In order to overcome the limitations of linear vibration energy harvesters and those using mechanical plucking, magnetic plucking vibration energy harvesters (MVEs) have garnered significant interest. This paper presents parametric studies aimed at proposing design guidelines for MVEs and compares two magnetic force models that describe interactions between two permanent magnets. A mathematical model describing the energy harvester is employed, followed by the introduction of two magnetic force models: an analytic model and an inverse square model. Subsequently, numerical simulations are conducted to investigate dynamic characteristics of MVEs, analyzing results in terms of tip displacement, voltage output, and harvested energy. Parametric studies vary the distance between magnets, the speed of the external magnet, and the beam shape. Results indicate that reducing the distance between magnets enhances energy harvesting effectiveness. An optimal velocity for the external magnet is observed, and studies on beam shape suggest greater energy harvesting when the shape favors deflection.

Composite-based piezoelectric devices are extensively studied to develop sustainable power supply and selfpowered devices owing to their excellent mechanical durability and output performance. In this study, we design a leadfree piezoelectric nanocomposite utilizing (Ba0.85Ca0.15)(Ti0.9Zr0.1)O3 (BCTZ) nanomaterials for realizing highly flexible energy harvesters. To improve the output performance of the devices, we incorporate porous BCTZ nanowires (NWs) into the nanoparticle (NP)-based piezoelectric nanocomposite. BCTZ NPs and NWs are synthesized through the solidstate reaction and sol-gel-based electrospinning, respectively; subsequently, they are dispersed inside a polyimide matrix. The output performance of the energy harvesters is measured using an optimized measurement system during repetitive mechanical deformation by varying the composition of the NPs and NWs. A nanocomposite-based energy harvester with 4:1 weight ratio generates the maximum open-circuit voltage and short-circuit current of 0.83 V and 0.28 A, respectively. In this study, self-powered devices are constructed with enhanced output performance by using piezoelectric energy harvesting for application in flexible and wearable devices.

Piezoelectric technology, which converts mechanical energy into electrical energy, has recently attracted drawn considerable attention in the industry. Among the many kinds of piezoelectric materials, BaTiO3 nanotube arrays, which have outstanding uniformity and anisotropic orientation compared to nanowire-based arrays, can be fabricated using a simple synthesis process. In this study, we developed a flexible piezoelectric energy harvester (f-PEH) based on a composite film with PVDF-coated BaTiO3 nanotube arrays through sequential anodization and hydrothermal synthesis processes. The f-PEH fabricated using the piezoelectric composite film exhibited excellent piezoelectric performance and high flexibility compared to the previously reported BaTiO3 nanotube array-based energy harvester. These results demonstrate the possibility for widely application with high performance by our advanced f-PEH technique based on BaTiO3 nanotube arrays.

Thermoelectric (TE) energy harvesting, which converts available thermal resources into electrical energy, is attracting significant attention, as it facilitates wireless and self-powered electronics. Recently, as demand for portable/wearable electronic devices and sensors increases, organic-inorganic TE films with polymeric matrix are being studied to realize flexible thermoelectric energy harvesters (f-TEHs). Here, we developed flexible organic-inorganic TE films with p-type Bi0.5Sb1.5Te3 powder and polymeric matrices such as poly(3,4-eethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and poly (vinylidene fluoride) (PVDF). The fabricated TE films with a PEDOT:PSS matrix and 1 wt% of multi-walled carbon nanotube (MWCNT) exhibited a power factor value of 3.96 μW ‧ m-1 ‧ K-2 which is about 2.8 times higher than that of PVDF-based TE film. We also fabricated f-TEHs using both types of TE films and investigated the TE output performance. The f-TEH made of PEDOT:PSS-based TE films harvested the maximum load voltage of 3.4 mV, with a load current of 17.4 μA, and output power of 15.7 nW at a temperature difference of 25 K, whereas the f-TEH with PVDF-based TE films generated values of 0.6 mV, 3.3 μA, and 0.54 nW. This study will broaden the fields of the research on methods to improve TE efficiency and the development of flexible organic-inorganic TE films and f-TEH.

The fast expanding field of wearable technology requires light-weight, low-cost, scalable, flexible and efficient energy harvesters as a source of uninterrupted green power. This work reports fabrication of sub-micron graphite platelet/PVDF composite film-based flexible piezoelectric energy harvester (PGEH) for scavenging the wasted mechanical energy associated with human body motion. The addition of graphite platelet leads to the enhancement of electroactive β phase in PVDF; consequently, the piezoelectric and dielectric properties of the composite are enhanced. 0.5 wt% filler-loaded composite has 96% β phase fraction and dielectric constant 32 at 100 Hz (tanδ = 0.18).The PGEH produces open circuit voltage of 40 V and instantaneous power density of 3.35 mW cm− 3 with energy conversion efficiency of 22.5% under periodic finger tapping. It can generate fair electrical output under gentle heel (0.8 V) and toe movements (1.2 V). A PGEH is directly employed for powering 50 commercial LEDs and quick charging of a 2.2-μF capacitor upto 19.2 V. The device is also employed as self-powered dynamic pressure sensor which shows high sensitivity (0.9 VkPa− 1) with fast response time (1 ms). Therefore, this durable, flexible, efficient PGEH can have promising applications in wearable electronics as a green power source cum self-powered mechanosensor.

