In general, systems are developed by repeatedly performing the processes of design, analysis, manufacturing, and performance testing. In particular, systems with temperature, pressure, and flow rate often utilize computational fluid dynamics tools at the design stage. In this paper, we aim to verify the reliability of the analysis results of Solidworks Flow Simulation, which is widely used in heat flow analysis at the design stage. A tube furnace was manufactured, various experiments were performed, and a study was conducted to compare the analysis results. The details of the experiment are as follows. First, an experiment was conducted in which the heater was heated to 900°C without insulating the exposed part of the tube. The detailed contents of the experiment are as follows; - Heating heater and measuring temperature without supplying flow inside the tube, - Tube flow supply (25°C, 15 lpm air) and heater heating/temperature measurement. Second, an experiment was performed in which the exposed part of the tube was insulated (thickness 50 mm) and the heater was heated to 900°C. The detailed contents of the experiment are as follows; - Insulate the outside of the tube except for the flanges at both ends of the tube, and heat the heater and measure the temperature without supplying flow inside the tube. - Insulate the outside of the tube except for the flanges at both ends of the tube, supply flow rate inside the tube (25°C, 15 lpm air) and measure heater heating/temperature. - Insulate the flange of the flow supply section, heat the heater and measure temperature without supplying flow inside the tube. - Insulate the flange of the flow supply section, heat the supply air (277°C, 15 lpm) and measure the temperature using a heating gun without heating the heater. - Insulate the flange of the flow supply section, supply heated air (277°C, 15 lpm) and measure heater heating/temperature. - Insulate the flange of the flow supply section and measure temperature according to heater heating (900°C) and supply temperature (25°C, 277°C 15 lpm). The following results were derived from the experimental and analysis results. - When the exposed part of the tube is insulated, the temperature inside the tube increases and the steady-state power decreases compared to non-insulated. - In areas with insulation, the temperature error between experiment and analysis results is not large. - When flow rate is supplied, there is a large temperature error in experiment and analysis results. - The temperature change after the center of the heater is not large for a temperature change of 15 lpm flow rate. From these results, it can be seen that Solidworks Flow Simulation has a significant difference from the experimental results when there is a flow rate in the tube. This was thought to be because the flow rate acts as a disturbance, and this cannot be sufficiently accounted for in the analysis. In the future, we plan to check whether there is a way to solve this problem.

Considering the domestic situation where all nuclear power plants are located on seaside, the interim storage site is also likely to be located on coastal site. Maritime transportation is inevitable and the its risk assessment is very important for safety. Currently, there is no independently developed maritime transportation risk assessment code in Korea, and no research has been conducted to evaluate the release of radioactive waste due to the immersion of transport cask. Previous studies show that the release rate of radionuclides contained in a submerged transport cask is significantly affected by the area of flow path generated at the breached containment boundary. Due to the robustness of a cask, the breach is the most likely generated between the lid and body of cask. CRIEPI investigated the effect of cask containment on the release rate of radioactive contents into the ocean and proposed a procedure to calculate the release rate considering the socalled barrier effect. However, the contribution of O-ring on the release rate was not considered in the work. In this study, test and analysis is performed to determine the equivalent flow path gap considering the influence of O-rings. These results will be implemented in the computational model to assess sea water flow through a breached containment boundary using CFD techniques to assess radionuclide release rates. To evaluate the release rate as a function of lid displacement, a small containment vessel is engineered and a metal O-ring of the Helicoflex HN type is installed, which is the most commonly used one in transport and storage casks. The lid of containment vessel is displaced in vertical and horizontal direction and the release rate of the vessel was quantified using the helium leak test and the pressure drop test. Through this work, the relationship between the vertical opening displacement and horizontal sliding displacement of the cask lid and the actual flow path area created is established. This will be implemented in the CFD model for flow rate calculation from a submerged transport cask in the deep sea. In addition, the compression of the O-ring causes very small gaps, such as capillaries. In these cases, Poiseuille’s law is used to calculate the capillary flow rate.

