Periodontal disease (PD) is strongly linked to increased risk of oral squamous cell carcinoma (OSCC); however, the specific mechanism through which the development of PD and OSCC is simultaneously promoted remains unclear. This study explored the impact of periodontal pathogens on OSCC progression and the contribution of periodontal pathogen-stimulated OSCC to PD development. The expression of osteoclastogenesis-inducing factors was assessed using quantitative reverse transcription polymerase chain reaction analysis following stimulation of OSCC with lipopolysaccharide (LPS) derived from the periodontal pathogen Porphyromonas gingivalis (Pg), a pathogen commonly responsible for PD. The cell counting kit-8 assay was used to determine the effects of Pg-LPS on OSCC proliferation and drug resistance to cisplatin and 5-fluorouracil. The effects of conditioned medium (CM) derived from Pg-LPS–stimulated OSCC on osteoclastogenesis was evaluated using tartrate-resistant acid phosphatase (TRAP) staining on bone marrow-derived macrophages (BMMs). Pg-LPS administration in SCC-25 and YD-8 OSCC cell lines induced a significant increase in receptor activator of nuclear factor kappa-B ligand mRNA expression; however, it did not affect cell proliferation. Treatment with CM derived from Pg-LPS–stimulated SCC-25 or YD-8 cells markedly enhanced the formation of TRAP-positive multinucleated cells during osteoclast differentiation of BMMs. Altogether, these findings demonstrate that Pg-LPS–stimulated OSCC promoted osteoclastogenesis through a paracrine mechanism.

We investigated the effects of fluctuating temperature on development and fertility of M. persicae at different temperature conditions, 10, 15, 20, 25, 28, and 30±5℃, respectively. In this study, we collected detailed data on development periods, and fertility of M. persicae at six different temperatures. We analyzed the life table parameters of M. persicae using age-stage, two-sex life table program. The intrinsic and finite rate of increase were the highest at 25±5℃. The fertiltiy was the highest at 20±5℃.

We investigated the functional response of aphid parasitoid, Aphidius colemani Viereck (Hymenoptera: Braconidae), on the green peach aphid, Myzus persicae (Sulzer) (Hemiptera: Aphididae) at four different constant temperatures (15, 20, 25 and 30℃). Seven host densities (2, 4, 8, 16, 32, 64, and 128) were used during a 24-h period. A type III functional response for A. colemani was fit separately at each constant temperature. The estimated handling times at 15, 20, 25, and 30℃ were 0.85, 0.61, 0.41 and 0.88 day, respectively. The proportion of aphids that were parasitized showed the similar characteristics curve at four different constant temperatures.

The gaming industry is experiencing rapid growth due to recent advances in technology. Game engines such as Unity and Unreal are being actively utilized. These game engines offer a variety of plugins to naturally extend the functionality of the engine. Among them, innovations in 3D graphics technology have made game characters more expressive and enhanced the user experience. However, traditional 3D modeling approaches can sometimes bring limitations and challenges. In particular there are problems with the representation of fine details when utilizing general photos through AI scanning. This paper aims to overcome these difficulties by designing and implementing a game 3D character generation framework using Stable Diffusion. By improving the creation process by utilizing concept art images without hairstyles, it enables fast and efficient character creation. The application of this framework allows for faster and more consistent character creation with fewer steps in the creation process and helps game developers to adapt characters to the engine more easily and quickly. In addition, we verified the effectiveness and scalability of the 3D game character data generated by Stable Diffusion by checking the animation behavior in the game engine.

In nuclear power plant, there were many contaminated tanks dispose of radioactive fluid waste. These tanks are made of stainless-steel, and corrosion can occur when tanks are exposed to radioactive fluid waste containing moisture for a long time. Therefore, those sludge waste including radionuclide should be collected, solidified, and disposed of. If sludge can be melted, sludge can be easily solidified. However, melting points of sludge components (Fe2O3, NiO, Cr2O3) are very high as 1565, 1955, and 2435 , respectively. Therefore, melting sludge is difficult. If a solidification auxiliary material such as cement or asphalt is used to help solidify, solidification can easily occur, but cement and asphalt are vulnerable to heat. Vitrification using glass material can be solidification method, but the waste loading ratio of glass material is higher than 50%. High waste loading ratio is weakness in terms of volume reduction of waste. In this study, ferro frit powder (Na2O, K2O, CaO, Al2O3, B2O3, SiO2, ZnO) is used as solidification auxiliary material. When ferro frit powder mixed with sludge material are melted in sludge material, melted ferro frit powder can stick sludge material and can solidify sludge material without melting. Sludge can be solidified by using ferro frit powder with a smaller waste loading ratio than the vitrification method. However, since the waste loading ratio of the solidification auxiliary material is small, if ferro frit powder is not uniformly distributed between sludge powder, solidification may not be performed properly. Although the mixing ratio between sludge and ferro frit in solidified sludge is same, when the distribution of ferro frit powder in sludge is non-homogeneous, the difference in chemical and physical characteristics as compressive strength and leaching resistance can be observed in solidified sludge. As the ferro frit mixing ratio in the site where ferro frit exists was relatively high, the melting point of the mixed powder (sludge+ferro frit) decreased, and the mixed powder could not maintain its shape and melted. In the case of the area where ferro frit does not exist, since only the stainless-steel oxide sludge exists, sludge was not melted, and the shape was maintained. However, it was confirmed that the leaching resistance was lowered by visually observing the color change of the leachate within a short period of time (about 2 hours) when solidified sludge was immersed in the leachate.

