This study aims to optimize the cochlea-inspired artificial filter bank (CAFB) using El-Centro seismic waveforms and test its performance through a shaking table test on a two-span bridge model. In the process of optimizing the CAFB, El-Centro seismic waveforms were used for the purpose of evaluating how they would affect the optimizing process. Next, the optimized CAFB was embedded in the developed wireless-based intelligent data acquisition (IDAQ) system to enable response measurement in real-time. For its performance evaluation to obtain a seismic response in real-time using the optimized CAFB, a two-span bridge (model structures) was installed in a large shaking table, and a seismic response experiment was carried out on it with El-Centro seismic waveforms. The CAFB optimized in this experiment was able to obtain the seismic response in real-time by compressing it using the embedded wireless-based IDAQ system while the obtained compressed signals were compared with the original signal (un-compressed signal). The results of the experiment showed that the compressed signals were superior to the raw signal in response performance, as well as in data compression effect. They also proved that the CAFB was able to compress response signals effectively in real-time even under seismic conditions. Therefore, this paper established that the CAFB optimized by being embedded in the wireless-based IDAQ system was an economical and efficient data compression sensing technology for measuring and monitoring the seismic response in real-time from structures based on the wireless sensor networks (WSNs).

In this study, SMG(Smart Material with Grease) was developed, which was improved the precipitation minute particle in grease during long term standstill. Also, small-sized cylinder damper equipped with an electromagnet in a piston was developed for using a performance evaluation of the damper with SMG and the dynamic load test, and damping force using Power model and Bingham model was derived in order to compare to the result of that of the damper. The data obtained from the dynamic load test were analyzed and plotted, and then a dynamic range was calculated to evaluate the usability of the damper with SMG. The performance of the damper with SMG was compared to the damping forse derived from the Power and Bingham model. The result of this evaluation shown that the usability of SMG damper was demonstrated by this test as a semi-active controlling equipment of small-sized damper.

This research focuses on developing the Smart material with Grease adopted as a base oil to overcome a particle deposition caused by the MR fluid consisting of a silicon, which maximizing the characteristics and advantage of the MR fluid. By adopting the SMG fluid to a shear damper, this paper aimed to evaluate the control performance of it according to the variation of intensity of electric current(0 A, 0.5 A, 1.0 A, 1.5 A, 2.0 A, 2.5 A) and frequency(0.5 Hz, 1 Hz, 2 Hz). Subsequently, the usability of the SMG damper was analyzed by comparing the dynamic model of it to that of the other types of dampers(Power(Involution) Model, Bingham Model). As a result, DR, the performance indicator of semi-active damper, shows approximately 5 in a condition of 2 Hz. Also while confirming the excellent performance like the Power and the Bingham model, it raises the possibility to exploit it as the semi-active damper.

This study experimentally and analytically examines the seismic vulnerability of steel rack storage frames subjected to Korea earthquakes (2016 Gyeongju earthquake and 2017 Pohang earthquake). To achieve this aim, this study selects a three-story, one-bay steel rack frame with a typical configuration of rack frame in Korea. Firstly, the local behavior for frame components is examined by performing monotonic and/or cyclic load tests and the global response and dynamic characteristics of the subject rack frame are investigated by conducting a shaking table test. The analytical model of the rack frame is then created based on the experimental results and is used to perform nonlinear time history analyses with recorded Korea earthquakes. The seismic demand of the rack frame is considerably affected by the spectral acceleration response, instead of peak ground accelerations (peak floor accelerations). Moreover, the collapse fragility curve of the rack frame is developed using incremental dynamic analyses for the Gyeongju and Pohang earthquakes. Fragility results indicate that the ground motion characteristics of these earthquakes do not significantly affect the frame vulnerability at the collapse state.

