우리나라는 기상 악화 속에서 감항성이 확보된 선박만이 항해할 수 있도록 선박출항을 해사안전법에 근거하여 통제하고 있으 나 통제 대상선박 지정에 대한 과학적 평가 결과 및 정량적 근거가 미비하여, 항행안전의 확보와 합리적 출항통제 운영을 위한 개선 의견 이 제기되고 있다. 본 연구는 풍랑 주의보 발효 시 주요 통제대상 선종인 예인선의 실선계측을 통해, 현행 출항통제 기준의 적정성을 평 가하고 현실성 있게 개선될 수 있도록 정량적 근거를 제시하는 것에 연구 목적이 있다. 이를 위해 예인선에 선박의 3축 운동과 선체가속 도를 측정하는 Sensor를 설치하여 유의파고 3m인 해역 내에서 운항하여 선체운동 성능을 계측하였고, 계측된 수치를 내항성능 평가요소 및 한계 값 기준을 바탕으로 비교 분석하였다. 실측 선박은 톤수에 따른 현행 통제기준에서 제외되었으나, 분석 결과 Pitch 값이 Operation 기준을 넘어 항행안전에 위험성이 존재하였다. 본 연구 결과는 선박 출항통제 대상에 대한 검토와 다양한 선종 및 제원을 대표할 수 있는 추가적 실측연구가 필요함을 시사한다.

본 연구에서는 KBC2022의 풍직각방향 변동풍하중 스펙트럼을 이용하여 풍직각방향 풍하중을 생성하고 생성된 풍직각방향 풍하 중이 작용하는 구조물의 비탄성 동적거동을 해석하는 프로그램을 개발하고자 한다. 풍응답은 일차 모드가 탁월하고 소성화에 의한 진동의 변화는 작고, 풍방향 진동과 풍직각방향 진동은 독립적이며, 비틀림 진동의 영향은 작다고 가정한다. 적용 구조물을 수평방향 의 단자유도 모델로 가정하고, 구조물의 질량을 집중질량으로 치환하여 상부에 작용시킨다. 비탄성 해석을 위한 이력모델은 이선형 모델을 적용한다. 강성비()와 항복점비()를 변수로 비탄성 동적응답을 분석한 결과 강성비가 일정한 경우에 항복점비가 증가할수 록 최대변위비는 감소하다가 최소값을 나타내고 증가하는 것으로 나타났다. 강성비가 0.5이상인 경우 최대변위비가 1이하가 되는 항 복점비가 존재하며, 이는 비탄성 내풍설계시 비탄성 거동을 허용하더라도 탄성설계된 건물보다 최대 변형이 감소함을 나타낸다.

본 연구에서는 무인항공기인 드론을 활용한 VDMS(Vision-based Displacement Measurement System)를 통해 동적변위계측 정 확도와 동특성 추정 신뢰성 검증을 위한 동적실험을 실시하였다. 비행하는 드론의 이동 및 회전진동을 보정하기 위해 영상 내부의 변 위가 발생하지 않는 고정점을 활용한 보정밥법을 사용하였으며, 검증을 위해 설치한 범용 센서인 LVDT와 LDS의 변위계측 결과와 비 교하여 그 오차를 시간영역과 진동수영역에서 분석하였다. 3가지 타입의 장비 모두 최대 변위 도달 및 주기 운동 계측에 있어서 대체 적으로 유사한 결과를 나타내었다. LDS 기준의 오차 분석 결과, 드론과 LVDT는 가진 진동수 변화에 의한 오차 값은 미비하나, 최대 발생 변위가 작을수록 오차 값은 증가하였다.

