The hardware and the software of the prototype telemtry system to monitor the behavior of the fish are designed. This system consistes of five parts I. e. three omni-directional hydrophones, three ultrasonic receivers, a single board computer for the signal processing, two RF transceivers for the data communication, and a personnel computer. The sensitivty of the hydrophones is -170dB(re 1V/μPa), the gain and the 3dB receiving bandwidth of the ultrasonic receivers are 115dB and 1500Hz respectively, and the sampling period is 33.3μsec in the signal processing part. The positioning error of the system using hyperbolic method is estimated to be less than 0.2m in case that the pinger locates inside of the baselines. The perfomance of the system considering a practical use was examined by numerical simulation and a water tank test of a pinger tracking experiment. In results, the system developed in prototype was confirmed that it could be useful for monitoring the behavior of fish in the limited water area.

The speed of vertical migration and the volume backscattering strength of the scattering layers during the evening and morning transitions between day and night were measured in November 1990-1992 in thermally stratified waters of the East China Sea. Acoustical measurements were carried out using a scientific echo-sounder operating at t재 frequencies of 25 and 100kHz, and using an echo-integration system connected with a micro-computer. Biological sampling was accomplished by bottom trawling to identify fish species recorded on the echo sounder, and the species and length compositions were determined. The values of scattering strength were allocated to group of fishes according to the fish traces on the echo recording paper and the species composition of trawl catches. The vertical velocities of migration derived from the changes in the depths and the values of peak scattering strength of the dense layer vertically migrating toward the bottom or toward the surface. The trawl data suggest that snailfish and fishing frog were the most abundant fishes in all research stations. As sunrise approached, the fish formed a strong concentration just above the thermocline. The the highest values of scattering strength in the entire water column appeared in the depth strata above the thermocline just before the begining of downward migration. As soon as the fish began to migrate downwards across the thermocline, the values of the scattering strength in the depth strata above the thermocline rapidly decreased, while the values for the scattering layer moving slowly toward the bottom gradually increased. During the 1992 surveys, the speed of the vertical migration was estimated to be 0.38m/min in the upward migration and 0.32m/min in the downward migration, respectively. That is the rate of vertical migration was slightly higher at dusk than at dawn. Similar migration patterns were observed on different stations and under different weather conditions during the surveys in 1990.

The vertical distribution and activity patterns of fishes during the evening and morning transitions between day and night were studied acoustically and by bottom trawling in November 1990-1992 in thermally stratified waters of the East China Sea. The acoustic data were collected from six stations with a scientific echo-sounder operating at two frequencies of 25 and 100kHz, and the echograms were used to determine the vertical distributions of fish. Biological sampling was accomplished by bottom trawling to identify fish species recorded on the echograms, and the species and length compositions were determined. At each station, vertical profiles of water temperature, salinity and dissolved oxygen were taken with a CTD system and were related to the diel movements and the depth distributions of fish. During the day most fish were within several meters above bottom, but began to migrate upwards just before sunset, and during the night they were dispersed in midwater. Prior to sunrise with a thermocline present, one group of the fish aggregation occurred in dense schools slightly above the thermocline, while the other group occurred with the numerous single fish-traces bellow it. These groups of aggregations rapidly began to migrate toward the bottom across the thermocline from about 40 min before sunrise. Trawl hauls in the bottom strata below the thermocline with the characteristic single fish traces yieled invariably catches dominated by snailfish and fishing frog with minor quantities of other species in all stations. Hence, the results indicate that snailfish and fishing frog were the dominated scatterers in the depth strata below the thermocline, and the single-fish recordings were mainly snailfish. The fish species such as anchovy and juvenile mackerel in bottom trawl catches is poorly represented in relation to the mesh selectivity of the trawl net, but their occurrence suggest that the fish-school recording above the thermocline were due to these species which migrated vertically across the thermocline, with a temperature gradient of about 8℃, from the water layers near the bottom at night. Accordingly, we conclude that the vertical distribution and activity patterns of snailfish were strongly temperature dependent and in the termally stratified waters, the upper limit to diel activity was closely linked to the position of the thermocline.

The characteristics of the P(VDF-TrFE) acoustic microscope transducer were evaluated theoretically and experimentally by comparison with those of the PVDF and the ZnO acoustic microscope transducers. It was found that its insertion loss was about 5dB lower than that of the PVDF and about 13dB higher than that of the ZnO. And its relative bandwidth was 20% which could produce the effective acoustic pulse waves having about 4 periods duration into water. Another finding was that the effective horizontal focusing resolution and the focal depth were 120μM and 1.5mm, respectively.

