The objective of this study was to achieve biological control of green mold disease in Pyogo mushrooms using antagonistic microorganisms. Bacillus subtilis BSM320 cells inhibited mycelial growth by 48–60% against three Trichodermaisolates including T. hazianumisolated from the substrates of Lentinula edodes, showing their antifungal activity.The bacteria were cultured to a high density of 4.2 x 109±113.7 cfu/mlin aqueous extract of composted spent mushroom substrates of L. edodes containing 1% glucose and showed a higher growth rate than that observed when using the commercial medium, Luria-Bertani broth. The bacterial culture showed a 75% protective effect without damaging the mushroom fruiting bodies. These results suggest that B. subtilis BSM320culture is suitable for biological control of green mold disease during mushroom cultivation.

The addition of a large amount of alloying elements reduces the compactibility and increases the compacting pressure, thereby shortening the life of the compacting die and increasing the process cost of commercial PM steel. In this study, the characteristic changes of Fe-Mo-P, Fe-Mn-P, and Fe-Mo-Mn-P alloys are investigated according to the Si contents to replace the expensive elements, such as Ni. All compacts with different Si contents are fabricated with the same green densities of 7.0 and 7.2 g/cm3. The transverse rupture strength (TRS) and sintered density are measured using the specimens obtained through the sintering process. The sintered density tends to decrease, whereas the TRS increases as the Si content increases. The TRS of the sintered specimen compacted with 7.2 g/cm3 is twice as high as that compacted with 7.0 g/cm3.

Spherical-type zirconia granules are successfully fabricated by a spray-drying process using a water solvent slurry, and the change in the green density of the granule powder compacts is examined according to the organic polymers used. Two organic binders, polyvinyl alcohol (PVA) and 2-hydroxyethyl methacrylate (HEMA), which are dissolved in a water solvent and have different degrees of polymerization, are applied to the slurry with a plasticizer (polyethylene glycol). The granules employing a binder with a higher degree of polymerization (PVA) are not broken under a uniaxial press; consequently, they exhibit a poor green density of 2.4 g/cm3. In contrast, the granule powder compacts employing a binder with a lower degree of polymerization (HEMA) show a higher density of 2.6 g/cm3 with an increase in plasticizer content. The packing behavior of the granule powders for each organic polymer system is studied by examining the microstructure of the fracture surface at different applied pressures.

본 연구는 강원도 원주시 도심지역인 행정동에 조성된 전체 공원과 녹지를 대상으로 식재 수종 및 식재밀도 특성을 분석하였다. 원주시 행정동지역 공원과 녹지에는 교목 침엽수 19종 8,050주, 활엽수 61종 6,037주, 관목 103종 77,609주가 식재되어 있었다. 근린공원, 어린이공원, 완충녹지, 경관녹지 4개 유형 모두 조성시기, 주변 토지이용 요인과 상관없이 침엽수인 스트로브잣나무의 수종 편중이 심하였고, 잣나무, 벚나무, 단풍나무, 느티나무, 소나무 순으로 식재 되어 있었다. 공원과 녹지의 평균 식재밀도는 교목 0.03주/㎡, 관목 0.18주/㎡로 대부분의 대상지는 식재밀도가 낮았고 관목식재가 미흡하였다. 녹지공간 내 잔디식재지가 넓어 식재밀도 증진과 관목류 보식이 필요하였다. 따라서 공원녹지내 추가로 식재할 수 있는 공간을 구분하여 미식재지역 내 수목 보식, 다층구조 식재, 관목 식재 등 식재밀도 증진을 제안하였다.