철근은 콘크리트와 결합하여 인장 능력을 보완하고 표면 피막으로 부식을 방지하지만, 탄산화 및 염화물 침투로 인해 부식이 발생하면 내력이 저하된다. 이를 해결하기 위해 내부식성이 뛰어난 GFRP(Glass Fiber Reinforced Polymer) 보강근이 철근 대채제로 주 목받고 있다. 본 연구는 직경에 따른 GFRP 보강근의 부착특성을 철근과 실험적으로 비교 분석하였다. 콘크리트는 약 39MPa의 고강도 에 가까운 콘크리트를 사용하였으며, 보강근의 직경은 D10과 D13을 사용하였다. 실험 결과, GFRP 보강근의 평균 부착 응력은 17.21MPa로 철근의 18.14MPa와 유사하게 나타났다. GFRP 보강근의 슬립 양은 3.05mm로 철근의 1.53mm 보다 크게 나타났다. 또한 GFRP의 경우 인발 과정에서 표면에 국부손상이 발생하는 것을 확인하였다.

본 연구에서는 GFRP(Glass Fiber Reinforced Polymer)를 주 보강근으로 사용하였으며, 정착길이가 없는 시험체를 제작 하여 4점 재하 휨시험을 수행하였다. 각 변수는 공칭지름이며 공칭지름 D13, D16, D19, 총 3가지의 변수로 이루어져있다. 휨 모 멘트는 공칭지름이 커질수록 약24.17%, 45.92% 강도가 증가하였으나 공칭 휨 강도를 고려하였을 때, 인장 강도와는 달리 공칭 지름에 비례하여 유사한 성능을 나타냄을 알 수 있었다. LVDT로 보강근과 콘크리트와의 부착성능을 확인하였고, 그 값은 매우 미미하며 거의 발생 되지 않은 것으로 판단된다. 또한 DIC로 시험체의 처짐을 확인하였으며, 실세 처짐 값과 유사함을 알 수 있었다.

This paper presents a method to measure the similarity of assigned jobs in the gravure printing operation based on the chromaticity and color sequence, and order the jobs accordingly. The proposed dispatching rule can be used to fulfill diverse manufacturing site requirements because the parameters can be adjusted to prioritize chromaticity and color sequence. In general, dispatching rules either ignore the job-changing time or require that the time be clearly defined. However, in the gravure printing operation targeted in this study, it is difficult to apply the general dispatching rule because of the difficulties in quantifying the job-changing time. Therefore, we propose a method for generalizing assignment rules of the job planner, allocating relative similarity among assigned jobs, and determining the sequence of jobs accordingly. Chromaticity priority is determined by the arrangement of the color assignments in the printing operation; color sequence priority is determined by the addition, deletion, or change in a specific color sequence. Finally, the job similarity is determined by the dot product of the chromaticity and color sequence priorities. Implementation of the proposed dispatching rule at an actual manufacturing site showed the planner present the same job order as that obtained using the proposed rule. Therefore, this rule is expected to be useful in industrial sites where clear quantification of the job-changing time is not possible.

This paper proposes a dynamic magnetic field emulator (DMFE), which can electrically emulate information for the magnetic stripes of most widely used credit cards. Payment transactions with most common credit cards are performed by reading the card’s information, encoded in magnetic stripes, using the reader head of a point-of-sale (POS) system. A stripe-type permanent magnet is attached to the back side of the credit card, and information for payments or value-added service is reorganized by exposing it to strong magnetic field. The process of data recording and retrieving as stated above has been pointed out as a major cause of illegal credit card use, because the information on the magnetic stripe is always exposed, and is thus vulnerable to forgery or alteration. A dynamic magnetic field emulator displays card information only when necessary by using the principle of solenoidal magnets. The DMFE proposed in this paper can prevent fraudulent use if it is operated with a device, like a smart phone, or a separate user-authentication procedure. In addition, because it is possible to display various information as needed, it can be utilized for a smart multi-card application, in which information for multiple cards is stored in one card, and can be selected and used as needed. This paper introduces the necessity of the DMFE and its manufacturing principles. As a result, this study will be helpful for making various application cases in payment, which is a core area of the Fintech (a newly-coined word of finance and technology) industry.

본 연구에서는 신용카드 결제에서 가장 보편적으로 사용되는 자기띠 방식 카드의 기능을 전자적으로 모사하는 동적자장모사장치의 개발을 제안한다. 동적자장모사장치를 신용카드에 활용하여 결제가 필요한 경우에만 활성화하면, 정적으로 노출되어 있는 자기띠를 사용하는 기존 카드가 개인정보의 위/변조에 취약한 단점을 극복할 수 있게 된다. 또한 일회용비밀번호(OTP) 기능과 결합하면, 결제마다 가상의 카드번호를 사용하게 되어 위/변조를 원천적으로 예방할 수도 있다. 기술의 발전으로 다양한 결제방식이 제안되고 있으나, 실제 시장 보급은 매우 느리다. 이와 같은 이유는 여러 가지가 있지만, 결제 기반체계의 교체에 천문학적인 비용이 소요되는 문제가 가장 큰 요인으로 꼽히고 있다. 동적자장모사장치가 신용카드 두께 규격을 충족하면, 기존 결 제 기반체계를 그대로 활용할 수 있어, 한 장의 카드에 여러 카드를 담는 등의 스마트 멀티카드 기술 등의 다양한 핀테크 기술의 활용이 용이해진다는 장점이 있다.

