PURPOSES : To solve problems in current compaction control DCPT(Dynamic Cone Penetrometer Test), highly correlated with various testing methods, simple, and economic is being applied. However, it、s hard to utilize DCPT results due to the few numerical analyses for DCPT have been performed and the lack of data accumulation. Therefore, this study tried to verify the validation of numerical modeling for DCPT by comparing and analyzing the results of numerical analyses with field tests. METHODS: The ground elastic modulus and PR(Penetration Rate) value were estimated by using PFC(Particle Flow Code) 3D program based on the discrete element method. Those values were compared and analyzed with the result of field tests. Also, back analysis was conducted to describe ground elastic modulus of field tests. RESULTS : Relative errors of PR value between the numerical analyses and field tests were calculated to be comparatively low. Also, the relationship between elastic modulus and PR value turned out to be similar. CONCLUSIONS : Numerical modeling of DCPT is considered to be suitable for describing field tests by carrying out numerical analysis using PFC 3D program.

This study is focused on the channel design of bipolar plate in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv design of electrode. Since the flow rate and flow pattern of generated gas in the two phase flow system are the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL MultiphysicsTM to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator and flow pattern of two phase fluid in the electrode. In this study, liquid electrolyte flows into the bipolar plate and decomposed into gas phase, two phase flow simulation is applied to measure the efficiency of hydrogen gas generation.

This study is focused on the channel design of bipolar plate in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv design of electrode. Since the flow rate of generated gas is the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL MultiphysicsTM to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator.

우리 나라 남해안 연안에 부설된 소형정치망을 실험 수조의 크기 등을 고려하여 그 의 1/50의 크기로 Tauti의 어구 비교법칙에 따라 모형어구를 제작하여 유향 R(원통에서 헛통방향으로).L(헛통에서 원통방향으로)방향과 각각의 유속에 따라 그물 형상의 변화, 각 뜸의 침하량, 멍줄 장력의 변화 들을 측정, 관찰한 결과를 요약하면 다음과 같다. 1. 그물형상의 변화는 유향 R의 경우 유속 0.2m/sec에서 헛통 끝그물이 조하쪽으로 20mm, 상방으로 10mm 이동어구 전체가 바닥으로부터 부상하였고, 유속 0.6m/sec에서는 원통에서 헛통 까지 거의 일직선을 이루었다. 유향 L의 경우는, 상방으로 18mm 이동하여 어구 전체가 바닥으로부터 부상하였고, 유속 0.5m/sec이상에서는 헛통에서 원통까지 거의 일직선을 이루었다. 2. 긱 뜸의 침하량은 유향 R의 경우 머리뜸은 유속 0.2m/sec부터 서서히 침하하시 시작하여, 유속 0.3m/sec에서는 20mm 정도 침하하고, 유속 0.6m/sec에서는 99mm 정도 침하하였다. 그러나, 끝뜸은 유속 0m/sec부터 0.6m/sce까지 침하하지 않고 약간의 요동만 일으켰다. 유향 L의 경우 끝뜸은 유속 0.1m/sec에서부터 서서히 침하하기 시작하여, 0.2m/sec에서는 5mm정도 침하하였고, 0.6m/sec에서는 108mm 정도 침하하였으며, 0.5m/sec에서 머리뜸만 남기고 어구전체가 수몰되기 시작하였다. 3. 멍줄 장력의 변화는 유향 R의 경우 머리뜸 멍줄에 작용한 장력은 유속 0.1m/sec에서 273.51g이며, 0.6m/sec에서는 1298.40g 정도로 증가하였다. 유향 L의 경우 한쪽 끝뜸줄에 걸리는 장력은 유속 0.1m/sec에서 137.08g이며, 0.6m/sec에서 646.00g 정도로 증가하였다. 멍중 장력의 분포는 유속의 증대와 함게 유향 RL 향 모두 조상측 멍줄에 집중하여 나타났으며, 다른 멍줄에는 현저한 장력의 증가는 관측되지 않았다.되지 않았다.

There are many stringent environmental regulations on the management of waste electrical and electronic equipments(WEEE) in most developed countries. WEEE directive aims at increasing collection and recycling rate of WEEE whereas,while the restriction of the use of certain hazardous substances (RoHS) aims at restricting hazardous materials duringthe production of electrical and electronic equipment (EEE). TV housing rear covers consist of small portion of brominatedflame retardants (BFRs). Improper management and disposal of such waste can pose impacts on the environment andhuman health. In Korea, there are very few available statistical data regarding BFRs levels in TVs housing rear covers.In order to provide additional measures related to management of BFRs, there is a need for a quantitative material flowstudy on the amount of BFR found in TVs. This can be achieved by the aid of material flow analysis of the TV setsand by studying the Deca-BDE components present in the TV housing read covers. In this study, the relevant data werecollected from the statistical reports and through field site visits to the WEEE recycling facilities with surveys. Staticand dynamic material flow analysis (MFA) was conducted to determine material flow of BFRs (Deca-BDE) in themanagement of waste TVs. According to this study, in 2011, households in Korea use 73,821ton of TV sets of which23,592ton of waste TV sets were collected and recycled by municipalities and producers. Extended ProducerResponsibility (EPR) played a major role in recycling of WEEE. In this study, it was predicted that Deca-BDE in usestage would reach down to 51.73ton by 2016. In addition, the amount of Deca-BDE present at the disposal and recyclingstage is estimated to be approximately 2.45ton by 2018.