In this paper the failure mechanisms of polypropylene resin composites filled with calcium carbonate particulates have been studied in the temperature range -50℃ to -50℃ The fillers used are both untreated and surface treated with stearic acid. The impact fracture toughness is evaluated from the impact energy absorbed divided by the uncut ligament area of the specimen. Impact fracture toughness increases as temperature is raised whether the fillers are coated or not. The static fracture toughness of these particular composites is evaluated based on the linear clastic fracture toughness of these particular composites is evaluated based on the linear clastic fracture mechanics. Static fracture toughess decreases with increasing temperature whether the fillers are coated or not. An extended stress whitened zone are observed through a large number of availabel sites for cavitation/debonding along particle matrix interface and matrix deformation.

3차원 二重 摸型이 粘性 流體中을 운동할 때 발생하는 점성 摩擦力을 感少시키기 위하여 船體 표면에 流線 방향으로 V-홈(Riblet)의 띠를 그 표면에 부착하였다고 가정하여 점성 마찰력 감소에 관하여 難流 境界層의 特性을 계산하는 수정된 방법을 구하고 그 계산을 위한 프로그램을 작성하였다. 계산 방법으로서는 Hess & Smith의 방법에 의하여 포텐시얼 유동을 계산하고 그것으로부터 구한 유속 값들을 Momentum 적분 방정식에 이용하였다. 補助 방정식으로서는 Head의 식과 점성 마찰력에 관한 Clauser의 식을 사용하였다. 그리고 Riblet의 효과로서는 Gaudet의 실험식을 이용하였다. 그 계산 결과 선체 전표면에 유선의 방향으로 Riblets를 付着하였다고 가정하였을 경우 상당한 점성 마찰력 減少效果를 나타냈으며 Riblet를 선체 전체길이 4등분하여 각각의 표면에 부착시켰을 때도 현저한 점성 마찰력 감소 효과를 나타냈으며 특히 선수 부분의 25% 표면에 부착되었을 때가 다른 영역에 부착하였다고 가정하였을 경우보다도 가장 優秀한 效果를 나타내었다.

The inverted pendulum is one of the control mechanism that has been frequently used to verify the control theory in the laboratory. In this paper, the author made an inverted pendulum driven by DC servomotor with a simple DC motor drive circuit, and constituted a control system. The control mechanism is modeled, and identified parameters of inverted pendulum system by experimental method. The author used the LQ regulator as control algorithm and the minimum order observer algorithm to observe states that can not be measured. And the validity of parameter identification and the excellent performance of the control system designed by LQR are confirmed

This paper describes the model of a simplified trawl system and a control method by using fuzzy algorithm in controlling the depth of trawl gear. Fuzzy logic control rules are sets of linguistic expression that are used by an experienced performer in real operation. For real time processing of the control rules, the look-up tables are used. Computer simulation results indicate that the proposed fuzzy controller shows fast response with minimum steady-state error and robustness properties to the simulated disturbance.

In recent years, navigational and fisheries instruments are rapidly advancing. Especially data processing. data transferring and data interchange throughout the digital signals has been in high progress. Even though the ship's heading is also provided by a gyro-compass, an electro-magnetic compass studying by us currently is easy to issue adequate data to instruments requiring the information for the ship's heading. especially in small fishing boats. As the main element of the electro-magnetic compass is a three-axis magnetic sensors, the developing of the high performance sensor is in highly necessity in the beginning. This paper describes on the development of electro-magnetic compass of three-axis fixed type by using three-axis detection new type magnetic sensor without gimbals. even though usual electro-magnetic compass have to need necessarily a gimbal system in order to keep horizontal condition of the compass.