As film products are increasingly used in a wide range of areas, from producing traditional flexible packaging to high-tech electronic products, a higher level of quality is demanded. Most film products are made in the form of rolled finished goods, therefore, various quality issues related to their shape characteristics must be addressed. The thickness of the film products is one of the most common and important critical-to-quality attributes (CTQs). Particularly, the degree of thickness uniformity is more important than other thickness parameters, because it will be potential causes of many secondary thickness-related quality problems, such as wrinkles or faulty windings. To control the degree of thickness uniformity, the fixed bending region is oneof the most important CTQs to manage. Fixed bending regions are special points in the transverse direction of a rolled product with consistent minute variations of the thickness gap. This paper describes the measurement and analysis of thickness uniformity data, which were performed in a real manufacturing field of biaxial oriented polypropylene (BOPP) film. In previous researches, quality function deployment (QFD) or fault tree analysis were used to find the most critical process attributes out to controlthe CTQ of thickness uniformity. Whereas, this paper uses traditional control charts to find the most critical process attributes out in this problem. In addition, the selection of one of the major critical process attributes (CTPs) that is expected to affect the CTQ of thickness uniformity is also described. The selected critical-to-process attributes are the controlled temperatures along the transverse direction. A dramatic improvement in thickness uniformity was observed when the selected CTPs were controlled.

This study examined a feasibility of coagulation as post-treatment to remove sulfide and phosphorus for the effluent of anaerobic fluidized bed reactor (AFBR) treating domestic wastewater. Removal efficiencies of sulfide, phosphorus and COD by coagulation were not affected by pH in the range of 5.9 to 7.2. Alkalinity requirement could be estimated by the amount of Fe3+ to form Fe(OH)3(S) and to remove sulfide and phosphorus. At coagulant aid dosage of 2 mg/L, anionic polymer showed best results regarding size and settleability of flocs. Sulfide removal for the AFBR effluent at the Fe3+/S2- ratio of 0.64, close to the theoretical value of 0.67 found with a synthetic wastewater, was only 75.2%. One of the reasons for this low sulfide removal is that the AFBR effluent contains, phosphorus, hydroxide and bicarbonate which can react with Fe3+ competitively. Concentrations of sulfide and phosphorous reduced to below 0.1 and 0.5 mg/L, respectively, at the Fe3+/S2- ratio of 2.0. Average effluent COD of 80 mg/L, mostly soluble COD, was obtained at the dosage 50 mg Fe3+/L (Fe3+/S2- ratio of 2.0) with corresponding COD removal of 55%. For better removal of COD, soluble COD removal at the AFBR should be enhanced. Coagulation with Fe3+ removed sulfide, phosphorus and COD simultaneously in the AFBR effluent, and thus could be an alternative process for the conventional wastewater treatment processes where relatively high quality effluent is not required.

As film products are more frequently used from producing traditional flexible packing products to high-tech electronic products, requested higher level of quality. Most film products are made in the shape of roll-type finished goods, so various quality problems are addressed related with their characteristics of shape. Thickness of film products is one of the most common and important quality problems. Particularly the Degree of thick smoothness is more important than other thickness issues, because it causes many secondary issues of thickness-related quality problems like wrinkles or faulty windings. Thick smoothness must be controlled in both horizontal and vertical direction. In this paper, HOQ (house of quality) was built to interpret VOC (voice of customers) to CTQs (critical to quality). To decide priorities of VOC and CTQs, both techniques are applied. One is AHP (analytic hierarchy process) with pairwise comparison. The other is an absolute weight calculation method with level-up rate. From the result of HOQ, it is certain that the thick smoothness is the most important CTQ in film manufacturing industry. Finally, this paper presents how to monitor and improve repetitive coincidence of microscopic deviation of thickness in some special vertical points.

