In the event of an emergency such as facility shutdown during process operation, the by-product gas must be urgently discharged to the vent stack to prevent leakage, fire, and explosion. At this time, the explosion drop value of the released by-product gas is calculated using ISO 10156 formula, which is 27.7 vol%. Therefore, it does not correspond to flammable gas because it is less than 13% of the explosion drop value, which is the standard for flammable gas defined by the Occupational Safety and Health Act, and since the explosion drop value is high, it can be seen that the risk of fire explosion is low even if it is discharged urgently with the vent stock. As a result of calculating the range of explosion hazard sites for hydrogen gas discharged to the Bent Stack according to KS C IEC 60079-10-1, 23 meters were calculated. Since hydrogen is lighter than air, electromechanical devices should not be installed within 23 meters of the upper portion of the Bent Stack, and if it is not possible, an explosion-proof electromechanical device suitable for type 1 of dangerous place should be installed. In addition, the height of the stack should be at least 5 meters so that the diffusion of by-product gas is facilitated in case of emergency discharge, and it should be installed so that there are no obstacles around it.

최근의 국제사회는 경제성장에 따른 기상이변의 방지를 위한 국가 간 기후변화협력 체결(1992년)을 시작으로 환경 오염물질 배출 저감을 요구하고 있다(Moon et al, 2014). 따라서 최근에는 전 세계적으로 지구온난화와 기후변화의 원인이 되는 온실가스의 발생을 줄 이고자 노력하고 있으며, 건설 산업은 이러한 온실가스 배출량의 주요 원인으로 인식되고 있다(Kong et al., 2016) 교량 건설사업이 환 경에 미치는 정도를 전과정평가(Life Cycle Assessment, LCA)방법을 활용하여 재료 및 공법의 지속가능성에 대한 객관적, 정량적 평가 체계를 구축하고자한다. 본 연구에서는 선행적으로 국내외 환경성적표지제도(Environment Product Declaration, EPD), 탄소발자국(Carbon footprint) 등을 분석함으로써, LCA 관련 제도에 대한 전반적인 동향을 파악하였다. 그다음, 국제적으로 통용되고 있는 제품 범주 규칙 (PCR)과 환경제품선언(EPD) 사례를 분석하여 LCA 관련 분석 범위를 확인했으며, 전과정영향평가(LCIA) 방법론과 국내외 LCI DB(Ecoinvent, Athena Pavement LCA, LCA PAVE 등)을 분석함으로써 국내외 환경 영향인자 관련 기술자료를 확보하였다. 또한, 건설 자재, 시공, 유지 관리 관련 설계 명세서, 표준품셈, 단가 산출표를 분석함으로써, 자재 투입량, 장비 연료 소모량에 대한 기초 DB를 도출하였다. 기존 프로그램을 토대로 고속도로 온실가스 산정 프로그램을 개발하여 건설자재, 수송, 시공, 유지 관리 단계에서의 탄소 배출량 산정 사례 분석을 수행했다. 교량 분야는 STEEL BOX교를 선정했다. 이에대하여 건설자재. 시공, 수송, 유지관리에 탄소배출량 을 산정하였다. 산정된 결과를 바탕으로 LCA분석의 기틀을 마련하였으며, 이를 통하여 추후 추가적인 기초 DB를 추가하여 교량 분야 전과정평가 LCA를 분석하기 위한 플랫폼을 제작할 예정이다.