The mesh selectivity of diamond and suare mesh cod-ends at the Southern Korean Sea and the East China Sea were compared for Pampus argenteus, Trachurus japonicus, Trichiurus lepturus. Selection trials were carried out using diamond and square mesh cod-end by trouser type cod-end with cover net. of which the mesh cod-end has four types : A(51.2mm), B(70.2mm), C(77.6mm), D(88.0mm). Selection curves and selection parameters were calculated using a logistic model. The results obained are summarized as follows : 1. Harvest fish : In B. C and D type selection range and fifty percent selection length of the square mesh were about 21mm, 11mm : 12mm, 18mm and 34mm, 5mm higher than those of the diamond mesh, respectively. Selection factor of master curve for the diamond mesh was 1.54 and for the square mesh was 1.68. The optimum mesh size for the diamond mesh was 97.4mm and for the square mesh was 89.3mm, the difference was 8.1mm. 2. Horse mackerel : In A type, selection range was nearly the same for the diamond and the square mesh, but fifty percent selection length of the square mesh was 43mm higher than the diamond mesh. In B. C and D type, selection range and fifty percent selection length of the square mesh were about 6mm, 3mm : 24mm, 21mm and 11mm, 42mm higher than those of the diamond mesh, respectively. Selection factor of master curve for the diamond mesh was 2.37, for the square mesh was 2.77. The optimum mesh size for the diamond mesh was 78.1mm and for the square mesh was 66.8mm, the difference was 11.3mm. 3. Hair tail : In A, B and C type, selection range of the square mesh was about 34mm, 8mm, 60mm higher than those of the diamond mesh. Fifty percent selection length for the diamond mesh was about 5mm, 7mm, 8mm higher than that of the square mesh. Selection factor of master curve for the diamond mesh was 3.11, for the square mesh was 3.48. The optimum mesh size for the diamond mesh was 64.3mm and for the square mesh was 57.5mm, the difference was 6.8mm.

Mesh selection analysis for the trawl net were carried out at the Southern Korean Sea and the East China Sea during the 1992-1994 years by the training ship Seabada of the National Fisheries University of Pusan, using A type (51.2mm), B type (70.2mm), C type (77.6mm), D type (88.0mm) square mesh cod-ends. The fishing trials were made using bottom trawl of the trouser type cod-end with cover net. Selection curves and selection parameters were calculated by a logistic model for Sphyraena pinguis, Pampus argenteus, Trachurus japonicus, Pagrus major, Callanthias japonicus, Trichiurus lepturus. The results obtained are summarized as follows: 1. Red barracuda : Selection range and fifty percent selection length in the A type was 115.8mm, 292.8mm, respectively. 2. Harvest fish : Each selection range and fifty percent selection length in the B. C. and D type was 37.7mm, 113.8mm : 40.1mm, 131.7mm and 64.8mm, 148.6mm, respectively. Selection parameters of master curve were : slope, 3.81 : intercept, -6.4. Optimum mesh size was 89.3mm. 3. Horse mackerel : Each selection range and fifty percent selection length in the A, B, C and D type was 43.0mm, 148.3mm : 60.7mm, 183.2mm, 214.5mm and 91.4mm, 254.9mm, respectively. Selection parameters of master curve were : slope 2.30 : intercept, -6.4. Optimum mesh size was 66.8mm. 4. Red seabrem : Selection range and fifty percent selection length in the D type was 42.7mm, 203.4mm, respectively. 5. Yellowsail red bass : Selection range and fifty percent selection length in the A type was 84.0mm, 110.6mm, respectively. 6. Hair tail : Each selection range and fifty percent selection length in the A, B and C type was 59.7mm, 176.0mm : 100.9mm, 250.7mm and 178.6mm, 307.0mm, respectively. Selection parameters of master curve were : slope, 1.54 : intercept, -5.4. Optimum mesh size was 57.5mm

Drift gillnet fishery for neon flying squid in the North pacific was one of the major pelagic fisheries of Korea until 1992, its annual catch was 79, 000M/T as average during 1988-1992, but moratoriumed since 1993 according to the decision of UN. Therefore, for the developing of the new fishing gear for the squid, the seven types of rip hook by automatic squid jigging machine were experimented by the korean research vessel Pusan 851 (G/T 1.126, 2.600 PS) in the North Pacific (38 ˚30'-43 ˚N, 152 ˚E-178 ˚W) from July 6. 1993 to August 31. 1993. The investigation on catch rate, dropout rate, and catch condition of the rip hooks related to the fishing lamp power for aggregating the squid were carried out during the period. The results obtained are as follows: The composition of catch by automatic squid jigging machine was 83.9% for neon flying squid. 15.5% for boreopacific gonate squid. 0.6% for boreal clubhook squid, and 0.01% for luminous flying squid. The catch rate of neon flying squid was 94.6% in 13.6-18.3℃ of surface water temperature and 5.4% in others. The higher catch rate of neon flying squid was made in the range 13.6-18.3℃ of temperature at the surface and about 10℃ of temperature at the 100m layer. The CPUE of neon flying squid in the 13.6-18.3℃ of surface water temperature was ranged 0.8-11.8kg (8.7kg as average). The mantle length and body weight of neon flying squid caught in the experiment were ranged 18.3-51.3 cm, 140-3, 980g and mean mantle length and mean body weight were 29.4cm, 972g respectively. The catch rate of neon flying squid was the highest at dawn with a value of 25.0% of the total catch. The body weight of neon flying squid caught by the D type hooks was 1.7 times more than that of the A type hooks. The dropout rate of neon flying squid caught by the seven types hooks was 7.9-57.5% (19.0% as average), and dropout rate of the D type hooks was 7.9% with 2.7 times decrease than that of the A type hooks. The catch efficiency of small sized neon flying squid in case of using on-off switch method on fishing lamp in 15 minutes intervals was 2.6 times higher than that of the on-switch method with same fishing lamp power.

