본 연구에서는 IMO의 향후 예상 규제 물질 중 하나인 수트를 선박용 엔진을 대상으로는 최초로 배기 수트와 엔진 수트로 구분 하여 구조적 특성의 비교 분석을 시도하였다. 그리고 최근 발표되고 있는 배기 수트 재활용 연구의 연장선상에서 엔진 수트의 재활용 가 능성 여부를 확인하기 위하여 2,000℃로 열처리를 시행하였고, 열처리 전·후의 수트를 고분해능 전자현미경과 라만분광법을 통해 분석하 였다. 전자 현미경을 통한 분석 결과, 배기 수트와 엔진 수트는 유사한 형태의 나노 구조를 가지고 있으나, 배기 수트는 구형의 1차 입자 가 체인형 결합구조를 가지고 있었고, 엔진 수트는 배기 수트에 비해 무정형한 구조가 확인되었다. 라만분광법 분석 결과, 배기 수트와 엔 진 수트 모두 D peak(1,350 cm-1)와 G peak(1,580 ~ 1,600 cm-1)가 확인되었다. 다만, G/D ratio는 엔진 수트에 비해 배기 수트가 상대적으로 높게 나타나며, 이는 배기 수트가 더 흑연화 된 구조를 나타냄을 의미한다. 열처리 후의 분석 결과, 엔진 수트도 배기 수트와 유사하게 흑연화 가 문제없이 진행됨을 확인하였고, 이를 통해 선박용 디젤엔진에서 발생하는 배기 수트와 엔진 수트 모두 흑연재료로 재활용이 가능함을 확인하였다.

In this study, the effect of various pilot injection timings on combustion and emission characteristics were investigated in a common-rail direct injection (CRDI) diesle engine fueled with diesel-ethanol blends. The engine speed and engine load were controlled at constant 1500rpm and 70Nm, respectively. The tested fuels were DE0 (pure diesel fuel), DE5 (5 vol.% ethanol blended with 95 vol.% diesel oil), DE10 (10 vol.% ethanol blended with 90 vol.% diesel oil) and DE15 (15 vol.% ethanol blended with 85 vol.% diesel oil). The main injection timing was fixed at 0°CA TDC (top dead center), while various pilot injection timings including 25°CA BTDC (before top dead center), 20°CA BTDC and 10°CA BTDC were selected as the experimental variable. The experimental results showed that various pilot injection timings had little effect on the peak value of cylinder pressure, but had great influence on the start of combustion. The peak value of heat release rate (HHR) increased with the increase of ethanol content. However, the peak value of HRR reduced as the pilot injection is delayed. The diesel fuel containing 10% ethanol had a highest peak value of combustion pressure compared with the others, while the pilot injection timing occurred at 25°CA BTDC. On the other hand, the exhaust emissions of DE10 was also the lowest compared with the others. In addition, with the increase of ethanol content in diesel the PM and NOx emissions reduced.

미세먼지발생 문제는 커다란 사회적 문제로 대두되고 있다. 선박에서는 주 추진 동력원으로 디젤엔진을 주로 사용하고 있다. 본 연구에서는 디젤엔진에서 발생하는 미세먼지로 알려진 입자상 물질을 줄이기 위해서 디젤엔진의 후처리시스템으로 사용 중인 DPF(디 젤미립자 필터, Diesel particulate filter)를 소개하고자 한다. DPF의 소재로는 Cordierite와 SiC (Silicon carbide)의 두 가지가 사용되고 있다. 본 논문에서는 SiC DPF에 사용되는 접합제의 물성 향상을 위해서 기존 접합제로 사용된 SiC 계열의 물질 대신 코디얼라이트를 사용하여 열 팽창계수 변화를 통한 고온 변형에 대한 열 내구성을 평가하였으며, 접합제와 Segment 사이의 결합을 결정짓는 바탕제에 주성분인 실리카 졸의 pH 변화에 따른 물성 변화를 확인하였다. 이를 기반으로 실리카 졸의 반응성을 높이기 위해 Siline계 커플링제를 첨가하거나 SiC를 일부 첨가함으로써 접합제의 물성 변화의 영향에 대해서 실험을 통하여 확인하였다.