산업화에 따른 이산화탄소 등 온실가스 발생량의 증가는 지구 온난화 현상을 가속화 하였다. 이러한 현상은 지난 수 세기동안 지속 되어왔으며 최근 우리 인간 삶에 지대한 영향을 미치고 있다. 이러한 위험에 따라 주요 선진국들은 에너지 감축 및 온실가스 배출량 제한에 대하여 매우 적극적인 입장을 취하고 있다. 유럽연합(EU)은 온실가스 배출 절감을 위해 시행 중인 ‘탄소배출권 거래제(Emission Traiding System)’ 개혁안에 대하여 합의하여 2050년까지 인위적 생성되는 탄소 배출량을 자연적으로 흡수되는 양과 동일하게 하는 ‘탄 소중립’을 목표로 제시하였다. 국내에선 환경영향평가의 대상이 되는 계획 및 개발사업에 도로건설이 포함되는 ‘탄소중립기본법 시행 령’이 지난 3월 의결되어 시행되었다. 이렇듯, 국내외에선 이러한 탄소저감 제도 구축에 노력을 기울이고 있다. 국내에선 도로건설이 환경영향평가의 대상으로 설정되었으나 2011년 국토교통부에서 배포한 시설물별 탄소배출량 산정 가이드라인 외의 구체적인 생애주기 분석 방법이 부재한 상황이다. 따라서 본 연구에서 국제 표준 ISO 14040의 전과정평가 LCA(Life Cycle Assessment) 방법과 2011년 국 토교통부의 시설물별 탄소배출량 산정 가이드라인을 따라 국내 LCI DB(Life Cycle Inventory Data Base)를 활용한 도로 분야의 전과정 탄소 배출량을 산정하였다. 이후 장비 연료 소모량과 자재 사용에 대한 국내외 LCI DB를 추가하여 도로 건설 전 과정에 대한 LCA 분석 플랫폼을 제작할 예정이다.

PURPOSES : Carbon dioxide (CO2) is a cheaper and easier to installer fire suppressant than other extinguishing gases and is easy to install, but extinguishes fires by is suffocation. As a result, suffocation accidents continue to occur in facilities equipped with CO2 fire-extinguishing facilities, Emission standards have yet to be established. This study aims to address the issue. METHODS : To effectively remove CO2 emitted from installed systems, we reviewed and analyzed previous related research and existing international standards. RESULTS : In protected areas where CO2 fire-extinguishing systems are installed, emission facilities should discharge the emitted CO2 before it enters the protected spaces. CO2 sensors can determine whether safe entry is possible or whether respirators are required. CONCLUSIONS : This study presented a specific installation method for emission facilities capable of actively discharging CO2. Applying this method is expected to contribute to improving safety in facilities equipped with CO2 fire-extinguishing facilities.

본 연구에서는 분리막 생물반응기(membrane bioreactor, MBR)에서 발생되는 생물막오염 완화에 탁월한 효과를 가진 분리막을 개발할 목적으로, 친수성 산소 기능기가 많은 탄소나노구체(carbon nanosphere, CNS)를 합성한 뒤, 이를 첨가 제로 활용하여 친수성과 다공성 기공 구조를 갖는 고성능 한외여과막을 제조하였다. CNS는 막 표면에 초승달 모양의 기공을 형성하였고, CNS 함량을 4.6 wt%까지 증가시킴에 따라 최대기공 크기보다 큰 결함을 야기하지 않으면서 평균 표면 기공 크 기를 약 40% 증가시키는 것으로 나타났다. 또한, CNS 복합막의 다공성 기공 구조는 CNS의 등방성 형태와 상대적으로 낮은 입자 수밀도 덕분에 CNS 첨가에 따른 고분자 용액의 점도 급등이 방지됐기 때문이라고 판단된다. 그러나 너무 다공성이 커 지게 되면 기계적 물성이 저하되므로, 기공구조와 기계적 성질을 포함한 종합적인 고려를 했을 때 CNS2.3이 가장 우수하다 고 관측되었다. CNS2.3은 CNS0에 비해 수투과도가 2배 이상 높을 뿐만 아니라, MBR 공정에서 분리막 세정이 요구될 때까 지의 운전 시간도 5배 이상 연장시킨 것으로 확인되었다.

This study examined the power consumption of angling boats during entry, departure, and fishing operations using a black box-type storage device. Through this analysis, it determined the energy consumption and carbon emissions of small fishing boats used for catching the largehead hairtail. The energy consumption and carbon emissions were calculated using formulas provided by the Korea Energy Agency, which incorporated updated emission coefficients from 2022. The findings revealed that the average power consumption of small fishing boats for the largehead hairtail was 546.3 kWh, with a total energy consumption of 0.1164 TOE and carbon emissions of 24.057 CO2. The average energy consumption was calculated at 0.0006 TOE per kilogram, and the carbon emissions were determined to be 0.135 CO2/kg.