In this paper, an experimental study was carried out for vibration control of cable bridges with structurally flexible characteristics. For the experiment on vibration control, a model bridge was constructed by reducing the Seohae Grand Bridge and the shear type MR damper was designed using the wind load response measured at Seohae Grand Bridge. The shear type MR damper was installed in the vertical direction at the middle span of the model bridge, and dynamic modeling was performed using the power model. The tests of the vibration control were carried out by non-control, passive on/off control and Lyapunov control method on model bridge with scaled wind load response. The performance of the vibration control was evaluated by calculating absolute maximum displacement, RMS displacement, absolute maximum acceleration, RMS acceleration, and size of applied power using the response (displacement, acceleration, etc.) from the model bridge. As a result, the power model was effective in simulating the nonlinear behavior of the MR damper, and the Lyapunov control method using the MR damper was able to control the vibration of the structure and reduce the size of the power supply.

In the case where a MR-damper is employed for vibration control, it is important to decide on how much control capacity should be assigned to it against structural capacities (strength and load, etc). This paper aims to present a MR-damper's control capacity suitable for the capacities of the structure which needs to be controlled. First, a two span bridge was built equipped with a MR-damper, which constitutes a two-span MR-damper control system. Then, inflicting an earthquake load on the system, a basic experiment was performed for vibration control, and a simulation was also carried out reflecting specific control conditions such as MR-damper and rubber bearing. The comparison of the results against each other proved their validity. Then, in order to calculate an optimal control capacity of the MR-damper, structural capacity was divided into eleven cases in total and simulated. For each case, an additional load of 30 KN was inflicted everytime, thereby increasingly strengthening structural capacity. As a result of the study, it was found that the control capacity of MR-damper of 30 KN was safely secured only with lumped mass of more than 150 KN(case 6). Therefore, it is concluded the MR-damper showed the best performance of control when it exerted its capacity at around 20% of structural capacity.

This paper is concerned with an experimental research to control of random vibration caused by external loads specially in cable-stayed bridges which tend to be structurally flexible. For the vibration control, we produced a model structure modelled on Seohae Grand Bridge, and we designed a shear type MR damper. On the center of its middle span, we placed a shear type MR damper which was to control its vibration and also acquire its structural responses such as displacement and acceleration at the same site. The experiments concerning controlling vibration were performed according to a variety of theories including un-control, passive on/off control, and clipped-optimal control. Its control performance was evaluated in terms of the absolute maximum displacements, RMS displacements, the absolute maximum accelerations, RMS accelerations, and the total power required to control the bridge which differ from each different experiment method. Among all the methods applied in this paper, clipped-optimal control method turned out to be the most effective to reduces of displacements, accelerations, and external power. Finally, It is proven that the clipped-optimal control method was effective and useful in the vibration control employing a semi-active devices such MR damper.

This paper introduces a digital image processing(DIP) method as a method for measuring the displacement of pylon. The comparison of DIP results and ANSYS analysis results verified the validity of the image processing technique. Normalized cross-correlation(NCC) coefficient was used and experiments were performed three times. It shows that the displacement difference was 22% and 5% compared to ANSYS results. Therefore, the image processing method is expected to be able to measure the displacement of pylon sufficiently.

이 연구의 목적은 대형 구조불의 상설 감지를 위한 감지기의 최적 위치의 얄고리츰윷 개발하는데에 있다. 구조물 의 진동을 이용한 감지 시 스템은 장기적 으로 계 속해서 구조물을 자동으로 감지하는데에 좋은 방법 증의 하나이다. 하지만 구조물의 진동융 정확히 계측하기 위해서 는 감지기의 위치나 감지기의 숫자에 콘 영향을 받는데， 이와 같은 일은 대형 구조물에 있어서 쉽지가 않다. 최적의 감지기 위치와 최소의 감지기로 가장 정확한 데이터를 획득하기 위하여 최적합한 감지기의 위치를 위한 알고려즘이 개발되어 수치 적 그리고 실험적으로 유용성 을 보인다. EOT가 개발되어 모형 교량에 적용하여 EIM과 비교 분석된다 이 들의 비교를 똥하여， 이 연구에서 제안되어진 EOT가 적 은 수의 감지기로 좋은 걸과를 보여， 상설감지의 복적에 적합함을 보여 준다.