Currently, the Korea Atomic Energy Research Institute is conducting research on the development of technology to reduce the disposal area for SF (Spent nuclear Fuel). If the main radionuclides contained in SF can be separated and recovered according to their characteristics (long half-life, high mobility and high heat load) and uranium oxide which is expected to be the final residue, can be made into solids, the burden of the permanent disposal area of the SF will be greatly reduced. The waste form that end up in the repository must be verified for ease of manufacture and stability of the block. And, in order to increase the loading efficiency, a large block manufacturing technology is needed. This study describes the background of introducing PSA (Particle Size Analyzer) which is one of the necessary equipment for manufacturing UO2 blocks using slip casting, the method of using the equipment and performance verification of the equipment using standard samples. The particle size affects the sintering quality by the way the particles rearrange themselves during sintering. Powders of small particles are generally less free flowing and more difficult to compress, they form thin pores between the particles and sinter to higher density. In contrast, larger particle has a lower sintered density. Therefore, accurate particle size measurement and the selection of a suitable particle size are important. For this purpose, a PSA was installed in nuclear cycle experiment research center. To verify the performance of the equipment, a standard sample of 1.025 μm was analyzed. We got an average particle size of 1.0293 μm and standard deviation of 0.0668 μm. This value was within the uncertainty(±0.018 μm) of the sample’s certificate. In the future, this equipment will measure the size of UO2 (depleted uranium) powder and to produce large scale uranium oxide blocks.

Pyroprocessing technology has emerged as a viable alternative for the treatment of metal/oxide used fuel within the nuclear fuel cycle. This innovative approach involves an oxide reduction process wherein spent fuel in oxide form is placed within a cathode basket immersed in a molten LiCl-Li2O salt operating at 923 K. The chemical reduction of these oxide materials into their metallic counterparts occurs through a reaction with Li metal, which is electrochemically deposited onto the cathode. However, during process, the generation of Li2O within the fuel basket is inevitable, and due to the limited reduction efficiency, a significant portion of rare earth oxides (REOx) remains in their oxide state. The presence of these impurities, specifically Li2O and REOx, necessitates their transfer into the electrorefining system, leading to several challenges. Both Li2O and REOx exhibit reactivity with UCl3, the primary electrolyte within the electrorefining system, causing a continuous reduction in UCl3 concentration throughout the process. Furthermore, the formation of fine UO2 powder within the salt system, resulting from chemical reactions, poses a potential long-term operational and safety concern within the electrorefining process.Various techniques have been developed to address the issue of UO2 fine particle removal from the salt, utilizing both chemical and mechanical methods. However, it is crucial that these methods do not interfere with the core pyroprocessing procedure. This study aims to investigate the impact of Li2O and REOx introduced from the electrolytic reduction process on the electrorefining system. Additionally, we propose a method to effectively eliminate the generated UO2 fine powder, thereby enhancing the long-term operational stability of the electrorefining process. The efficiency of this proposed solution in removing oxidized powder has been confirmed through laboratory-scale testing, and we will provide a comprehensive discussion of the detailed results.

Molten salt reactor (MSR) uses fluoride or chloride based molten salt as a coolant of the system, and fuel materials are dissolved in the molten salt, therefore it can be act as both coolant and nuclear fuel. A few issues have arisen from early-stage research and development program of MSR from Oak Ridge National Laboratory, including corrosion of structural materials and fission product management. For investigating the effect of additives on corrosion of structural materials, Mg(OH)2 and MgCl2*6H2O are added into the NaCl-MgCl2 eutectic salt. Prepared chloride salt is injected into the autoclave in the glove box, as well as corrosion coupons for candidate structural materials for molten chloride salt reactor, SS316, Alloy 600, and C-276 are also prepared. The temperature is set as 700°C. After 500 h corrosion experiment, the samples are taken out from the autoclave, and they are analyzed with scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). SS316 samples show weight loss with all salt conditions, while Alloy 600 and C-276 show weight gain after the corrosion experiment.