본 논문에서는 선박용 디젤엔진의 미세먼지저감 장치에 장착된 다공판 및 믹서의 형상과 배치에 따른 압력강하와 유동균일도 특성에 대한 연구를 진행하였다. 미세먼지저감 장치에 장착된 다공판 및 믹서는 미세먼지저감 장치 내의 배출가스 및 산화/환원제의 유동 균일도를 높여 배출가스 저감 성능을 높이는 긍정적인 효과와 함께 시스템의 배압을 상승시키는 부정적인 효과도 동시에 지니고 있다. 본 연구에서는 5개의 다공판, 1개의 믹서를 Case 별로 조합하여 6개의 사양에 대해서 유동해석을 통해 각각 유동균일도 및 압력 강하를 계산하였으며, 최적의 다공판 및 믹서의 형상과 배치를 선정하였다.

In this study, to investigate the effect of physical and chemical properties of butanol on the engine performance and combustion characteristics, the coefficient of variations of IMEP (indicated mean effective pressure) and fuel conversion efficiency were obtained by measuring the combustion pressure and the fuel consumption quantity according to the engine load and the mixing ratio of diesel oil and butanol. In addition, the combustion pressure was analyzed to obtain the pressure increasing rate and heat release rate, and then the combustion temperature was calculated using a single zone combustion model. The experimental and analysis results of butanol blending oil were compared with the those of diesel oil under the similar operation conditions to determine the performance of the engine and combustion characteristics. As a result, the combustion stabilities of D.O. and butanol blending oil were good in this experimental range, and the indicated fuel conversion efficiency of butanol blending oil was slightly higher at low load but that of D.O. was higher above medium load. The premixed combustion period of D.O. was almost constant regardless of the load. As the load was lower and the butanol blending ratio was higher, the premixed combustion period of butanol blending oil was longer and the premixed combustion period was almost constant at high load regardless of butanol blending ratio. The average heat release rate was higher with increasing loads; especially as butanol blending ratio was increased at high load, the average heat release rate of butanol blending oil was higher than that of D.O. In addition, the calculated maximum. combustion temperature of butanol blending oil was higher than that of D.O. at all loads.

최근 지구의 기후변화는 온실가스가 원인으로 전 세계적 대기환경문제로 크게 부각되고 있다. 국내에서도 기후변화에 적극 대응하기 위한 기술개발이 꾸준히 진행되고 있다. 날씨의 이상고온으로 인한 환경에 미치는 영향과 갑작스런 집중호우가 환경에 미치는 영향을 대상으로 하였다. 우리생활 주변 대기온도가 상승하였을 때 온도변화에 의한 대기오염발생에 미치는 영향을 연구하고자 한다. 본 연구의 실험조건은 선박 디젤기관에서 회전수 1400 rpm, 1600 rpm 그리고 1800 rpm, 부하는 0 %에서 25 %씩 100 %까지 하였고, 흡기 온도변화 는 20℃에서 50℃까지 구분하여 연구하였다. 연구한 결과 흡기온도가 증가함에 따라 일산화탄소 및 탄화수소는 약간 감소하였으나 연료 소비율, 질소산화물, PM은 약간 증가하였다. 또한 연소온도는 큰 변화가 없었다.

