratory, and their fundamental properties, such as their penetration index and PG grade, were evaluated. Based on the properties, a new tack coat material was developed. To evaluate the newly developed asphalt emulsion, the bonding strength between the two layers of HMA was measured by applying a uniaxial tensile test and shear test. For the tests, a total of four different conditions were applied to the specimens, including the developed asphalt emulsion, latex modified asphalt emulsion, conventional asphalt emulsion, and non-tack coating. RESULTSAND CONCLUSIONS: Overall, the developed asphalt emulsion exhibits the best bonding strength behavior among all of the three types. Also, the two types of polymer-modified emulsions were found to be better for application for use as a tack coat than a conventional emulsion. Especially, at a high temperature (50℃), the conventional asphalt emulsion no longer acts as a tack coating material. Therefore, the polymer-modified emulsion should be considered for application to tack coat construction during the summer.