The Republic of Korea (ROK), as a member state of the IAEA, is operating the State’s System of Accounting for and Control (SSAC) and conducting independent national inspections. Furthermore, an evaluation methodology for the material unaccounted for (MUF) is being developed in ROK to enhance capabilities of national inspection. Generally, physical and chemical changes of nuclear material are unavoidable due to the operating system and structure of facilities, an accumulation of material unaccounted for (MUF) has been issued. IAEA developed statistical MUF evaluation method that can be applied to all facilities around the world and it mainly focuses on the diversion detection of nuclear materials in facilities. However, in terms of the national safeguard inspection, an evaluation of accountancy in facilities is additionally needed. Therefore, in this research, a new approach to MUF evaluation is suggested, based on the Guide to the Expression of Uncertainty in Measurement (GUM) that an evaluation of measurement uncertainty factors is straightforward. A hypothetical list of inventory items (LII) which has 6,118 items at the beginning and end of the material balance period, along with 360 inflow and outflow nuclear material items at a virtual fuel fabrication plant was employed for both the conventional IAEA MUF evaluation method and the proposed GUM-based method. To calculate the measurement uncertainty, it was assumed that an electronic balance, gravimetry, and a thermal ionization mass spectrometer were used for a measurement of the mass, concentration, and enrichment of 235U, respectively. Additionally, it was considered that independent and correlated uncertainty factors were defined as random factors and systematic factors for the ease of uncertainty propagation by the GUM. The total MUF uncertainties of IAEA (σMUF) and GUM (uMUF) method were 37.951 and 36.692 kg, respectively, under the aforementioned assumptions. The difference is low, it was demonstrated that the GUM method is applicable to the MUF evaluation. The IAEA method demonstrated its applicability to all nuclear facilities, but its calculated errors exhibited low traceability due to its simplification. In contrast, the calculated uncertainty based on the GUM method exhibited high reliability and traceability, as it allows for individual management of measurement uncertainty based on the facility’s accounting information. Consequently, the application of the GUM approach could offer more benefits than the conventional IAEA method in cases of national safeguard inspections where factor analysis is required for MUF assessment.

Characteristics and useful effects for human health of antioxidant carbon nanodots contained in microwave-assisted Opuntia humifusa extract (MA-OHE(CD)) were investigated in this work. MA-OHE(CD) was characterized using transmission electron microscopy, dynamic light scattering analysis, X-ray diffraction, UV–vis spectroscopy, X-ray photoelectron spectroscopy, and Fourier transform-infrared spectroscopy. Besides, total phenolic content and antioxidant activity of MA-OHE(CD) were measured. It was revealed that the MA-OHE(CD) increases aquaporin-3 expression in human epidermal keratinocytes cell with hydrophilic characteristics. Moreover, the bio-active compound extraction efficacy and antioxidant activity of microwave-assisted extraction were great when compared to maceration.

In this study, Bacillus velesensis TJS119, isolated from freshwater, demonstrated growth inhibition against insect pathogenic fungi. The culture medium of the B. velezensis TJS119 strain underwent sequential fractionation with n-hexane, chloroform, ethyl acetate, n-butanol, and water. Notably, the n-butanol fraction exhibited significant antifungal activity against Metarhizium anisopliae and Beauveria bassiana. LC/MS analysis of antifungal peaks identified the production of various lipopeptides by B. velezensis TJS119, including two types of iturin A (C14, C15), four types of fengycin A (C14, C15, C16, C17), and two types of fengycin B (C16, C17). The antifungal efficacy of Iturin A and Fengycin against insect pathogenic fungi was further validated using the paper disc diffusion method. These findings underscore the potential of B. velezensis TJS119 as a promising candidate for future research and applications in the realm of agricultural biological controls against fungal diseases.

Protaetia brevitarsis seulensis larvae from industrial insects are traditionally recognized as functional health foods in South Korea. We evaluated the immuno-modulatory effects of feeding beneficial microorganism (Bacillus velezensis TJS119) to P. brevitarsis larvae as a dietary source. In this study, we investigated the immune-enhancing activities of P. brevitarsis larvae hot-water extract (PLW) and PLW after treatment with B. velezensis TJS119 (PLWB) using the RAW 264.7 macrophage cell line. We examined the effects of PLWB on cell proliferation, cytokine production, and nitric oxide production in RAW264.7 cells. PLWB showed no cytotoxicity at concentrations ranging from 7.8 to 1,000 μg/mL in RAW264.7 cells. Treatment with PLWB increased the production of nitric oxide and pro-inflammatory cytokines [tumor necrosis factor-alpha (TNF-α), interleukin-6 (IL-6), and interleukin-1β (IL-1β)] at doses of 62.5 to 1,000 μ g/mL in RAW264.7 cells. As a result, PLWB exhibited a stronger immune-enhancing effect compared to PLW. In conclusion, the results of this study offer experimental evidence to support the potential utilization of PLWB as an immunity-enhancing nutraceutical ingredient.

