간행물
수산해양기술연구 KCI 등재 Journal of the Korean Society of Fisheries and Ocean Technology 韓國漁業技術學會誌
- 발행기관 한국수산해양기술학회(구 한국어업기술학회)
- 자료유형 학술지
- 간기 계간
- ISSN 2671-9940 (Print)2671-9924 (Online)
- 수록기간 1965 ~ 2024
- 주제분류 농수해양 > 수산학 농수해양 분류의 다른 간행물
- 십진분류KDC 529DDC 639
권호리스트/논문검색
권호
59권 1호 (2023년 2월) 10건
1.
2023.02
구독 인증기관 무료, 개인회원 유료
In this study, the stability of fishing boat inducing the change of fishing lamp in accordance with the installation of induction lamp in comparison with metal halide lamp was investigated. Inclining test for 8.55 ton class of hair-tail angling fishing boat was performed in order to find a GM and light weight. A stability calculation of the target fishing boat on the basis of KST-SHIP program was evaluated. The stability of the fishing boat with a metal halide lamp such as induction lamp according to the result obtained by the inclining test is slightly different, and the stability is not so much affected. Due to the induction lamp installation, the wind area increased by about 3.178 m 2 . Before installing the induction fishing lamp, G0M was found to be 0.209 at full load departure and 0.296 at departure from fishing ground. After installing the induction lamp, the full load departure condition is 0.178 and the fishing ground departure condition is 0.260. The G0M value before and after installation of the induction fishing lamp shows a difference of about 3% at the full load departure condition. The value of the critical angle of inclination definition showed a difference of about 16%. Despite these differences, it is lower than the regulations; it was confirmed that there will be no significant difference unless it is in an overloaded state.
4,000원
2.
2023.02
구독 인증기관 무료, 개인회원 유료
Fish samples were collected by a set net from April to December 2020 at the coastal waters off Tongyeong, Korea to determine fish species composition and seasonal variation. A total of 330,675 fish (1,032,578 g) representing 56 species belonging to 39 families were collected during the sampling period. The dominant species were Engraulis japonicus, Trachurus japonicus and Trichiurus japonicus, which accounted for 98.1% of the total number of individuals and 87.5% of the total biomass collected. E. japonicus and Chelidonichthys spinosus appeared every month off the coast of the Tongyeong. Cluster analysis based on the number of individuals of fish were classified into two groups at the dissimilarity level of 57%, and the results of ANOSIM analysis revealed significant differences in community structure among the two groups
4,000원
3.
2023.02
구독 인증기관 무료, 개인회원 유료
The interest in greenhouse gases (GHG) emitted from all industries is emerging as a very important issue worldwide. This is affecting not only the global warming, but also the environmentally friendly competitiveness of the industry. The fisheries sector is increasingly interested in greenhouse gas emissions also due to the Paris Climate Agreement in 2015. Korean industry and government are also making a number of effort to reduce greenhouse gas emissions so far, but the effort to reduce GHG in the fishery sector is insufficient compared to other fields. Especially, the investigation on the GHG emissions from Korean fisheries did not carry out extensively. The studies on GHG emissions from Korean fishery are most likely dealt with the GHG emissions by fishery classification so far. However, the forthcoming research related to GHG emissions from fisheries is needed to evaluate the GHG emission level by species to prepare the adoption of Environmental labels and declarations (ISO 14020). The purpose of this research is to investigate which degree of GHG emitted to produce the species (swimming crab and snow crab) from various fisheries. Here, we calculated the GHG emission to produce the species from the fisheries using the life cycle assessment (LCA) method. The system boundary and input parameters for each process level are defined for LCA analysis. The fuel use coefficients of the fisheries for the species are also calculated according to the fuel type. The GHG emissions from sea activities by the fisheries will be dealt with. Furthermore, the GHG emissions for producing the unit weight species and annual production are calculated by fishery classification. The results will be helpful to establish the carbon footprint of seafood in Korea.
4,000원
4.