This paper developed a wind triboelectric nanogenerator(TENG) using cubic PTFE model. When the wind is injected, the cube PTFE is scattered inside the cylinder TENG structure and energy is harvested. The TENG structure was designed as a cylinder that allows independent dielectric to rotate well inside. In addition, an inlet and an outlet were made to allow good wind flow. Unlike wind harvesters, where one end is mostly fixed and energy is harvested, the dielectric's motion is freed using independent mode. The electrodes and dielectric materials used Aluminum(Al) and Polytetrafluoroethylene(PTFE). The cube PTFE dielectric contacts/separates the electrode attached to the inner wall of the cylinder along the inner wall of the cylinder. At this time, electricity is generated by the kinetic energy generated by the wind. In this study, the efficiency by the number of Cube PTFE inside the cylinder was compared. The experiment confirmed that as the number of Cube PTFE increases, the power increases, but if the number of Cube PTFE exceeds an appropriate number, the density inside the cylinder increases, interrupting the flow of wind, and thus decreasing the power.

In this study, the frequency response analysis of a bistable electromagnetic vibration energy harvester is performed, based on an electromagnetic oscillator model, to investigate its nonlinear dynamic behaviors. The displacement and current responses are obtained, by the direct integration of the model, with the variations of mechanical and electromagnetic parameters. It is shown that the operating frequency band of the system can be broadened by the increase in mechanical parameters(inertial mass and Q-factor), but it does not depend significantly on any electromagnetic parameters(an external load resistance and the internal resistance of a coil). On the other hand, the output current of the energy harvester is affected only by the electromagnetic parameters (specifically, the sum of two resistances). Thus, the mechanical and electromagnetic parameters of the electromagnetic energy harvester must be designed properly, respectively, for broader and more efficient performance.

A flexible piezoelectric energy harvester(f-PEH) that converts tiny mechanical and vibrational energy resources into electric signals without any restraints is drawing attention as a self-powered source to operate flexible electronic systems. In particular, the nanocomposites-based f-PEHs fabricated by a simple and low-cost spin-coating method show a mechanically stable and high output performance compared to only piezoelectric polymers or perovskite thin films. Here, the non-piezoelectric polymer matrix of the nanocomposite-based f-PEH is replaced by a P(VDF-TrFE) piezoelectric polymer to improve the output performance generated from the f-PEH. The piezoelectric hybrid nanocomposite is produced by distributing the perovskite PZT nanoparticles inside the piezoelectric elastomer; subsequently, the piezoelectric hybrid material is spin-coated onto a thin metal substrate to achieve a nanocomposite-based f-PEH. A fabricated energy device after a two-step poling process shows a maximum output voltage of 9.4 V and a current of 160 nA under repeated mechanical bending. Finite element analysis(FEA) simulation results support the experimental results.

As most infrastructure have low natural frequency for vibration, an energy harvester to operate wireless sensors for them should be aimed to low frequency and have high output efficiency. This study proposes the energy harvester with parallel-connected single crystal ceramic for low frequency in order to gain enhanced efficiency. The performance is confirmed by the experiment using the acceleration data of hangers in Yeongjong Bridge.

Despite the fact that wireless sensor is needed to be activated in order to do efficient and continuous management, batteries are limited on their lives in case of wireless sensor. This paper suggests that the energy harvester model can be used within low frequency and examined using single crystal PMN-PT material which is definitely good at the efficiency of piezoelectric in order to maximize the output power. And the possibility of wireless sensor node power supply is verified by using an acceleration data of cable hangers of YoungJong Grand Bridge.

본 연구에서는 진동-충격 영향을 고려한 비선형 해석을 통하여 스탑퍼의 유/무에 따른 켄틸레버형 압전 에너지 하비스터의 응답 특성을 해석하였다. 실험을 통하여 각 케이스에 따라 발생하는 전력을 측정하여 스탑퍼의 유/무가 압전 에너지 하비스터의 동적 특성에 미치는 영향을 분석하였다. 본 연구에서 제안한 압전 에너지 하비스터 모델은 1차 모드에서 공진주파수가 9Hz에서 8Hz로 감소했고 에너지 발생 효율은 저항이 800㏀에서 0.42mW가 0.58mW로 향상 되었다. 연구결과를 토대로 스탑퍼는 효율적인 변위제어를 통하여 취성 재료인 압전세라믹의 내구성을 향상 시키고 보호하는 역할을 함을 알 수 있었다.