Bacillus velezensis TJS119 was isolated from the freshwater, and antagonistic activity against of pathogenic fungi. Strain TJS119 showed a broad spectrum of antagonistic activities many fungal pathogens, including the green muscardine fungus Metarhizium anisopliae. The whole-genome sequence of B. velzensis TJS119 was analyzed using the illumina platform. The genome comprises a 3,809,913 bp chromosome with a G + C content of 46.43%, 3,834 total genes, 10 rRNA and 73 tRNA genes. The genome contained a total of 8 candidate gene clusters (difficidin, fengycin, bacillaene, macrolactin, bacillibactin, bacilysin, surfactin and butirosin) to synthesize secondary metabolite biosynthesis. Overall, our data will aid future studies of the biocontrol mechanisms of B. velezensis TJS119 and promote its application in insect disease control.

먹노린재의 방제시기 설정을 위하여 서식지 내 발생 양상을 조사하였다. 전라남도를 중심으로 돌발 대량 발생 한 먹노린재의 발생 조사는 2023년도 벼의 모내기가 완료된 시점부터 전남 곡성군 석곡면과 여수시 화양면 일대 의 친환경단지에서 주 1회 실시하였으며, 벼의 수확이 완료되는 시점까지 진행될 예정이다. 금년도 발생 조사 결과는 지난 2021년도 결과와 비교하여 분석하고자 하였다. 현제까지의 결과, 여수시의 친환경단지 내 먹노린재 의 발생은 모내기가 완료된 이 후 2주 경과 시점에서 발견되었으며, 곡성군은 4주 경과 시점에서 발견되었고, 발생 최고점은 여수시의 경우 모내기 후 6주 경과 시점으로, 곡성군의 경우 5주 경과 시점으로 나타났다. 먹노린재 의 대발생이 지속되던 2021년도의 결과와 비교하였을 때, 2023년도 결과도 유사한 것으로 나타났다. 이에 따라, 먹노린재 친환경제재 살포 시기는 모내기 후 2주 경과 시점이 적절한 것으로 나타났으며, 2차 방제 시점에 대해서 는 추가 조사를 통해서 제안하고자 한다.

Pine Wilt Disease (PWD) is a disease causing mass deaths of pine trees in South Korea, and the dead trees serve as breeding grounds for insect vectors responsible for spreading the disease to other host trees. Because the PWD requires early monitoring to minimize its damage on domestic forestry, this study aims to develop a species distribution model for predicting the potential distribution of PWD by using artificial neural network (ANN) with time-series data. Among the architectures, the Convolutional Neural Network exhibited the highest performance, achieving a validation accuracy of 0.854 and a cross-entropy loss of 0.401, and the InceptionTime model emerged as the second-best performer. This study identified the best-performing ANN architecture for a spatiotemporal evaluation of PWD occurrence, emphasizing the importance for determining hyperparameters with ecological characteristics and data types to apply deep learning into SDMs.

Fall armyworm Spodoptera frugiperda (Lepidoptera: Noctuidae) is a polyphagous agricultural pest that damages about 80 species of plants. It mainly damages Poaceae and plants used as food resources for humans. Its original habitat is the American continent, but it unintentionally settled in tropical and subtropical Asia, including Africa, India, and Sri Lanka. It occurs every year even in southern China, which is geographically adjacent to the Korean Peninsula, causing damage to crops. In Korea, it was first discovered on Jeju Island in June 2019 and is being discovered every year in Jeju and some inland areas. In 2023, there were a total of 13 discoveries, including those in the Jeju and Jeonbuk regions. Quarantine agency identified the maternal genotypes of all currently discovered individuals using COI and identified differences in genetic traits between individuals using the sex-related Z-chromosome. For comparison with the information on the individuals that invaded the country, 15 individuals from Guangxi and Guangdong provinces in China were collected and secured. Through the analysis of overseas samples, a database has been added to compare genetic information with domestic invasive species, and the reliability of the analysis is expected to increase.

