본 연구에서는 연료극 또는 공기극에 함유된 불순물인 황화합물의 도입을 차단할 수 있는 GDL을 제조하여, 이를 평가용 단위전지에 체결하여 H2S와 SO2를 연료극과 공기극에 각각 동시에 공급하여 PEMFC의 성능 저하 및 회복에 관한 연구를 수행하였다. 그 결과 H2S와 SO2의 농도가 증가함에 따라 전지의 성능이 감소하며 특히 10 ppm 이상의 농도에서는 10분 이내에 약 10-15% 정도 성능이 감소하였다. 특히 GDL 표면의 기공이 없는 CN-2 GDL을 체결한 단위전지의 경우 피독에 의한 성능 감소 속도가 더 빠른 것을 확인하였다. 그리고 단위전지 피독 후 황화합물이 혼합되지 않은 순수 가스를 1시간 이상 공급하였을 때 전지의 성능이 GDL의 종류에 따라 90%에서 95% 이상 회복되며 CN-1 GDL의 경우가 가장 회복이 우수하였다.

고분자 전해질막 연료전지는 연료극의 연료와 공기극의 공기에 각각 H2S와 SO2이 포함되어 있을 때 그 성능이 심각하게 감소한다. 본 연구는 고분자전해질막 연료전지의 공기극과 연료극에 1 ppm에서 10 ppm의 불순물 가스를 공급하여 전기적 성능측정을 통해 복합적인 황불순물이 단위전지에 미치는 영향을 확인하였다. 최적의 운전조건에서 불순물가스를 피독하였을 때 SO2와 H2S의 농도가 증가할수록 성능이 급격히 감소하였다(단위전지 온도 65℃, 상대습도 100%). 그리고 황의 흡착은 MEA의 백금 촉매층 표면서 일어나며, 불순물 가스가 MEA에 누적되는 것을 확인하였다. 1, 3, 5, 및 10 ppm 4회의 연속적인 피독 후 연료전지의 성능이 0.71 V에서 0.54 V(76 %)로 감소하였다.

황화수소가 고분자 전해질막 연료전지의 연료극에 공급되었을 때 전지 성능의 저하와 황화수소 피독 후 순환전류 전압법(CV) 스캔을 통해 전지의 성능 회복에 관한 연구를 수행하였다. 수소에 30 ppm의 황화수소를 희석하여 연료극에 공급하고 전류밀도를 0.5A/cm2로 고정하여 1시간 동안 3차례 피독한 후 CV를 5회 스캔하여 단위전지의 성능회복을 확인한 결과 피독 전 단위전지의 초기 성능은 0.60 V에서 1.16A/cm2이였으며, 30 ppm의 황화수소를 한 시간 동안 피독한 결과 0.77A/cm2로 그 성능이 감소하였고, 피독 횟수가 증가함에 따라 성능이 0.57 V까지 감소하였다. 그리고 황화수소 피독 후 각 스텝에서 CV 스캔을 5회 실시하였을 때 단위전지의 성능이 90.3%까지 회복하는 것을 알 수 있었다. 또한, 황화수소 피독 후 단순히 고순도의 수소 가스만 연료극에 주입하여도 약 80% 정도의 성능회복이 가능하였다. 이러한 현상으로 판단할 때 황화수소 가스의 백금 촉매층에의 흡착은 그리 강하지 않음을 알 수 있었다.

완전 생분해성 고분자 블렌드필름을 제조하기 위하여 치환도가 다른 두 셀룰로오스 아세테이트(CA)에 5 - 50%의 저분자량 폴리락타이드(PLA)를 블렌딩하였다. 이 때 사용된 각각의 고분자는 10% 메탄올/메틸렌클로라이드 혼합용제에 녹여서 점도가 같은 조건의 농도로 제조하였다. 각 조성의 블렌드필름의 표면 모폴로지와 열적 성질, 기계적 성질을 조사하였다. 화학적 구조는 적외선 분광법으로 확인하였으며, 전자현미경을 통한 표면 분석 결과 5% 이하의 폴리락타이드를 함유한 블렌드필름은 상분리가 거의 일어나지 않았으며 20% 이상이 함유된 경우 상분리가 매우 심각하였다. 또한 블렌드필름의 인장강도는 셀룰로오스 아세테이트의 함량이 늘어날수록 TAC/PLA의 경우 820kgf/cm2 및 DAC/PLA의 경우 600kgf/cm2까지 향상시킬 수 있었다.