In order to investigate the environmental properties of set net grounds located in the coastal waters of Yeosu. The current in the vicinity of set net grounds was observed by drogue and current meter in 1990 and 1992. The results obtained are summarized as follows: The direction of tidal current at the north enterance of Yeosu bay was southerly in ebb and northwesterly in flood without the distiction of the neap tide and the spring tide. In spring tide the maximum Velocity of the tidal current was 68 cm/sec in ebb and 66 cm/sec in flood. In neap tide the maximum velocity of the tidal current was 37 cm/sec in ebb and 35 cm/sec in flood. And so the direction of residual current was the south ward mainly and 21 cm/sec. The direction of tidal current at set net fishing grounds was southwesterly in ebb and westerly or northwesterly in flood. Regardless of the distinction of neap and spring. The maximum velocity of the current in spring tide was 50 cm/sec in ebb and 40 cm/sec in flood and that in neap was 28 cm/sec in ebb and 25 cm/sec in flood. In spring tide the speed vector along the major axis of semidiurnal tide component was three times as large as diurnal tide. In neap tide, however, the speed vector was about 50% less then that in spring tide, and the semidiurnal tide and diurnal tide were equal in the size of current ellipse and the direction of major axis. The sea area had a southwesterly residual current. 11 cm/sec in spring tide and 7 cm/sec in neap tide. According to the result of drogue tracking, the vicinity of set net fishing ground had a southerly residual current which formed in Yeosu Bay and a weak westerly residual current toward Dolsando from Namhedo. Therefore, set net fishing ground in coastal water of Yeosu was distributed in boundary of inner water which formed from Seamjin river and offshore water supplied from the vicinity of Sorido and Yochido.

In order to investigate remotely the behavior and distribution of fishes, the telesounder system which was composed of two parts with a buoy station at sea and a base station on land was manufactured trial. The buoy station at sea consists of fishfinder, transmission interface and transceiver. On the other hand, the base station on land consist of transceiver, receiving interface, trigger/signal separator and color display monitor. The system simulation for the performance of telesounder was carried out by use of echo simulator which could input echo signal into fishfinder. The received power (dBm) of transceiver at 29.4MHz decreased almost in proportion to distance between transmitter and receiver, and the electric field intensity was 12.12mV/m at 100 meters distance from transmitter. The image of color display monitor at the base station on land was very well coincident with the records of fishfinder from the buoy station located at sea. Therefore, it is concluded that the telesounder system is very useful in the analysis of the information on the behavior and the distribution of fishes detected from sea

This paper describes a method to measure the distortion level of loudspeaker using a LMS(Least Mean Square) adaptive filter. Conventional technique to measure the distortion level uses a band-pass filter with a sharp cut-off frequency characteristics. However. such the band-pass filter has a bed time response characteristics. On the other hand, the proposed method offers us an easy way to measure the specified harmonic distortion level with a small hardware. Moreover, our method is not affected by noise which has no correlation with the test signal, and the measurement can be carried out in a noisy environment. The effectiveness of the proposed method is confirmed by experiment using a loudspeaker in a noisy room.

There has been studied a lot of two dimensional hydrofoil sections for the boundary layers. This paper suggests that the plaiable roughness effects on boundary layer transition region of suction side for NACA 4412 hydrofoil sections provided by auxieiary shape factor and lag-entrainment effects. These results show that the laminar sepration. Transition and end of transition of the boundary layer due to pitting roughness effects, to the foil Reynold's number as well as to the angle of attack were delayed a little. And comparisons with valuable the other calculations and measurements show qualitative agreements.