The effect of oxidation time on the characteristics and mechanical properties of spent nuclear fuel cladding was investigated using Raman spectroscopy, tube rupture test, and tensile test. As oxidation time increased, the Raman peak associated with the tetragonal zirconium oxide phase diminished and merged with the Raman peak associated with the monoclinic zirconium oxide phase near 333 cm−1. Additionally, the other tetragonal zirconium oxide phase peak at 380 cm−1 decreased after 100 d of oxidation, whereas the zirconium monoclinic oxide peak became the dominant peak. The oxidation time had no effect on the tube rupture pressure of the oxidized zirconium alloy tube. However, the yield and tensile stresses of the oxidized nuclear fuel cladding tube decreased after 100 d of oxidation. The results of the scanning electron microscopy and transmission electron microscopy were represented with the in-situ Raman analysis result for the oxide characteristics generated on the cladding of spent nuclear fuel.

The mixing powder of vitrification material and metallic oxide sludge was solidified by hot isostatic press method and was tested to check whether the solidified waste disposal acceptance criteria were met or not. From various contaminated tank in nuclear power plants, and other nuclear energy facilities, radioactive sludge based on metallic oxide can be generated. The most of tank consist of stainless steel can be oxidated by the long-term exposure on oxygen and moisture, and then can be made sludge layer based on metallic oxide on the inner wall of contaminated tank. Radioactive sludge waste should be solidified and disposed. Melting and hardening is the most basic method for solidification. The melting points of metallic oxide of stainless steel as Fe3O4, NiO, Cr2O3 are 1597, 1955, 2435, respectively. Those are very high temperature. To melt these metallic oxides, a furnace capable of raising the temperature to a very high temperature is required, which requires a lot of thermal energy, which may lead to an increase in disposal cost. Therefore, it is necessary to lower the melting point and solidify non-melted metallic oxide powder by adding vitrifying material powder as Na2O, SiO2, B2O3. The more vitrification material is added, the easier it is to solidify the sludge based on metallic powder at a low temperature, but there is a problem in that the total waste volume increases due to the addition of vitrification material. In this study, the mixing ratio and temperature conditions that can fix the sludge while adding a minimum amount of vitrification material will be confirmed. Mixing ratio conditions of the vitrification material and sludge powder are 10:90, 15:85, 20:80, 25:75. To fix the metallic oxide sludge by melting only the vitrification material without completely melting the metallic oxide, compression by external pressure is required. Therefore, the HIP (Hot Isostatic Pressing) method was used to solidify the metallic oxide sludge by simultaneously heating and pressurizing it. Because the softening points of most of vitrification based on Na2O, SiO2, B2O3 are ranged from 800 to 1000, temperature conditions are 800, 900, 1000. Since the compressive strength for disposing of the solidified materials was 3.4 MPa, the maximum pressure condition was set to 5000 psi (about 34 MPa), which is 10 times 3.4 MPa. And optimal mixing ratio, temperature, pressure conditions that meet the solidified waste disposal acceptance criteria will be found.

The International Organization for Standardization (ISO) published ISO 9001 Quality Management System (QMS)-Requirements in 1987 and has revised four times since then. ISO 9001:2015 is the latest edition. This latest edition has two most noticeable changes. The first major change of new edition focuses on performance with an emphasis on Risk-Based Thinking (RBT) to enhance the process approach. The new edition consists of ten clauses whose first three clauses are largely same as older edition but risks are clearly stated and stressed in last seven clauses, emphasizing on Plan-Do-Check-Act cycle at all levels in the organization. The second major change is that the new edition has the same overall structure as other ISO management system standards known as High Level Structure (HLS) with Annex SL. The companies obtained the certificate of new ISO 9001:2015 QMS by September 15, 2018 in order to maintain as an ISO QMS registered firm. In this article we collected transition audit data from more than 100 companies that registered ISO 9001:2015 QMS for recent three years. We performed a statistical analysis to disclose the relationships between the characteristics of companies and the minor nonconformities found in ISO 9001:2015 requirements during transition audit processes. We also aim to interpret the findings and deduce the implications of the statistical results.

Supplementation with glutamine(Gln) has beneficial effects on intestinal and immune functions. Cage-reared chicks suffer from various stressors during early growth, but the effect of Gln supplementation on growth performance and stress hormones is uncertain. We investigated the effect of Gln on growth performance and blood corticosterone levels in Hyline chicks. Groups of 3-day-old chicks were fed one of three diets: normal feed(CTL group), normal feed supplemented with a low level of Gln, or normal feed supplemented with a high level of Gln. Growth and various physiological and biochemical parameters related to stress were assessed. On day 30, after a 24-h fast, blood was analyzed for corticosterone and other parameters, including glutamic oxaloacetic transaminase, gamma-glutamyl transpeptidase, total bilirubin, lactate dehydrogenase, total cholesterol, high-density lipoprotein cholesterol, blood urea nitrogen, blood total protein, and inorganic phosphate. Growth performance was maintained in Gln supplemented groups. The corticosterone level was decreased in the two groups receiving Gln supplementation compared to the CTL, and all other humoral factors did not differ between the groups. We suggest that Gln supplementation is a safe and useful strategy for reducing the effects of stress in cage-reared chicks.