The design of buried underground flexible pipes proposed in domestic standards does not properly reflect changes in ground characteristics. Overseas standards suggest that pipe deflection must be considered while designing them. Therefore, in this study, the structural behavior of underground polyvinyl chloride pipes was investigated through experiments and the finite element analysis. In addition, when the pipe deflection occurred at 3% and 5%, the hydraulic characteristics of the polyvinyl chloride pipe showed a slight difference compared to the round pipe.

Fiber-reinforced polymer (FRP) exhibits superior tensile strength and corrosion resistance compared to steel but has a lower elasticity. Recently, researchers have addressed this by proposing composite sections of FRP and concrete. To ensure the intended composite behavior, these FRP–concrete sections should exhibit sufficient stress transfer between the two elements through a shear connection. Herein, various shear connection methods were proposed to improve the composite behavior of glass fiber–reinforced polymer (GFRP) plates and concrete. Through push-out tests, the behavior characteristics of the prepared specimens were analyzed. The findings confirm that an FRP shear key (FSK) with a small cross-section resists high shear stresses, making it suitable for sections vulnerable to damage from bolt drilling. Additionally, combining an FSK with bolts as shear connectors on a GFRP plate proves beneficial in preventing the fracture of the plate and improving the shear resistance.

The demand for high-strength steel is rising due to its economic efficiency. Low-cycle fatigue (LCF) tests have been conducted to investigate the nonlinear behaviors of high-strength steel. Accurate material models must be used to obtain reliable results on seismic performance evaluation using numerical analyses. This study uses the combined hardening model to simulate the LCF behavior of high-strength steel. However, it is challenging and complex to determine material model parameters for specific high-strength steel because a highly nonlinear equation is used in the model, and several parameters need to be resolved. This study used the particle swarm algorithm (PSO) to determine the model parameters based on the LCF test data of HSA 650 steel. It is shown that the model with parameter values selected from the PSO accurately simulates the measured LCF curves.

이 연구는 핵무기 폭발 시 발생하는 효과 변인을 토대로 북한이 언제, 어떤 방법으로 핵무기를 운용할 것이며, 핵폭발 시 생성되는 방사성 물 질이 자연환경과 인공물의 영향에 따라 도심지에서 어떤 거동 현상을 보 이는가와 이를 고려한 국민 방호의 대비 방향에 관한 것이다. 연구 결과 핵무기는 폭발 고도에 따라 그 효과가 달라지며, 북한은 이를 활용하여 개전 초부터 가장 효과적인 공격을 할 것으로 예측되었다. 즉, 북한은 개 전 초 한미연합군과 정부의 지휘‧통제‧통신체계를 무력화하기 위해 저위 력핵무기로 지하 폭발을, 전쟁 도중 결정적인 목표 확보를 위해 전술핵 무기로 저공 폭발을, 전쟁 말기 패색이 짙어지는 위기 시에는 전술핵무 기로 지표면 폭발을 시도할 것이다. 북한의 핵무기 공격 후 발생되는 방 사성 물질은 낙진의 형태로 일정 지역을 오염시킬 것이며, 방사성 물질 이 도심지로 유입된다면 공기역학 또는 유체역학적 거동을 보임으로써 다양한 형태의 오염과 위험이 존재할 것으로 분석되었다. 이에 따라 국 민 방호를 위해서는 북한의 핵무기 공격 양상을 고려 최악의 상황을 가 정한 대비가 평시에 완료되어야 하며, 전쟁 개시 이후에는 당시의 공격 유형에 부합한 대응 및 복구가 뒤따라야 한다. 아울러 방사능 낙진의 거 동을 세밀히 분석하고 이를 고려하여 핵폭발 초기 효과에 대비하는 주민 대피와 이를 후속하는 낙진에 대응하기 위한 주민 소개는 분리되어야 한다.

With the increasing attention to environmental pollution caused by particulate matter globally, the automotive industry has also become increasingly interested in particulate matter, especially particulate matter generated by automobile brake systems. Here, we designed a coating composition and analyzed its mechanical properties to reduce particulate matter generated by brake systems during braking of vehicles. We designed a composition to check the mechanical properties change by adding Cr3C2 and YSZ to the WC-Ni-Cr composite composition. Based on the designed composition, coating samples were manufactured, and the coating properties were analyzed by Vickers hardness and ball-on-disk tests. As a result of the experiments, we found that the hardness and friction coefficient of the coating increased as the amount of Cr3C2 added decreased. Furthermore, we found that the hardness of the coating layer decreased when YSZ was added at 20vol%, but the friction coefficient was higher than the composition with Cr3C2 addition.

YSZ (Y2O3-stabilized zirconia)-based ceramics have excellent mechanical properties, such as high strength and wear resistance. In the application, YSZ is utilized in the bead mill, a fine-grinding process. YSZ-based parts, such as the rotor and pin, can be easily damaged by continuous application with high rpm in the bead mill process. In that case, adding WC particles improves the tribological and mechanical properties. YSZ-30 vol.% WC composite ceramics are manufactured via hot pressing under different pressures (10/30/60 MPa). The hot-pressed composite ceramics measure the physical properties, such as porosity and bulk density values. In addition, the phase formation of these composite ceramics is analyzed and discussed with those of physical properties. For the increased applied pressure of hot pressing, the tetragonality of YSZ and the crystallinity of WC are enhanced. The mechanical properties indicate an improved tendency with the increase in the applied pressure of hot pressing.