본 연구에서는 수소 자원의 활용도가 높아짐에 따라 수소 저장 용기의 내진 성능을 평가하기 위해 수소 저장 시설을 방문하여 현장 조사를 수행하였다. 외관 조사 중, 수조 저장 용기의 지지부에서 부식이 진행됨을 확인하였고, 이에 대한 대책안 으로 내부식성 재료인 CFRP로 대체하여 성능을 평가, 검증하였다. 이를 위해 현장 조사 결과를 바탕으로 상용 유한요소해석 프 로그램인 ABAQUS를 사용하였으며, 해석 결과 CFRP로 제작된 수소 저장 용기의 지지부는 강재 대비 약 12배 이상 뛰어난 성 능을 보였다. Hashin Damage Criteria를 기반으로 CFRP 지지부의 안전성 검토를 수행한 결과 최대 손상 지수가 0.065로 확인되 었다. 기초부 콘크리트의 경우, 쪼갬 및 휨 인장 응력에 대한 안전성을 검토하였으며, 허용 강도 대비 7~36%의 안전도를 보였 다. 이를 근거로 CFRP를 수소 저장 용기의 지지부에 적용하는 것은 합리적이며, 뛰어난 경제성을 보인다. 다만, 이러한 결과는 수치 해석에 의하므로 실규모 지진동 모사 시험을 통해 해석 모델의 신뢰성을 보충할 필요가 있다.

This research investigated the preparation of activated carbon derived from Krabok (Irvingia malayana) seed shells to improve the quality of crude glycerol obtained during biodiesel production. The activated carbon was prepared using a dry chemical activation method with NaOH, utilizing an innovative biomass incinerator. The results revealed that the resulting KC/AC-two-step exhibited favorable physicochemical adsorption properties, with a high surface area of 758.72 m2/g and an iodine number of 611.10 mg/g. These values meet the criteria of the industrial product standard for activated carbon No. TIS 900-2004, as specified by the Ministry of Industry in Thailand. Additionally, the adsorption efficiency for methylene blue reached an impressive 99.35 %. This developed activated carbon was then used to improve the quality of crude glycerol obtained from biodiesel production. The experimental results showed that the KC/AC-two-step increased the purity of crude glycerol to 73.61 %. In comparison, commercially available activated carbon (C/AC) resulted in a higher crude glycerol purity of 81.19 %, as analyzed by the GC technique. Additionally, the metal content (Zn, Cu, Fe, Pb, Cd, and Na) in purified glycerol using KC/AC-two-step was below the standards for heavy metals permitted in food and cosmeceuticals by the Food and Drug Administration of Thailand and the European Committee for Food Contact Materials and Articles. As a result, it can be inferred that Krabok seed shells have favorable properties for producing activated carbon suitable as an adsorbent to enhance crude glycerol purity. Furthermore, the improved crude glycerol from this research has potential for various industrial applications.

The complexation of silicon with carbon materials is considered an effective method for using silicon as an anode material for lithium-ion batteries. In the present study, carbon frameworks with a 3D porous structure were fabricated using metal–organic frameworks (MOFs), which have been drawing significant attention as a promising material in a wide range of applications. Subsequently, the fabricated carbon frameworks were subjected to CVD to obtain silicon-carbon complexes. These siliconcarbon complexes with a 3D porous structure exhibited excellent rate capability because they provided sufficient paths for Li-ion diffusion while facilitating contact with the electrolyte. In addition, unoccupied space within the silicon complex, combined with the stable structure of the carbon framework, allowed the volume expansion of silicon and the resultant stress to be more effectively accommodated, thereby reducing electrode expansion. The major findings of the present study demonstrate the applicability of MOF-based carbon frameworks as a material for silicon complex anodes.