본 연구에서는 압축센싱 기술인 CAFB(달팽이관 원리기반의 인공필터뱅크)가 El-Centro 지진 등 지진상황에서 구조물의 동적응답을 포함한 지진응답을 실시간으로 압축하여 획득할 수 있는지 평가하였다. 최적화된 CAFB를 무선 IDAQ 시스템에 임베디드 하였다. 이를 이용하여 대형 Shaking Table에 설치된 2-span 교량구조물의 지진응답을 실시간으로 압축하여 획득 하였다. 연구결과 압축신호는 원시신호 대비 우수한 응답성능 및 데이터 압축효과를 보였으며 이를 통해 CAFB가 지진상황에서도 구조물의 동적응답을 포함한 지진응답을 실시간으로 압축 획득할 수 있음을 확인하였다.

데이터 병목현상 등의 이유로 대용량의 동적 데이터를 무선으로 계측하여 구조물 건전도 모니터링을 수행하는 데는 한계가 있다. 이에 선행연구에서는 압축센싱 기술인 CAFB(달팽이관-영감형 인공필터뱅크)를 개발하여 무선 압축센싱 성능을 실험적으로 평가하였다. 본 논문에서는 CAFB를 적용한 무선 계측시스템의 유효성 평가를 목적으로 Kobe 지진파형으로 최적화된 CAFB를 이용해 지진응답 실험을 진행하였다. 결과적으로 Kobe 지진파형으로 최적화한 CAFB로 수신한 무선 데이터는 64~91%의 압축률을 보였으며 99% 이상의 재건율로 무선 데이터를 획득하는데 효과적임을 확인하였다.

본 논문에서는 사장교를 지탱하는 주요 부재인 케이블의 손상 위치를 빠르게 검출할 수 있는 손상평가 기술을 개발하고, 모형 교량 손상 실험을 통하여 개발한 기술의 손상평가 성능을 검증하고자 하였다. 손상평가 기술의 개발을 위하여 통계적 패턴 인식 기술인 마할라노비스 거리 이론을 활용하였으며, 복잡한 구조체의 손상위치 판별을 위하여 계측 위치별 획득 데이터의 변동성을 손상평가 기술에 반영하였다. 개발한 기술의 손상평가 성능을 확인하기 위하여 모형 사장교를 대상으로 손상 실험을 진행하였다. 그 결과, 개발한 손상평가 기술은 무손상 상태의 응답과 손상 상태의 응답을 활용하여 사장교 케이블 의 손상 위치를 검출할 수 있는 통계적 패턴을 제공하는 성능을 보이는 것을 확인하였다.

본 논문에서는 가속도계로 측정된 교량 데이터를 딥러닝 기법 모델로 분석하여 교량의 케이블 손상 위치를 예측하는 연구를 진행하였다. 먼저 서해대교 1/200 스케일로 제작된 모형에 8개의 가속도계를 부착, 케이블 위치별 손상 시나리오를 5개로 나누어 해당 케이블을 교량에서 해체했다. 그리고 교량 중심에 일정한 충격을 주어 가속도계로 충격 데이터를 수집하였다. 수집한 데이터 중 70%를 Train set으로 선전하여 딥러닝 모델에 학습시키고, 나머지 30%를 Test set으로 선정하여 모델에 테스트 한 결과 평균 89%의 정확도로 케이블 손상 위치를 예측하였다.