Solenopsis invicta, known as the red imported fire ant, is an insect native to South America. This species was unintentionally introduced into Australia, New Zealand, several Asian countries, Caribbean countries, and the United States. It shows a high survival rate and settlement potential in human-habitable and non-living areas such as tropical rainforests, disturbed areas, deserts, grasslands, and roads. In Korea, invasions of red fire ants have been reported every year since 2017, and two invasions were discovered in 2023. Quarantine agency analyzing the haplotype and colony social type of S. invicta for surveillance and control. Population genetic analysis using Microsatellite Alleleic data of 66 loci to trace the origin of the invasion. Through research cooperation with the United States Department of Agriculture (USDA), we have received samples and expanded our genetic information database. This study analyzed genetic differences between 15 invasive populations and 44 reference groups. As a result of microsatellite analysis, the domestic invasive population showed a genetic structure similar to those in Guangzhou, China, and Florida, USA.

Anoplophora horsfieldii (Hope, 1843), 국명 노랑알락하늘소(가칭)는 아열대 지역에 주로 분포하는 종으로 2019 년에 제주도 용연계곡에서 처음 발견되었으며, 2023년에 국내 정착이 보고되었다. 국내에서는 팽나무에서 발생 하는 것으로 알려졌으나, 섭식방식, 산란 선호성 등 생태적 특성에 대해서는 국내외 연구가 전무하다. 따라서 본 연구에서는 노랑알락하늘소의 기초적인 생태정보를 제공하고자 실내 산란 선호성 조사 및 야외조사를 진행 했다. 산란 선호성 실험은 기주식물로 알려진 팽나무, 멀구슬나무와 제주도내 대표 수종인 동백나무, 종가시나무 을 대상으로 했다. 이 중 팽나무에서만 산란이 확인었으며, 상대적으로 굵은 팽나무에서 더 많은 산란이 확인되었 다. 야외조사에서는 최대 발생지인 용연계곡을 기준으로 반경 3 km 내에서 노랑알락하늘소의 탈출공이 확인된 32 그루의 팽나무를 대상으로 피해를 조사하였다. 나무의 굵기는 흉고직경이 20-40 cm인 팽나무에서 탈출공이 많이 확인되었고, 높이는 지면으로 부터 0-100 cm 구간에서 가장 많은 탈출공이 발견되었다.

Riptortus pedestris has established symbiotic interactions with specific bacteria from soil environment in every generations. The soil environment is extremely heterogeneous with microbial diversity, suggesting that bacterial composition of the R. pedestris can be affected by surrounding environments. Therefore, we investigated spatiotemporal variation of bacterial communities in wild R. pedestris collected from five mainland areas and Jeju Island in South Korea across insect generations. Among the 390 R. pedestris adults collected, we detected a total of 28 bacterial genera from the symbiotic region of insects. Among the bacterial genera, genus Caballeronia bacteria was the most abundantly detected regardless of sampling site and generation. Nevertheless, bacterial richness varied among the insect generations with 10 genera detected in overwintered generation, 15 genera in the 1st generation and 18 genera in the 2nd generation. Moreover, we found five bacterial genera that were exclusively detected from the Jeju island compared to the mainland areas surveyed.

Nutrient acquisition by insect herbivores affect all aspect of the the lifespan of individauls. For seed-sucking insect herbivores, they face challenges with nutrient acquisition due to requirement for extra-oral digestion of seed contents into a readily-ingestible state. In this study, we demonstrated environmentally-transmitted Caballeronia insecticola allow seed-sucking R. pedestris to overcome challenges with extra-oral digestion. Through the evaluation, first, we found symbiotic insects exhibited enhanced feeding efficiency by consuming significantly larger amount of food per feeding attempt compared to apo-symbiotic insects (P<0.05). Then, we observed feeding behavior modification in the symbiotic insects from the behavior tracking evaluation. Symbiotic insects displayed dichotomic behavior which can be generally divided into early focused feeding and later subdued resting periods. By contrast, apo-symbiotic insects displayed unordered behavior by frequent switches between feeding and walking behavior.