금속 주조시 사용되는 탄소이형제를 카본블랙과 점증제 겸 알데하이드 화합물의 경화제로 사용될 수 있는 수용성 고분자인 잔탄검(X-gum), 카르복시메틸셀룰로오스(CMC)을 혼합하여 제조하였다. 이 때 카본블랙의 안정한 분산을 위하여 0.25 wt%의 X-gum 또는 1.0 wt%의 CMC가 적당하였다. 1.0 wt% 보다 낮은 농도의 CMC를 사용했을 경우 카본블랙이 매우 쉽게 층분리되었다. 유리판에 대한 부착력은 경화제와, 구르탈알데하이드 및 사슬연장제인 올리고당의 양에 비례하였으며. X-gum으로 제조된 탄소 이형제는 CMC를 이용해 제조된 것보다 유리에 대한 부착력이 우수하였다. 결과적으로 본 실험의 최적 조건에서 제조된 탄소이형제는 친환경적으로 주조시에 적용할 수 있을 것으로 판단된다.

Polymer electrolyte membrane fuel cell (PEMFC) performance degrade when sulfur dioxide is present in the fuel hydrogen gas, this is referred as SO2 poisoning. This paper reveals SO2 poisoning on PEMFC cathode part by measuring electrical performance of single cell under 1 ppm and 5 ppm on SO2 gas operating. The security of SO2 poisoning depended on SO2 concentration under the best operating conditions(65℃ of cell temperature and 100% of relative humidity between anode and cathode). SO2 adsorption occured on the surface of catalyst layer on membrane electrode assembly (MEA), In addition, MEA poisoning by SO2 was cumulative but reversible. After poisoning within 5 ppm SO2 for 1hr, the electrical performance of PEMFC was found to recover up to about 93% by cyclic voltametry scan.

Alloys of nylon(PA6) and ethylene-propylene-diene polymer, modified with maleic anhydride(MEPDM) were prepared using a melt kneading process. This study focuses on the effects of the content of MEPDM in PA6 blend on the mechanical and thermal properties of such blends where MEPDM is the dispersed phase. Mechanical properties were examined by stress-strain measurements and impact strength test. Both impact strength of PA6/MEPDM at room temperature and at -20℃ were improved up to 400-550% with the amounts of MEPDM. However, PA6/MEPDM containing 3-5 wt% of MEPDM showed the about 700kgf/m2 of the maximum tensile strength but 8.5 % of the lowest elongation. For certain compositions of PA6 with rubbery MEPDM, the interesting reduction of elongation is caused by the reaction of the polyamide amine end groups with maleic anhydride portion in MEPDM, that provided a reinforcement in the PA6 matrix. In addition, the introduction of antistatic agent on the surface of alloys causes significant reduction of their surface electrostatic resistance.

Polymer electrolyte membrane fuel cell (PEMFC) performance degrades when hydrogen sulfide (H2S) is present in the fuel hydrogen gas; this is referred to as H2S poisoning. This paper reveals H2S poisoning on PEMFC by measuring electrical performance of single cell FC under various operating conditions. The severity of H2S poisoning depended on H2S concentration under best operating conditions(65℃ of cell temperature and 100% of anode humidification). H2S adsorption occured on the surface of catalyst layer on MEA, but not on the gas diffusion layer(GDL) by analyzing SEM/EDX data. In addition, MEA poisoning by H2S was cumulative but reversible. After poisoning for less than 150 min, performance of PEMFC was recovered up to 80% by just inert nitrogen gas purging.

