간행물
수산해양기술연구 KCI 등재 Journal of the Korean Society of Fisheries and Ocean Technology 韓國漁業技術學會誌
- 발행기관 한국수산해양기술학회(구 한국어업기술학회)
- 자료유형 학술지
- 간기 계간
- ISSN 2671-9940 (Print)2671-9924 (Online)
- 수록기간 1965 ~ 2024
- 주제분류 농수해양 > 수산학 농수해양 분류의 다른 간행물
- 십진분류KDC 529DDC 639
권호리스트/논문검색
권호
33권 1호 (1997년 2월) 8건
1.
1997.02
구독 인증기관 무료, 개인회원 유료
To find the tooth selectivity of the dredge for catching the ark shell Scapharca broughtonii, the probabilities of the ark shells which are not sifting through the gaps between teeth were calculated for the various shell lengths. Considering that these probabilities are in proportion to the relative catching efficiencies, selectivity curves for the ark shell dredge were estimated for the various gaps between teeth. The ratio of the shell length of ark shell to the distance between teeth indicating the relative catching efficiencies of 0%, 50%, 100% respectively, were calculated by using these selectivity curves, and the values were 1.00, 1.32, 1.54 in the distance of 4.0cm between teeth and then, the ratios showed a slight tendency to decrease as the distance between teeth increased in the relative catching efficiency of 100%, In addition, the range of shell length for catching, that is, the range of selective shell length by the distance between teeth was 0.54 in the distance of 4.0cm between teeth.
4,000원
2.
1997.02
구독 인증기관 무료, 개인회원 유료
Stokes drift(SD) and Lagrangian discharge(LD) are important factors for analysis of flushing time, tidal exchange, solute transport and pollutant dispersion. The factors should be calculated using the approached method to flow phenomena. The aim of this paper re-examines the previous procedures for computing the SD and LD, and is to propose the new method approached to stratified flow field in the cross-section of coastal region, e.g. Masan Bay. The intensity of velocity near the bottom boundary layer(BBL) depends on the sea-bed irregularity in the coastal estuaries. So we calculated the depth mean velocity(DMV) considering that of BBL omitted in Kjerfve's calculation method. It revealed that BBL effect resulting in application of the bay acts largely on DMV in half more among 1l stations. The new expression of SD and LD per unit width in the cross-section using the developed DMV and proposed decomposition procedure of current were derived as follow : Q=u0+½H1U1cos(Φh-Φu)+U3cos(Φh-Φud) LD ED SD(Qskim+Qsk2) The third term, Qsk2, on the right-hand of the equation is showed newly and arise from vertical oscillatory shear. According to the results applied in 3 cross-sections including 11 stations of the bay, the volume difference between proposed and previous SD was founded to be almost 2 times more at some stations. But their mean transport volumes over all stations are 18% less than the previous SD. Among two terms of SD, the flux of second term, Qskim, is larger than third term, Qsk2, in the main channel of cross-section, so that Qskim has a strong dependence on the tidal pumping, whereas third term is larger than second in the marginal channel. It means that Qsk2 has trapping or shear effect more than tidal pumping phenomena. Maximum range of the fluctuation in LD is 40% as compared with the previous equations, but mean range of it is showed 11% at all stations, namely, small change. It mean that two components of SD interact as compensating flow. Therefore, the computation of SD and LD depend on decomposition procedure of velocity component in obtaining the volume transport of temporal and spacial flow through channels. The calculation of SD and LD proposed here can separate the shear effect from the previous SD component, so can be applied to non-uniform flow condition of cross-section, namely, baroclinic flow field.
5,200원
3.
1997.02
구독 인증기관 무료, 개인회원 유료
The aim of the present study is to investigate experimentally the mechanism of an exploding wire in water and also to observe the bubble motion induced by an exploding wire. The experiment of an exploding wire is carried out in a water tank. As a metallic wire, a tungsten wire of 0.2mm in diameter and 10mm in length is employed. The electric energy of 50-300J is fed to the wire from a capacitor of 100μF charged up to 1-2.5kV. The explosion is recorded by a CCD camera with the resolution of 1μsec. The explosion process of metallic wire is divided into three phases. Phase 1 : As the voltage is applied to the wire, the temperature increases due to Joule heating and the wire emits light. Phase 2 : Then the wire melts and the cylindrical plasma is formed between the electrodes. Up to this stage, strong light emission is observed. Phase 3 : The light emission goes out and a vapor bubble begins to grow spherically. The radius of a bubble oscillates in time, but the amplitude of oscillation diminishes in several cycles.
4,200원
4.
1997.02
구독 인증기관 무료, 개인회원 유료
The steady drift forces on a barge in waves are investigated. The steady drift forces due to a near-field method which is based on direct integration of the pressure acting on the submerged surface of barge are compared with those due to far-field method which is based on the theory of momentum conservation. Numerical results of the linear motions are compared with the experimental and numercal ones which was submitted in the literature. A convergence of the steady drift forces according to the increase of the number of panels which represent the submerged surface are discussed.
4,000원
5.
1997.02
구독 인증기관 무료, 개인회원 유료
The energy saving is one of the most important factors for profit in marine transportation. In order to reduce the fuel oil consumtion the ship's propulsion efficiency must be increased as possible. The propulsion efficiency depends upon a combination of an engine and a propeller. The propeller has better efficiency as lower rotational speed. This situation led the engine manufacturers to design the engine that has low speed, long stroke and a small number of cylinders. Consequently, the variation of rotational torque became larger than before because of the longer delay-time in fuel oil injection process and an increased output per cylinder. As this new trends the conventional mechanical-hydrualic governors for engine speed control have been replaced by digital speed controllers which adopted the PID control or the optimal control algorithm. But these control algorithms have not enough robustness to suppress the variation of the delay-time and the parameter perturbation. In this paper we consider the delay-time and the perturbation of engine parameters as the modeling uncetainties. Next we design the robust servo controller which has zero offset in steady state engine speed, based on H sub(∞) control theory. The validity of the controller was investigated through the response simulation. We used a personal computer and an analog computer as the digital controller and the engine (plant) part respectively. And, we could certify that the designed controller maintains its robust servo performance even though the engine parameters may vary.
4,500원
6.
1997.02
구독 인증기관 무료, 개인회원 유료
This paper gives a controller design method by Linear Matrix Inequality(LMI) for internal combustion engine with Continuously Variable Transmission(CVT) which satisfies the given H∞ control performance and robust stability in the presence of physical parameter perturbations. To the end, the validity and applicability of this approach are illustrated by simulation in the all engine operating regions.
4,000원
7.
1997.02
구독 인증기관 무료, 개인회원 유료
In this paper, we propose the improved initial image estimation method for a fast fractal image decoding. When the correlation between a domain and a range is given as the linear equation, the value of initial image estimation using the conventional method is the intersection between its linear equation and y=x. If the gradient of linear equation is large, that the difference of the value between each adjacent pixels is large, the conventional method has disadvantage which has the impossibility of exact estimation. The method of the proposed initial image estimation performs well by two steps. he first step can improve the disadvantage of the conventional method. The second step upgrades the range value which was found previous step by referring information of its domain. Though the computational complexity for the initial image estimation increses slightly, the total computational complexity decreases by 30% than that of the conventional method because of diminishing in the number of iterations.
4,000원
8.
1997.02
구독 인증기관 무료, 개인회원 유료
To investigate a safety margin in the design of structural plant, plastic collaspse behaviors of statically indeterminate beams were numerically as the preliminary study. Through the calculations, it was revealed that the ultimate strength of statically indeterminate beams is much higher than that of statically determinate beams.
4,000원