The fuel used in this study, DMM is an oxygen additive containing 42.5% oxygen by weight and dissolved in diesel fuel, also known as methyl alcohol or Dimethoxymethane (CH3-O-CH2-O-CH3). DMM, which is a colorless liquid, shows chemical characteristics of gas-liquid and is also used as a diesel fuel component. In this study, five mixtures were added to the common diesel fuel at DMM addition rates of 2.5, 5, 7.5, 10 and 12.5% by volume. A single cylinder, four strokes, DI diesel engine was used as the test engine. Experimental data were also collected at 24 engine speed-load conditions operating in steady state. The purpose of this experiment was to study the effect of the addition ratio of oxidized fuel mixed in diesel fuel on engine power and exhaust performance. When compared with the common diesel fuel, the exhaust of Smoke was substantially reduced in all DMM mixing ratios. These results indicate that DMM can be an effective blend of diesel fuel and is an environmentally friendly alternative fuel. This study also shows that smoke and NOx emissions can be reduced at the same time through the application of oxygen fuel and EGR.

The purposes of improving air pollution and suggesting energy resources have intensified research on various alternative energy for diesel combustion engines to solve severe environmental influences caused by air pollution. In this study, the applicable possibility of biodiesel and oxygenates (EGBE) was investigated as a cuspy method on decreasing the smoke emission. The smoke emission of blending fuel (biodiesel and EGBE) was reduced in comparison with commercial diesel fuel and it was reduced almost 63% at 2000 rpm, full load. But torque and brake specific energy fuel consumption rate didn't have any large changes. Also, the effectiveness of exhaust gas recirculation (EGR) for the reduction of NOx emission has been investigated. It was shown that simultaneous reduction of NOx and smoke emission was achieved with biodiesel(90%), oxygenates (10%) and cooled EGR rates (10%) in an IDI diesel engine.

In this paper, we investigate the relationship between fuel injection quantity and voltage and current energy of Bosch system and Delphi system by measuring the high and low voltage waveform, current waveform, fuel injection quantity and fuel pressure of A and J-engines. Waveform measurements are made using the PICO scope and the CDS tester. The injectors of A and J engines were tested under no load condition using injector with normal fuel injection quantity, injector with small fuel injection quantity and injector with many fuel injection quantity. In case of normal injector, A-engine has higher fuel pressure, injection interval time, voltage energy, and current energy than J-engine. The current energy of the A-engine changed linearly compared to that of the J-engine. For over and under injectors, the change in the previous physical quantity was greater for the A-engine than for the J-engine. However, the duration time of maintaining to open the injector is controlled differently, and so the voltage and current energy values are changed, and the change of the current energy is larger than the voltage energy.

The wavy fins have been widely used in the heat exchangers in coolering system, aerospace system and automotive. Especially, an automobile has the wavy fin and flat tube heat exchanger for oil cooling system. The objective of this research is the performance comparison of wavy fins for battle vehicle diesel engine oil-cooler by numerical analysis. The real type fin is the wavy fin with corrugated structure, and the comparative fin surfaces are plain, louver, lateral perforation and parallel wavy fin. The non-dimensional values of f-factor, j-factor, area goodness factor and volume goodness factor was performed on the performance comparison. The plain and louver fin shows the highest performance in pressure drop and heat transfer respectively. In the area goodness factor and volume goodness factor results, the parallel wavy fin and louver fin show the highest values at each result.

This paper investigates the relationship of voltage and current waveform between normal piezo injector and deterioration abnormal piezo injector. The experimental methods using Pico oscilloscope and GDS scan tool are employed to measure current and voltage waveform and fuel pressure of piezo injector. The experiment is carried out during no-load condition. A summary of the important results are as follows. 1) In case of normal injector, the fluctuation of duration time of piezo injector was linearly and regularly decreased with increasing engine speed, but the that of deterioration piezo injector was irregularly decreased with increasing engine speed. 2) In main injection, the peak value of the current waveform of abnormal injector was larger than that of normal injector, the duration time of deteriorated abnormal injector was less than that of normal injector at 800rpm and 1500rpm, but the duration time of deteriorated abnormal injector was larger than that of normal injector at 2000rpm and 3000rpm. This irregularity appears to be caused by the deterioration of the injector.