PURPOSES : This study aims to understand the effect of defective dowel bar installation on jointed concrete pavement (JCP), which can cause joint freezing, spalling, cracking, and faulting and finally shorten the lifespan of the pavement. METHODS : A comprehensive field survey was undertaken at an expressway construction site in South Korea to assess dowel bar installation conditions. In addition, finite element (FE) analysis was used to simulate JCP behavior with both vertical and horizontal dowel misalignments. Different temperature conditions, including a change of -55 °C and gradient of -0.1 °C/mm, were integrated into the FE model to examine horizontal slab contraction and simultaneous slab curling. RESULTS : The analysis revealed pronounced slab behaviors under specific temperature changes, particularly when combined with dowel misalignments. The simultaneous effects of horizontal contraction and slab curling owing to temperature changes and gradients became more evident in the presence of dowel misalignments. CONCLUSIONS : The results confirmed that dowel bar misalignment considerably affected the behavior of the JCP, thereby emphasizing the importance of the proper installation of dowel bars.

PURPOSES : In this study, the initial behaviors of shoulder concrete slabs and tiebars at the longitudinal construction joints between the shoulder JCP and mainline CRCP are investigated. METHODS : The strains of concrete and tiebars were measured at the longitudinal construction joint between the CRCP and JCP. Measurements were performed using data accumulated over a month after concrete placement. The contact conditions were investigated by comparing the strains at each location. RESULTS : The longitudinal construction joints between the shoulder JCP and mainline CRCP exhibited the composite behavior of bonding and friction, and a virtual neutral axis was formed inside the JCP. At the connection of the shoulder concrete, the strain and temperature of the concrete were inversely proportional. The tiebars connecting the CRCP and JCP exhibited different behaviors depending on the bonding conditions around the tiebars of the construction joints. In the presumed state in which the bonding condition was maintained, the concrete temperature and tiebar strain were directly proportional; however, the presumed state of the separation condition exhibited an inversely proportional relationship. In the 24-h behaviors of the tiebars, the effects of the horizontal and curling movements overlapped, and the strains of the measured tiebars increased at the minimum and maximum temperatures of the shoulder JCP. CONCLUSIONS : The strains in the tiebars and concrete slabs primarily depended on the boundary conditions (bonding and friction) of the longitudinal construction joint between the shoulder JCP and mainline CRCP.

철근콘크리트는 가장 널리 사용되는 건축자재로 최근 노후 시설물이 증가하면서 노후 구조물에 대한 안전성 검토가 매우 중요한 문제로 대두되고 있다. 본 연구에서는 대표적인 열화 인자인 동결융해와 철근부식 그리고 동결융해와 철근부식의 복합적 열화에 따른 RC 휨 부재의 거동을 실험적으로 평가하였다. 4개의 철근콘크리트 휨 부재를 제작하였으며 각 열화 인자에 따른 RC 휨 부재의 거동을 평가하기 위해 4점 재하법을 이용하여 정적실험을 수행하였다. 동결융해는 총 300 사이클의 급속동 결융해실험을 수행하였으며, 부식은 전위차부식촉진실험을 수행하였다. 실험 결과, 동결융해로 인해 콘크리트의 압축강도가 12% 감소하였으며 RC 보 부재의 상부 압축부의 파쇄 범위가 증가하였고 최대강도가 6% 감소하였다. 철근부식으로 인해 RC 휨 부 재의 항복강도가 1.2%, 최대강도가 7% 감소하였으며, 복합열화로 인해 RC 휨 부재의 항복강도가 2.4%, 최대강도가 9% 감소하 였다.

본 연구에서는 GFRP(Glass Fiber Reinforced Polymer)를 주 보강근으로 사용하였으며, 정착길이가 없는 시험체를 제작 하여 4점 재하 휨시험을 수행하였다. 각 변수는 공칭지름이며 공칭지름 D13, D16, D19, 총 3가지의 변수로 이루어져있다. 휨 모 멘트는 공칭지름이 커질수록 약24.17%, 45.92% 강도가 증가하였으나 공칭 휨 강도를 고려하였을 때, 인장 강도와는 달리 공칭 지름에 비례하여 유사한 성능을 나타냄을 알 수 있었다. LVDT로 보강근과 콘크리트와의 부착성능을 확인하였고, 그 값은 매우 미미하며 거의 발생 되지 않은 것으로 판단된다. 또한 DIC로 시험체의 처짐을 확인하였으며, 실세 처짐 값과 유사함을 알 수 있었다.

Recently, Free-Form and Irregular Shape high-rise buildings are constructed by IT technology development. Tilted shaped high-rise building which is one of Irregular shape high-rise buildings can cause lateral displacement by gravity load and lateral load due to tilted elevation shape. Therefore, it is necessary to review the behavior and structural aspects of the Tilted shape high-rise building by gravity load. In this paper, the dynamic characteristics of a tilted structure with a dual-core were analyzed with the core location as a design variable, and response behavior, vulnerable members, and vulnerable layers to earthquake loads were analyzed. As a result of the analysis, as the location of the core moved in an tilted direction, the eccentric distance and eccentric load decreased, reducing the axial force of the vertical members. However, the location of the core had little effect on the response.