This work involves the development of a novel waste-derived carbon dots (CDs) conjugated with silver (Ag) nanohybrid system-based Fluorescence Resonance Energy Transfer (FRET) sensor for the detection of melamine. CDs and Ag nanoparticles served as energy donors and energy acceptors, respectively. CDs were synthesized from orange peel waste through a combined hydrothermal and ultra-sonication route. The synthesized CDs had hydroxyl, amino, and carboxyl groups on their surface, explaining that waste-derived CDs can act as reducing and stabilizing agents and showed strong absorption and fluorescence emission at 305 and 460 nm, respectively. The bandgap, linear refractive index, conduction band, and valance band potential of CDs were observed to be 2.86, 1.849, 1.14, and 4.002 eV, respectively. No significant difference was observed in the fluorescence properties at different pH (acid and alkaline) and ionic concentrations. Given their fluorescent nature, the synthesized CDs were used for the detection of melamine. The fluorescence of CDs was found to be quenched by Ag+ due to the FRET energy transfer between CDs to Ag. Notably, the zeta potential of Ag@CDs was changed from − 28.7 mV to − 30.6 mV after the incorporation of Ag+. Ag@CDs showed excellent selectivity and sensitivity toward the sensing of melamine in the aqueous solutions with the limit of detection ~ 0.85 μM. Increasing the melamine level also raises the FL intensity of Ag@CDs. The substrate was effectively used in the detection of melamine in milk as a real application and the recovery percentage was found to be 98.03%. Moreover, other adulterants such as urea and formaldehyde can be detected selectively by Ag@CDs. Overall, the synthesized Ag@CDs can be used as an efficient material for sensing applications involving such food adulterants.

Hierarchically porous carbon foam composites with highly dispersed Fe2O3 nanoparticles confined in the foam pores, facilely fabricated by hydrolysis-driven emulsion polymerization strategy. The as-generated acidic conditions of Fe3+ hydrolysis could catalyze the polymerization of phenolic resin, and the carbon-based composite materials containing iron oxides were obtained in situ. The structural characterization results show that HCF@Fe2O3 NPs-2 electrode has the largest specific surface area (549 m2/ g) and pore volume (0.46 cm3/ g). Electrochemical results indicates that typical HCF@Fe2O3 NPs-2 electrode displays good capacitive properties. including high specific capacitance (225 F/g at 0.2 A/g current density). Excellent magnification performance (capacity retention rate 80% as current density increases from 0.2 to 10 A/g). At the same time, HCF@SnO2 NPs was successfully synthesized by replacing hydrolyzed tin tetrachloride with ferric chloride. This study provides a new idea for the preparation of metal oxide–carbon matrix composites, and also highlights the potential of such carbon foams in application of energy storage.

Cellulose has experienced a renaissance as a precursor for carbon fibers (CFs). However, cellulose possesses intrinsic challenges as precursor substrate such as typically low carbon yield. This study examines the interplay of strategies to increase the carbonization yield of (ligno-) cellulosic fibers manufactured via a coagulation process. Using Design of Experiments, this article assesses the individual and combined effects of diammonium hydrogen phosphate (DAP), lignin, and CO2 activation on the carbonization yield and properties of cellulose-based carbon fibers. Synergistic effects are identified using the response surface methodology. This paper evidences that DAP and lignin could affect cellulose pyrolysis positively in terms of carbonization yield. Nevertheless, DAP and lignin do not have an additive effect on increasing the yield. In fact, combined DAP and lignin can affect negatively the carbonization yield within a certain composition range. Further, the thermogravimetric CO2 adsorption of the respective CFs was measured, showing relatively high values (ca. 2 mmol/g) at unsaturated pressure conditions. The CFs were microporous materials with potential applications in gas separation membranes and CO2 storage systems.

Carbon nanofibers (CNFs) are promising materials for the construction of energy devices, particularly organic solar cells. In the electrospinning process, polyacrylonitrile (PAN) has been utilized to generate nanofibers, which is the simplest and most popular method of creating carbon nanofibers (CNFs) followed by carbonization. The CNFs are coated on stainless steel (SS) plates and involve an electropolymerization process. The prepared Cu, CNF, CNF–Cu, PANI, PANI–Cu, CNF–PANI, and CNF–PANI–Cu electrode materials’ electrical conductivity was evaluated using cyclic voltammetry (CV) technique in 1 M H2SO4 electrolyte solution. Compared to others, the CNF–PANI–Cu electrode has higher conductivity that range is 3.0 mA. Moreover, the PANI, CNF–PANI, and CNF–PANI–Cu are coated on FTO plates and characterized for their optical properties (absorbance, transmittance, and emission) and electrical properties (CV and Impedance) for organic solar cell application. The functional groups, and morphology-average roughness of the electrode materials found by FT–IR, XRD, XPS, SEM, and TGA exhibit a strong correlation with each other. Finally, the electrode materials that have been characterized serve to support and act as the nature of the hole transport for organic solar cells.