음식물 폐기물 침출수를 처리하는 분리막 결합 고온 혐기성소화공정(생물학적 반응조) (Anaeorobic Membrane Bioreactor, AnMBR)의 파일럿 운전에서 분리막의 교차여과 속도와 막간압력이 파울링에 미치는 영향을 관찰하였다. 연구 결과 정압여과 하에서 교차여과 속도가 증가할수록 파울링의 속도는 현격히 감소되었다. 그러나 이와 같은 영향은 낮은 막간압력에서 더욱 효과적이었다. 막간압력이 증가할수록 여과대상 물질의 압축성으로 인해 투과성이 상대적으로 낮은 파울링층(혹은 케익층)이 분리막 표면에 형성된 것에 기인된 듯하다. 여과대상 시료의 입도분석을 해 본 결과 입자크기는 약 10~100mum 범위에서 분포하였고 이에 따라 브라운확산에 의한 역수송보다 분리막 표면에서 교차여과에 의해 발생하는 전단력이 입자의 역수송에 더욱 기여하고 있음을 예측할 수 있었으며 이는 AnMBR의 연속운전을 통해 재확인할 수 있었다. 운전 후 막 부검을 실시한 결과 유기 및 무기 파울링이 모두 관찰되었으나 어느 것이 지배적인 파울링 기작을 나타내는지는 앞으로 더욱 연구가 필요하다. 무기 파울링의 경우 대부분 분리막 표면에서 스케일링 형성이 지배적이었으며, 따라서 분리막의 공극 막힘에 주로 기여하는 작은 콜로이드성 유기물질의 경우 분리막 표면에서 전단력에 의한 역수송 효과는 그다지 크지 않을 것으로 사료된다.

The objective of this research is to introduce key performance indicators (KPIs) measuring overall equipment effectiveness (OEE) or overall operation effectiveness (OOE) effectively. OEE is one of the most effective KPI to measure the productivity and quality levels of an equipment-centric manufacturing company and widely implemented with a spreaded TPM (total productive maintenance). OEE is the most representative time-related KPI. For ease of measurement, OEE is calculated on the basis of the quantity of the processing materials and theoretical cycle time instead of using time-related sub-indicators. Hence, setting up theoretical cycle times is the most important aspect of the OEE measurement. Increasing customer's demand and developed manufacturing technology, more products can be made in a machine. So there will be multiple theoretical cycle times in a machine, but they have not been extensively considered for setting up theoretical cycle times in previous research. Futhermore the limitation to measure a performance of an operation which is consists of multiple machines is often mentioned in previous research. This paper shows how to measure OOE based on multiple theoretical cycle time.

As the population of the silver generation is increasing, the importance and effects of the market for the silver generation are also growing. We segments the categories of the silver generation into six sub-segments using based on the factors like life s

Anaerobic reductive dehalogenation of perchloroethene (PCE) was studied with lactate as the electron donor in a continuously stirred tank reactor (CSTR) inoculated with a mixed culture previously shown to dehalogenate vinyl chloride (VC). cis-1,2- dichloroethene (cDCE) was the dominant intermediate at relatively long cell retention times (〉56 days) and the electron acceptor to electron donor molar ratio (PCE:lactate) of 1:2. cDCE was transformed to VC completely at the PCE to lactate molar ratio of 1:4, and the final products of PCE dehalogenation were VC (80%) and ethene (20%). VC dehalogenation was inhibited by cDCE dehalogenation. Propionate produced from the fermentation of lactate might be used as electron donor for the dehalogenation. Batch experiments were performed to evaluate the effects of increased hydrogen, VC, and trichloroethene (TCE) on VC dehalogenation which is the rate-limiting step in PCE dehalogenation The addition of TCE increased the VC dehalogenaiton rate more than an increase in the H2 concentration, which suggests that the introduction of TCE induces the production of an enzyme that can comtabolize VC.

현재 국내에서 발생하는 음폐수의 해양투기 금지와 음식물류 폐기물의 에너지화 정책에 따라 유기성 폐기물의 혐기소화를 통한 바이오가스화 시설이 지속적으로 설치 및 운영되고 있다. 그동안 많은 연구와 운영 경험을 통해 유기성 폐기물의 바이오가스화 공정은 점차적으로 안정화되어 가고 있는 가운데, 해당 시설에서 발생하는 혐기소화여액에 대한 적정 처리가 전체 시설의 경제성에 큰 영향을 미치고 있다. 해외, 특히 유럽에서는 유기성 폐기물의 혐기소화여액을 대부분 퇴비 또는 비료로 활용하고 있으나 국내에서는 경작 면적 및 시비 시기 등에 대한 제약으로 인해 해외의 경우처럼 혐기소화여액을 퇴비 및 비료로 활용하는데 한계를 가지고 있다. 이에 대다수의 국내 음식물류 폐기물 바이오가스화 시설에서는 혐기소화여액을 별도의 폐수처리 후 하수처리장에 연계 처리하고 있으며, 고형물인 탈수케익은 일부 퇴비원료로 생산하고 있으나 이에 대한 수요 및 구매 매력도가 떨어져 무상공급 또는 유상처리하고 있는 실정이다. 이에 따라 탈수케익을 퇴비원료로 생산하는 대신 매립 또는 소각 처리로 전환하는 시설도 늘어나고 있다. 또한, 음식물류 폐기물의 혐기소화여액은 높은 질소 농도로 인해 하수처리장 연계수질에 따라 단순 응집침전부터 다단 고도처리까지 적용하여 처리하고 있어, 본 과제에서는 국내 음식물류 폐기물 바이오가스화 시설을 직접 방문 조사하여 각 시설의 폐수처리공정 성능 및 애로사항 파악을 통해 주요 연계수질 기준에 따른 최적 폐수처리공정 선정 Guideline을 도출하고자 하였다.