사막이리응애(Neoseiulus californicus)는 칠레이리응애에 비하여 고온건조한 조건에서 유리하고 점박이응 애, 차응애, 차먼지응애 등 응애류 뿐만 아니라 가루이, 총채벌레 등 다양한 미소해충을 포식 포식하는 광식성 천적으로서 전세계적으로 산업화되고 있다. 사막이리응애를 농가수준에서 증식하기 위하여 간단한 대량생산 방법을 개발하였다. 천적의 먹이원인 가는다리고기진드기와 배지로서 밀기울(70%) 및 팽창질석(30%)을 멸균 팩에 넣고 사막이리응애를 사육하였다. 그 결과 사막이리응애의 밀도는 3주차에 18배로 증식되었다. 증식된 사막이리응애를 딸기 농장에 2월초부터 4월초까지 8주간 매주 투여한 결과 잎당 점박이응애의 밀도는 무처리구 에서 41.5마리이고 천적처리구는 7.0마리로서 점박이응애 방제효과가 83%로 나타났다. 본 연구를 통하여 자가 생산한 사막이리응애를 활용하여 딸기농가의 점박이응애 방제에 효과적으로 사용할 수 있을 것으로 판단된다.

경북대학교 친환경농업연구센터에서는 농업인들의 효과적인 천적 활용을 증진시키기 위하여 2016년부터 경상북도 농민사관학교의 지원을 받아서 친환경천적 교육과정을 개설하고 천적 자가생산 및 현장적용 기술의 실습교육을 실시하였다. 그동안 토양 포식성 천적인 총채가시응애(Gaeolaelaps aculeifer)와 뿌리이리응애 (Stratiolaelaps scimitus), 그리고 점박이응애의 포식성 천적인 칠레이리응애(Phytoseiulus persimilis)와 사막 이리응애(Neoseiulus californicus)의 간편하고 경제적인 대량생산기술을 개발하고 그 기술을 약 180명의 농업 인에게 전수하였다. 즉, 농업인들이 스스로 천적을 자가생산하여 시설재배지에 적용함으로서 비용절감 및 청정 농산물 생산 효과를 높히는데 기여했다. 또한, 간편한 천적생산기술을 전국적으로 농업기술원, 농업기술센터, 그리고 친환경농업인단체 등 20여개 기관에 전수하였다. 최근, 경북의 농업기술센터(안동, 고령, 경주)에서 농업 인을 대상으로 천적 대량생산 시스템 보급 시범 사업을 실시하면서 뿌리이리응애 및 칠레이리응애 등의 천적 자가생산시설을 구축하고 자체적으로 생산함으로서 지속적인 천적 활용이 가능하게 되고 해충 방제 효과를 증가시킬 수 있었다. 즉, 농업인들이 직접 천적을 생산하고 활용하게 함으로서 천적농업의 성공사례가 증가하였 을 뿐만 아니라 국내 천적 공급 시스템이 다양화되어 천적농업의 활성화에 크게 기여한다고 판단한다.

경북 안동의 진걸맘농장은 딸기와 쪽 농사를 주로 하고 있으며 10년 이상 친환경 무농약 농법을 인증받은 농가로서 천적을 활용하여 토경 1,000평 규모의 시설 하우스에 딸기 재배를 하고 있다. 2018-2020에 경북농민사관학교 친환경 천적과정을 통하여 천적의 자가생산 기술을 배우고 2021년부터 농가에서 직접 자가생산을 시작하였다. 그래서, 진걸맘농가는 칠레이리응애를 자가사육하여 지속적으로 딸기 재배지에 처리함으로서 점박이응애 방제에 성공한 농업인으로서 국내 첫 사례로 꼽힌다. 또한, 2022년 안동시농업기술센터에서 안전농산물 생산을 위한 천적 배양시 스템 보급 시범 사업에 선정되어 딸기 해충의 생물적 방제를 위한 뿌리이리응애, 칠레이리응애, 보리뱅커플랜트 등의 천적 배양시설 완공, 천적의 자가생산 및 성공적인 현장적용 기술로서 농산물의 지역특화, 브랜드화를 통한 농산물 가격 차별화에 크기 기여하였으며 국내 천적농업의 발전을 위해 앞장서고 있는 선도농가로 인정받고 있다.