본 논문은 적재설비의 바닥 구속조건에 따른 안전성을 평가하고자 한다. 평가를 위해서 국내에서 일반적으로 사용하고 있는 파렛트랙을 대상구조물로 선정하여 진동대 실험을 진행하였다. 진동대 실험을 위한 적재설비의 바닥 구속조건을 총 4가 지(1 bolt, 2 bolts, 4 bolts, Fixed)로 구분하여 진행하였다. 실험은 인공지진파를 증가시켜가며 진행하였고, 각 층별에서의 변위응답과 영구변형을 비교하였다. 이에 따른 실험 결과, 지진 강도에 따라 기둥 바닥의 구속조건을 달리 적용하는 것이 필요하다.

탄소섬유는 경량이면서 높은 기계적 특성 때문에 우주항공, 선박, 자동차, 토목 및 건축과 같은 산업분야에서 그 어느 때 보다 더 광범위하게 적용되고 있다. 본 연구는 섬유혼입률 및 섬유길이 변화에 따른 탄소섬유 보강시멘트 복합재료( CFRC)의 역학적 특성과 휨 거동을 분석하였으며, 또한 자연 낙하시험에 의한 모르타르 시편에 대한 내충격성을 비교, 검토하였다. 더불어, 탄소섬유(CF)의 혼입률은 0.5%, 1.0%, 2.0% 및 3.0%로 변화를 주었으며, 각각의 섬유길이는 6 mm와 12 mm를 사용 하였다. 실험결과, 플로우 값은 탄소섬유의 뭉침현상으로 인해 유동성 측면에서 매우 불리하였으며, 단위용적질량은 다소 감소하였다. 특히, 압축강도는 탄소섬유 혼입량이 증가함에 따라 감소하는 것으로 나타내었다. 반면 휨 강도는 섬유 길이가 12 mm이고 2% 혼입한 것이 가장 높은 휨 강도를 보였다. 내충격성 시험결과, 보통 모르타르 시편은 완전파괴까지의 낙하횟수가 2∼3회 정도 걸리지만 반면 CFRC 시편은 섬유혼입량이 증가함에 따라 다소 차이가 있지만, 섬유길이가 12 mm이고 섬유혼입량 2% 인 경우 충격에 대한 저항성이 가장 높았다.

In this paper, damage assessment technology based on statistical pattern recognition technology was developed for maintenance of structure and the performance of the developed technology was verified by vibration test. The damage assessment technique uses the improved Mahalanobis distance theory, which is a statistical pattern recognition technique, and developed to take account of the variability between the measured data. In order to verify the damage evaluation performance of the developed technology, a cable damage test was conducted for a cable-stayed bridge. Experimental results show that the developed damage assessment technology has the capability of extracting information that can determine the location of damage due to cable damage.

In this paper, an experimental study on the data compression sensing technique optimized by Northridge earthquake waveform was performed to efficiently obtain the dynamic response of the civil structure. The optimized compression sensing technique is embedded in the wireless sensing system. Also, the dynamic response(acceleration) of the cable-stayed bridge model was acquired and the validity of the compression sensing technique was evaluated. The data compression sensing technique optimized by Northridge earthquake waveform was able to efficiently obtain the dynamic response of a flexible civil structure under 10Hz.

In this paper, an experimental study on the data compression sensing technique optimized by El-centro earthquake waveform was performed to efficiently obtain the dynamic response of the civil structure. The optimized compression sensing technique is embedded in the wireless sensing system. Also, the dynamic response(acceleration) of the cable-stayed bridge model was acquired and the validity of the compression sensing technique was evaluated. The data compression sensing technique optimized by El-centro earthquake waveform was able to efficiently obtain the dynamic response of a flexible civil structure under 10Hz.

In this paper, an experimental study on the data compression sensing technique optimized by Kobe earthquake waveform was performed to efficiently obtain the dynamic response of the civil structure. The optimized compression sensing technique is embedded in the wireless sensing system. Also, the dynamic response(acceleration) of the cable-stayed bridge model was acquired and the validity of the compression sensing technique was evaluated. The data compression sensing technique optimized by Kobe earthquake waveform was able to efficiently obtain the dynamic response of a flexible civil structure under 10Hz.