The conventional multi-scale modelling approach that predicts carbon nanotube (CNT) growth region in heterogeneous flame environment is computationally exhaustive. Thus, the present study is the first attempt to develop a zero-dimensional model based on existing multi-scale model where mixture fraction z and the stoichiometric mixture fraction zst are employed to correlate burner operating conditions and CNT growth region for diffusion flames. Baseline flame models for inverse and normal diffusion flames are first established with satisfactory validation of the flame temperature and growth region prediction at various operating conditions. Prior to developing the correlation, investigation on the effects of zst on CNT growth region is carried out for 17 flame conditions with zst of 0.05 to 0.31. The developed correlation indicates linear ( zlb=1.54zst +0.11) and quadratic ( zhb=zst(7-13zst )) models for the zlb and zhb corresponding to the low and high boundaries of mixture fraction, respectively, where both parameters dictate the range of CNT growth rate (GR) in the mixture fraction space. Based on the developed correlations, the CNT growth in mixture fraction space is optimum in the flame with medium-range zst conditions between 0.15 and 0.25. The stronger relationship between growth-region mixture-fraction (GRMF) and zst at the near field region close to the flame sheet compared to that of the far field region away from the flame sheet is due to the higher temperature gradient at the former region compared to that of the latter region. The developed models also reveal three distinct regions that are early expansion, optimum, and reduction of GRMF at varying zst.

A carbon matrix for high-capacity Li/Na/K-alloy-based anode materials is required because it can effectively accommodate the variation in the volume of Li/Na/K-alloy-based anode materials during cycling. Herein, a nanostructured porous polyhedral carbon (PPC) was synthesized via a simple two-step method consisting of carbonization and selective acid etching, and their electrochemical Li/Na/K-ion storage performance was investigated. The highly uniform PPC, with an average particle size of 800 nm, possesses a porous structure and large specific surface area of 258.82 cm2 g– 1. As anodes for Li/Na/K-ion batteries (LIBs/NIBs/KIBs), the PPC matrix exhibited large initial reversible capacity, fast rate capability (LIB: ~ 320 mAh g– 1 at 3C; NIB: ~ 140 mAh g– 1 at 2C; KIB: ~ 110 mAh g– 1 at 2C), better cyclic performance (LIB: ~ 550 mAh g– 1; NIB: ~ 210 mAh g– 1; KIB: ~ 190 mAh g– 1 at 0.2C over 100 cycles), high ionic diffusivity, and excellent structural robustness upon cycling, which demonstrates that the PPC matrix can be highly used as a carbon matrix for high-capacity alloy-based anode materials for LIBs/NIBs/KIBs.

The nanostructured dysprosium oxide ( Dy2O3) was synthesized by the co-precipitation method and incorporated with graphitic carbon nitride (g-C3N4) using the ultrasonication method. The resultant product is denoted as Dy2O3/ g-C3N4 nanocomposite which was further used for electrochemical sensing of riboflavin (RF). The physicochemical properties of Dy2O3/ g-C3N4 nanocomposite were examined using several characterization techniques. The obtained results exhibit the nanocomposite formation with the preferred elemental compositions, functional groups, crystalline phase and desired surface morphology. The electrocatalytic performance of Dy2O3/ g-C3N4 nanocomposite was scrutinized with a glassy carbon electrode (GCE) via differential pulse voltammetry (DPV) and cyclic voltammetry (CV) techniques with the conventional three-electrode system. The modified electrode distributes more active surface area suggesting high electrocatalytic activity for the RF detection with two linear ranges (0.001–40 μM and 40–150 μM), a low detection limit of 48 nM and sound sensitivity (2.5261 μA μM−1 cm− 2). Further, the designed sensor possesses high selectivity, excellent stability, repeatability and reproducibility. Finally, the fabricated sensor was successfully estimated for the detection of RF in actual food sample analysis using honey and milk with better recovery.