In this research, an effective method for reducing the fibrillation of lyocell fibers, which are spun from a solution of cellulose in N-methyl morpholine-N-oxide(NMMO), through consecutive chemical treatments. Undried solution-spun cellulosic fiber was firstly treated with 10 to 30 wt% of multifunctional crosslinking agents, such as ethylene glycol poly(3-chloro-2-hydroxypropyl) ether, and then dipped into alkaline solution to introduce epoxy functions. Finally steam condition was applied to occur a chemical crosslinking in order to reduce the fibrillation on the surface of fibers. Fibrillation was also reduced significantly by adding extra Na2SO4 in NaOH solution. In addition, Antifibrilllated lyocell fibers show the slightly higher dyeability(4 %) to Cibacron Blue without serious reduction of mechanical properties.

Ultraviolet curable coating solution was prepared with poly(ethylene glycol) acrylate oligomer and various mono and multi-functional acrylate monomers. The optical properties of UV cured coating layer on PET film with acrylate coating solution containing metal oxides, such as fumed silica and alumina, were also investigated to reduce light reflection on films. Poly(ethylene glycol) diacrylate which has 575 of average molecular weight was used as oligomer acrylate, and pentaerythritol triacrylate and dipentaerythritolpenta-/hexa acrylate were used as multi-functional acrylate monomers. Also, butyl acrylate was used to improve the adhesion as well as to reduce glass transition temperature to give a better flexability. 1-hydroxy cyclohexyl phenyl ketone was used as photoinitiator. We found out the metal oxides in acrylate coating solution showed a homogeneous dispersion from energy dispersive spectroscopy data. Transmittance and light reflection of coated PET film was measured with UV/vis spectrometer and gloss meter, respectively. When 1.00 g of both metal oxides was added into coating solution, the transmittance and the glossiness were reduced from 90% to 30% and from 190 GU to 35 GU, respectively. However, adding up to 1.00 g of the metal oxide into coating solution did not affect on the hardness of coating layer and adhesion between coated layer and PET film. Conclusively, we can control transmittance and light reflection of coated film by adjusting the amounts of metal oxide in coating solution.

The acrylic coating emulsions were prepared by the emulsion polymerization to protect the surface of steel plate from the corrosion chemicals like acid, base and salt water. MMA(methyl methacrylate), styrene, BA(butyl acrylate), and 2-HEMA(2-hydroxyethyl methacrylate) were used as monomer. KPS(potassium persulfate) and SBS(sodium bisulfite) as redox initiator and SDBS(sodium dodecylbenzene sulfonate) as emulsifier were used on the emulsion polymerization reaction. The most stable in-situ coating was obtained when 10% of MMA was added. Both particle size and quantity in emulsion were decreased as increasing the mount of SDBS. the most stable prepared coating emulsion with polyisocyanate crosslinker showed very high anticorrosion properties on the coated steel layer to salt water, whereas no significant improvement of anticorrosion property to acdic and basic condition it showed.

Methyl methacrylate(MMA) was grafted onto microcrystalline cellulose(MCC) with ceric ammonium nitrate(CAN) as a redox initiator at the various conditions. The cellulose triacetate(CTA) composite films added MCC and MMA-grafted MCC powders were prepared on a glass plate. The graft yield(GY) and graft efficiency(GE) of the grafted MCC were calculated with the simple equations by the weight balance method. The double bond of C=O on the grafted MCC surfaces was confirmed by the fourier transform infrared spectroscopy with attenuated total reflection(FT-IT ATR) spectrophotometer. After grafting, the degree of crystallinity of cellulose powders was decresed by judging from x-ray diffraction(XRD) data. Scanning electron microscope(SEM) photos showed the only solvent and CAN solution could change the roughness of MCC powders and the effect of powder dispersions in composite matrix. The tensile strength of MCC/CTA composite films was decreased with increase of MCC powder contents. When 5% grafted MCC was added, the tensile strength of grafted MCC/CTA composite films was increased from 82.3 MPa to 97.2 MPa. The thermal property of powders was also analyzed by the thermogravimetric analysis(TGA).