This paper presents a new concept to reduce turbulent frictional drag by injecting micro-bubble into near the buffer layer of turbulent boundary layer on flat plate. The concentrations of micro bubble distribution in the boundary was calculater by eddy viscosity equations in the governing equations. When near region of the buffer layer of turbulent boundary layer is filled with micro-bulle of air and viscous of the region is kept low, the velocity profile in the near region should be changed substantially. Then the Reynolds stress in the region becomes less, which guide to lower velocity gradient there. It results in reduction of velocity gradient at the viscous sublayer, which gives the reduction of shear stress at the wall.

The DC Servo Motor has been used as an actuator in automatic control fields because of the good response and the control easiness nevertheless it has some disadvantage such as spark at the brush. Recently, along with the fast development of semiconductor industries, the digital control scheme is increasing in comparison with analog control because of the strength against noise and the accuracy. In this paper, authors proposed a combined control algorithm, which is mixed Modified Minimum Time Position Control(MMTPC) and PI control algorithm. for minimum time position control of DC Servo Motor by the one-chip microcontroller. The proposed control algorithm showed the fast response and offset-free. The validity of the proposed method comparing with the VSS control is proved by the response experiments.

In order to estimate the optimum harvesting mesh size of multispecies, the 24 species of catching data which were taken by fishing trial of trawl gear in Korean Southern Coast and East China Sea during 1991-1993 year were grouped and divided by the Cluster analysis method, considering first maturity length and body width, body height, body girth based on the first maturity length. With the same method, the above groups were subdivided by the potential escape such as possible escape index, range factor and selection factor. In case of the species devoid of selection parameters, these species were first subdivided by the use of possible escape index and length range factor. Next, the optimum harvesting mesh size of multispecies was properly classified according to the optimal mesh size of a fish estimated by first maturity length against selection factor. The results obtained are summarized as follows: 1. Each optimum harvesting mesh size of Psenopsis anomala, Priacanthus macra-canthus, Trachurus japonicus, Argyrosomus argentatus was 71.1-79.5mm, and Saurida undosquamis was 65.5mm. 2. Each optimum harvesting mesh size of Scomber japonicus, Pseudosciaena crosea, Pseudosciaena Polyactis, Sebastes thompsoni, Doderleinia berycoides was 78.5-85.6mm, and Bembras japonicus, Sphyraena pinguis was 48.4-51.3mm. 3. Each optimum harvesting mesh size of Zeus faber, Pampus argenteus, Zenopsis nebulosan was 118.4-124.1mm, and Caranx equula was 91.4mm, and Thamnaconus modestus was 131.2mm, and Pagrus major was 149.4mm. 4. Each optimum harvesting mesh size of Upeneus bensasi, Callanthias japonicus, Sardinops melanosticata, Konosirus punctatus was 36.8-42.8mm, and Acropoma japonicum was 21.2mm, and Apogon lineatus was 26.3mm.

The author carried out an experiment to find out the response of Striped puffer. Fugu xanthoperus (Temminck et Schlegel) to the color lights. The experimental tank (300L×50W×50Hcm) was set up in a dark room. Six longitudinal sections with 60cm intervals are marked in the tank to observe the location of the fish. Water depth in the tank was kept 50cm level. Light bulbs of 20W at the both ends of the tank projected the light horizontally into the tank. Two different colored filters were selected from four colors of red, blue, yellow, and white, and the were placed in front of the light bulbs to make different colors of light. Light intensity was controlled by use of auxiliary filiters intercepted between the bulb and the filter. The fishes were acclimatized in the dark for 60 minutes before they were employed in the experiment. Upon turning on the light, the number of fish in each section was counted 40 times in 30 second intervals, and the mean of the number of fish in each section was counted 40 times in 30 second intervals, and the mean of the number of fish in each section was given as the gathering rate of the fish. The colors favourited by the fish was found in order of blue, yellow, white and red in the daytime, and blue, white, yellow and red at night. The difference of the average distribution on two different colors of light was 13.12%(4.10-26.55%), and the difference in the daytime(14.79%) was larger than at night (11.45%). Constantly the gathering rate of fish on illumination period was fluctuated with instability. As the gathering rate of fish on illumination period was fluctuated with instability. As the gathering rate on one color of light increased, the gathering rate on the other color of light decreased. The difference of the gathering rate on two different colors of light was comparatively distinct and the difference in the daytime was larger than at night.