A glassy carbon electrode modified with a composite consisting of electrodeposited chitosan and carboxylated multi-walled carbon nanotubes (e-CS/MWCNTs/GCE) was used as a working electrode for simultaneous determination of dopamine (DA), serotonin (5-HT) and melatonin (MT), which were related to circadian rhythms. The electrochemical characterizations of the working electrode were carried out via electrochemical impedance spectroscopy and chronocoulometry. It was found that electrochemical modification method, that was cyclic voltammetry, may can cause continuous CS polymerization on MWCNTs surface to form a dense membrane with more active sites on the electrode, and the electrochemically active surface area of e-CS/MWCNTs/GCE obtained was about 7 times that of GCE. The electrochemical behaviour of DA, 5-HT and MT on working electrode were carried out via differential pulse voltammetry and cyclic voltammetry. The results showed that e-CS/MWCNTs/GCE solved the problem that the bare electrode could not detect three substances simultaneously, and can catalyze oxidation potential difference as low as 0.17 V of two substances reaction at the same time, indicating very good electrocatalytic activity. By optimizing the detection conditions, the sensor showed a good linear response to DA, 5-HT and MT in the range of 20-1000 μmol/L, 9-1000 μmol/L and 20-1000 μmol/L, and the detection limits were 12 μmol/L, 10 μmol/L and 22 μmol/L (S/N = 3), respectively. In addition, the proposed sensor was successfully applied to the simultaneous detection of DA, 5-HT and MT in human saliva samples.

In the present study, an innovative electrochemical sensing platform was established for sensitive detection of NO2 —. This sensor was developed using CoFe alloy encapsulated in nitrogen-doped carbon nanocubes (named as CoFe@NC-NCS), synthesized through the calcination of polydopamine-coated CoFe Prussian-blue analogues (CoFe-PBA@PDA). The morphological and electrochemical characterization reveals that the CoFe@NC-NCS possesses high electrocatalytic activity for electrochemical quantitation of NO2 —, ascribed to the huge surface area and plentiful active positions, benefiting from the porous, hollow, and core–shell structure of CoFe@NC-NCS. Under the optimal conditions, CoFe@NC-NCS/GCE possessed remarkable sensing performance for NO2 — with wide liner ranges and a detection limit of 0.015 μM. NO2 — recovery experiments in real samples exhibited recoveries in the range of 98.8–103.5%. Hence, the CoFe@NC-NCS shows great promise for the construction of electrochemical sensor with more potential application.

To improve the thermophysical properties of Al alloy for thermal management materials, the Cu-coated carbon fibers (CFs) were used as reinforcement to improve the thermal conductivity (TC) and the coefficient of thermal expansion (CTE) of Al-12Si. The CFs reinforced Al matrix (CFs/Al) composites with different CFs contents were prepared by stir casting. The effects of the CFs volume fraction and Cu coating on the microstructure, component, TC and CTE of CFs/Al composites were investigated by scanning electron microscopy with EDS, X-ray diffraction, thermal dilatometer and thermal dilatometer. The results show that the Cu coating can effectively improve the interface between CFs and the Al-12Si matrix, and the Cu coating becomes Al2Cu with Al matrix after stir casting. The CFs/Al composites have a relative density greater than 95% when the volume fraction of CFs is less than 8% because the CFs uniform dispersion without agglomeration in the matrix can be achieved by stir casting. The TC and CTE of CFs/Al composites are further improved with the increased CFs volume fraction, respectively. When the volume fraction of CFs is 8%, the CFs/Al composite has the best thermophysical properties; the TC is 169.25 W/mK, and the CTE is 15.28 × 10– 6/K. The excellent thermophysical properties of CFs and good interface bonding are the main reasons for improving the thermophysical properties of composites. The research is expected to improve the application of Al matrix composites in heat dissipation neighborhoods and provide certain theoretical foundations.