2023.02
구독 인증기관 무료, 개인회원 유료
In the anchovy boat seine fishing boat, it is necessary to select other aquatic organisms other than live anchovies, which are the target species of catch. By making a rotating roller sorter using hydraulic pressure, the anchovy sorting amount was compared and the sorting accuracy of the rotary roller sorter, and the discharge speed of butter fish and jerry fish according to the number of roller revolutions were analyzed. The rotating roller sorter increases the weight of the sorted raw anchovy by 54%, 74% and 91.5% compared to the round bar fixed type, so it can reduce the required time by an average of 73.2%. As a result of converting the sorting accuracy to the weight of pure anchovies excluding the catch weight, the round bar fixed type was 89%; however, the average of the rotating roller sorter was 97.7%. Thus, the sorting accuracy of the rotary roller sorter was further improved by about 8.7%. The roller speed moved 7% at 300 rpm, 7.5% at 600 rpm, and 16% at 900 rpm, so butter fish were discharged overboard 10% faster than jelly fish on average. In addition, the average feed speed of butter fish and jelly fish is 1,400 mm/s when the roller rotation speed is 300 rpm, 1,480 mm/s at 600 rpm, and 1,850 mm/s at 900 rpm. A Φ58 mm roller rotates once it moved about 1.23 mm. In the future, a follow-up study of quantitative evaluation is needed targeting more non-target fish species of anchovy boat seine.
4,000원
5.
2023.02
구독 인증기관 무료, 개인회원 유료
Sensory evaluation of shucking pressure, pressure holding time, seeding method, difference in full shucking rate in the aquaculture area and shucking oyster was performed using an ultra-high pressure oyster shucking machine. The reaching time for each target pressure is 2.2-2.4 MPa/sec in the range of 180 MPa to 240 MPa. had a rate of pressure rise. There was a difference of 0.5-1.7℃ in the range of 24-27℃ in the seawater temperature before and after the pressure treatment inside the pressure vessel, but there was no specific increase or decrease in seawater temperature. When only the shucking pressure is increased without the pressure holding time, the critical shucking pressure at which the oyster shell is opened and the flesh is peeled in the range of 200 to 220 MPa. When the critical shucking pressure is reached, the oyster sample in the closed vessel is expected to be shucked by about 40%. If there is no pressure holding time when judged only by full shucking, an increase in pressure of about 1.5 MPa is required to further shuck 3% of the oyster population. The oyster samples cultivated in the south coast of Korea were subject to full shucking under the conditions of 220 MPa shucking pressure and two minutes (120 seconds) of pressure holding time, and the difference in the pressure of the oysters according to the oyster seeding method and the farming area was minute. Finally, the condition of 220 MPa of shucking pressure and three minutes of pressure holding time was the best at 1.52 when the result of the sensory evaluation performed manually was set to 1.0. Next was 1.4 under the conditions of 220 MPa of shucking pressure and one minute of pressure holding time (60 seconds), and 1.3 under the condition of 220 MPa and two minutes of pressure holding time (120 seconds). Therefore, it is considered that the most desirable shucking conditions, considering the efficiency and sensory evaluation results, are the conditions of 220 MPa shucking pressure and two to three minutes of pressure holding time.
4,000원
6.
2023.02
구독 인증기관 무료, 개인회원 유료
In this study, the second-order Nomoto’s nonlinear expansion model was implemented as a Tagaki-Sugeno fuzzy model based on the heading angular velocity to design the automatic steering system of a ship considering nonlinear elements. A Tagaki-Sugeno fuzzy PID controller was designed using the applied fuzzy membership functions from the Tagaki-Sugeno fuzzy model. The linear models and fuzzy membership functions of each operating point of a given nonlinear expansion model were simultaneously tuned using a genetic algorithm. It was confirmed that the implemented Tagaki-Sugeno fuzzy model could accurately describe the given nonlinear expansion model through the Zig-Zag experiment. The optimal parameters of the sub-PID controller for each operating point of the Tagaki-Sugeno fuzzy model were searched using a genetic algorithm. The evaluation function for searching the optimal parameters considered the route extension due to course deviation and the resistance component of the ship by steering. By adding a penalty function to the evaluation function, the performance of the automatic steering system of the ship could be evaluated to track the set course without overshooting when changing the course. It was confirmed that the sub-PID controller for each operating point followed the set course to minimize the evaluation function without overshoot when changing the course. The outputs of the tuned sub-PID controllers were combined in a weighted average method using the membership functions of the Tagaki-Sugeno fuzzy model. The proposed Tagaki-Sugeno fuzzy PID controller was applied to the second-order Nomoto’s nonlinear expansion model. As a result of examining the transient response characteristics for the set course change, it was confirmed that the set course tracking was satisfactorily performed.
