A serious of study is carried out to practical use of the three-slot cambered otter board improved by the authors. As the first step, we designed main plates, slots and accessories, such as holding plate, fan-shaped towing plate, normans, center ring, etc. Standing on this design, we made the simple cambered and three-slot cambered model otter board with accessories in a linear scale 6:1. and carried out model test to examine the efficiency of these boards. The obtained results can be summarized as follows: 1. On the simple cambered board with accessories, the values of the maximum shear coefficient(C LX ). drag coefficient((C D) and hydrodynamic efficiency(C L/C D ) are 1.39, 0.56, 2.48 at 22˚ of the angle of stall respectively. 2. On the three-slot cambered board with accessories, C LX/C D and C I/C D are 1.67, 0.92, 1.82 at 32˚ of the angle of stall respectively. 3.C LX of board with accessories is smaller 10~12% than that of only the main plate, and the angle of stall is almost same. 4. C LX and the angle of stall of the three-slot cambered board with accessories are greater 20% and 〈TEX〉10˚〈TEX〉 than that of the simple cambered board respectively.
The author carried out an experiment to find out the response of Striped puffer. Fugu xanthoperus (Temminck et Schlegel) to the color lights. The experimental tank (300L×50W×50Hcm) was set up in a dark room. Six longitudinal sections with 60cm intervals are marked in the tank to observe the location of the fish. Water depth in the tank was kept 50cm level. Light bulbs of 20W at the both ends of the tank projected the light horizontally into the tank. Two different colored filters were selected from four colors of red, blue, yellow, and white, and the were placed in front of the light bulbs to make different colors of light. Light intensity was controlled by use of auxiliary filiters intercepted between the bulb and the filter. The fishes were acclimatized in the dark for 60 minutes before they were employed in the experiment. Upon turning on the light, the number of fish in each section was counted 40 times in 30 second intervals, and the mean of the number of fish in each section was counted 40 times in 30 second intervals, and the mean of the number of fish in each section was given as the gathering rate of the fish. The colors favourited by the fish was found in order of blue, yellow, white and red in the daytime, and blue, white, yellow and red at night. The difference of the average distribution on two different colors of light was 13.12%(4.10-26.55%), and the difference in the daytime(14.79%) was larger than at night (11.45%). Constantly the gathering rate of fish on illumination period was fluctuated with instability. As the gathering rate of fish on illumination period was fluctuated with instability. As the gathering rate on one color of light increased, the gathering rate on the other color of light decreased. The difference of the gathering rate on two different colors of light was comparatively distinct and the difference in the daytime was larger than at night.
In order to estimate the optimum harvesting mesh size of multispecies, the 24 species of catching data which were taken by fishing trial of trawl gear in Korean Southern Coast and East China Sea during 1991-1993 year were grouped and divided by the Cluster analysis method, considering first maturity length and body width, body height, body girth based on the first maturity length. With the same method, the above groups were subdivided by the potential escape such as possible escape index, range factor and selection factor. In case of the species devoid of selection parameters, these species were first subdivided by the use of possible escape index and length range factor. Next, the optimum harvesting mesh size of multispecies was properly classified according to the optimal mesh size of a fish estimated by first maturity length against selection factor. The results obtained are summarized as follows: 1. Each optimum harvesting mesh size of Psenopsis anomala, Priacanthus macra-canthus, Trachurus japonicus, Argyrosomus argentatus was 71.1-79.5mm, and Saurida undosquamis was 65.5mm. 2. Each optimum harvesting mesh size of Scomber japonicus, Pseudosciaena crosea, Pseudosciaena Polyactis, Sebastes thompsoni, Doderleinia berycoides was 78.5-85.6mm, and Bembras japonicus, Sphyraena pinguis was 48.4-51.3mm. 3. Each optimum harvesting mesh size of Zeus faber, Pampus argenteus, Zenopsis nebulosan was 118.4-124.1mm, and Caranx equula was 91.4mm, and Thamnaconus modestus was 131.2mm, and Pagrus major was 149.4mm. 4. Each optimum harvesting mesh size of Upeneus bensasi, Callanthias japonicus, Sardinops melanosticata, Konosirus punctatus was 36.8-42.8mm, and Acropoma japonicum was 21.2mm, and Apogon lineatus was 26.3mm.
The DC Servo Motor has been used as an actuator in automatic control fields because of the good response and the control easiness nevertheless it has some disadvantage such as spark at the brush. Recently, along with the fast development of semiconductor industries, the digital control scheme is increasing in comparison with analog control because of the strength against noise and the accuracy. In this paper, authors proposed a combined control algorithm, which is mixed Modified Minimum Time Position Control(MMTPC) and PI control algorithm. for minimum time position control of DC Servo Motor by the one-chip microcontroller. The proposed control algorithm showed the fast response and offset-free. The validity of the proposed method comparing with the VSS control is proved by the response experiments.
This paper presents a new concept to reduce turbulent frictional drag by injecting micro-bubble into near the buffer layer of turbulent boundary layer on flat plate. The concentrations of micro bubble distribution in the boundary was calculater by eddy viscosity equations in the governing equations. When near region of the buffer layer of turbulent boundary layer is filled with micro-bulle of air and viscous of the region is kept low, the velocity profile in the near region should be changed substantially. Then the Reynolds stress in the region becomes less, which guide to lower velocity gradient there. It results in reduction of velocity gradient at the viscous sublayer, which gives the reduction of shear stress at the wall.
There has been studied a lot of two dimensional hydrofoil sections for the boundary layers. This paper suggests that the plaiable roughness effects on boundary layer transition region of suction side for NACA 4412 hydrofoil sections provided by auxieiary shape factor and lag-entrainment effects. These results show that the laminar sepration. Transition and end of transition of the boundary layer due to pitting roughness effects, to the foil Reynold's number as well as to the angle of attack were delayed a little. And comparisons with valuable the other calculations and measurements show qualitative agreements.
This paper describes a method to measure the distortion level of loudspeaker using a LMS(Least Mean Square) adaptive filter. Conventional technique to measure the distortion level uses a band-pass filter with a sharp cut-off frequency characteristics. However. such the band-pass filter has a bed time response characteristics. On the other hand, the proposed method offers us an easy way to measure the specified harmonic distortion level with a small hardware. Moreover, our method is not affected by noise which has no correlation with the test signal, and the measurement can be carried out in a noisy environment. The effectiveness of the proposed method is confirmed by experiment using a loudspeaker in a noisy room.