4,200원
7.
2023.02
구독 인증기관 무료, 개인회원 유료
Gas turbine engines are widely used as prime movers of generator and propulsion system in warships. This study addresses the problem of designing a DS-based PID controller for speed control of the LM-2500 gas turbine engine used for propulsion in warships. To this end, we first derive a dynamic model of the LM-2500 using actual sea trail data. Next, the PRC (process reaction curve) method is used to approximate the first-order plus time delay (FOPTD) model, and the DS-based PID controller design technique is proposed according to approximation of the time delay term. The proposed controller conducts set-point tracking simulation using MATLAB (2016b), and evaluates and compares the performance index with the existing control methods. As a result of simulation at each operating point, the proposed controller showed the smallest in , which means that the rpm does not change rapidly. In addition, IAE and IAC were also the smallest, showing the best result in error performance and controller effort.
4,000원
8.
2023.02
구독 인증기관 무료, 개인회원 유료
This study analyzed the duct characteristics of hubless rim-driven propeller (RDP) used in underwater robots. In the previous study, flow visualization experiments were performed with an advancing ratio of 0.2 to 1. The vortex at the front of the duct increased in strength while maintaining its size as the advancing ratio decreased. Therefore, it is necessary to study the optimization of the duct shape. Conventional propeller thrusters use acceleration/deceleration ducts to increase their efficiency. However, unlike conventional propellers, it is impossible to apply to airfoil acceleration/deceleration ducts due to the RDP structure. In this study, duct wake flow characteristics, thrust force, and efficiency according to the duct shape of RDP were analyzed using numerical analysis techniques. Duct design is limited and six duct shapes were designed. As a result, an optimized duct shape was designed considering duct wake flow characteristics, thrust force, and efficiency. The shape that the outlet width of the RDP was kept constant until the end of the duct showed higher thrust force and efficiency.
4,000원
9.
2023.02
구독 인증기관 무료, 개인회원 유료
This paper is the result of a comparative analysis of crew members' workloads using the EMG and OWAS methods according to the fishing process before and after the improvement of the operating system of the experimental vessel, with the aim of improving operational efficiency and safety work of coastal improved stow net fishing vessels. The target crew members were three people with at least five years of experience on board the same fishing vessel as the experimental vessel. After improving the operating system, such as installing a power block crane and two capstans, change the location of the ball-roller, the time required for setting and hauling work decreased (p < .01), and the evaluation results by OWAS showed that the overall workload for setting and hauling net work decreased. The results of muscle activity analysis showed a decrease in lashing anchor work (p < .01) in the case of hauling net and in anchor dropping work in the case of setting net (p < .001). It is judged that the use of ball rollers in net handling has been reduced; consequently, work safety has been improved.
4,200원
10.
2023.02
구독 인증기관 무료, 개인회원 유료
The IPA-based introductory survey and analysis for the safe fishery of the coastal gillnet fisheries
This study analyzes the importance and implementation of countermeasures to reduce safety accidents that may occur during fishing in coastal gillnet fishing. Safety accidents that may occur in coastal gillnet fishing were classified into 56 measurement items in six areas: slips and trips, contact with machinery, falls, struck by object, musculoskeletal symptoms, and electrical shock. 35 fishermen belonging to coastal gillnet associations in Tongyeong and Namhae were selected as samples, and the importance and implementation of the proposed measurement items were investigated in the field. In addition, the results were evaluated visually by IPA analysis. As a result of the analysis, the importance of struck by object was the highest, and the implementation of slips and trips was the highest. On the other hand, prevention of musculoskeletal damage was found to be the lowest in both importance and implementation. The area with the most significant difference in importance and implementation by the classified area for measurement items was struck by object, and the area with the minor difference was slips and trips. Among the measurement items, the importance is highly recognized, but there are items with low implementation. To improve their level of implementation, countermeasures such as continuous education, economic support, and structural change of fishing boats should be prepared; moreover, policy support activities for implementation should be carried out.
4,600원