Since the time to consider when evaluating leakage of spent fuel dry storage systems is very long, assumptions that continue to leak at the initial leakage rate are too conservative. Therefore, this study developed a dynamic methodology to calculate the change in leakage rate using time-varying variables and apply it to calculate the amount of radioactive leakage during the evaluation period. The developed dynamic methodology was then applied to calculate the leakage radiation source term for a hypothetical dry storage system and used to perform a public dose assessment. When applying the developed dynamic leakage rate evaluation methodology for more accurate confinement evaluation in case of containment damage of dry storage system, it was found that the change of leak rate with time is very insignificant if the hole diameter is small enough, and the leak rate decreases rapidly with time when a hole with a certain diameter or larger occurs. In the case of the accident condition, except when the hole is very large, it corresponds to the chocked flow condition, and the leak rate decreases rapidly as soon as the internal pressure is sufficiently lowered to enter the molecular and continuum flow region. In the case of a small hole diameter, the leakage volume is very small, so even if the dynamic methodology is applied, the evaluation results are not different from the case where the initial leakage rate continues, and when the hole diameter exceeds a certain value, the internal pressure drops according to the leakage volume, and the leakage rate decreases significantly. As a result of evaluating the dose to residents by applying the calculated radiation source term, it was confirmed that the dose criteria was exceeded when a hole with a diameter of about 4 μm occurred under off-normal conditions, and the dose standard was exceeded under accident conditions when a chocked flow occurred between the diameter of the hole and 2-3 μm, resulting in a rapid increase in the dose. The results of this study are expected to contribute to a more accurate evaluation of the confinement performance of storage systems, which will contribute to the design of optimal dry storage systems.

For Korean nuclear fuel cycle project, it is necessary to design and evaluate the integrity of spent fuel storage. For the design and evaluation of spent fuel storage, it is necessary to evaluate the properties of various materials used in spent fuel storage. The materials previously considered in the design of nuclear power plants were limited to static properties and were listed in design and manufacturing code and standards. However, for the evaluation of the storage containers in scenarios such as transportation and events, dynamic material property evaluations are required. Research on the dynamic properties of materials is generally conducted in the fields of automotive and aerospace, and most of the studies are on metal materials under sheet conditions. Since the structural materials of the storage containers for used nuclear fuel are mostly composed of thick materials, consideration should be given to property evaluation methodology and quantitative comparison. In this study, the mechanical properties of stainless steel material with canister application were evaluated according to the strain rate, and the crack resistance evaluation was also performed. It was confirmed the changes in strength and crack resistance according to the increase in strain rate and observed differences in microstructural hardening behavior.

이 논문에서는 보행교의 진동 사용성 평가에 있어서 보행자의 이동 질량 관성 효과의 고려 여부, 보행 패턴 등을 고려한 보행 시나 리오 등에 따른 해석 결과를 제시하고, 그에 따라 보행교 설계 단계에서 동적 유한요소 해석을 통한 진동 사용성 평가에 있어 적절한 해석 방법과 유의점을 제안한다. 지간 40m의 강합성 박스 단면을 갖는 단경간 단순교 형식의 보행교에 대하여 보행자 밀도, 보행 속 도, 임의 보행, 동기화 보행 등을 고려한 보행 시나리오에 대한 가속도 응답을 분석한다. 해석 결과 고정 질량 해석 방법은 임의 보행 시 나리오 해석에서 이동 질량 해석과 큰 차이를 보이지 않으며 진동 사용성 평가시에는 더 넓은 진동수 대역을 가진할 수 있는 임의 보행 시나리오를 고려하는 것이 바람직할 수 있음을 보였다.

PURPOSES : Advancements in science and technology caused by industrialization have led to an increase in particulate matter emissions and, consequently, severity of air pollution. Nitrogen oxide (NOx), which accounts for 58% of road transport pollutants, adversely affects both human health and the environment. A test-bed was constructed to determine NOx removal efficiency at the roadside. TiO2, a material used to reduce particulate matter, was used to remove NOx. It was applied to a vertical concrete structure using the dynamic pressurized penetration TiO2 fixation method, which can be easily applied to vertical concrete structures. This study was conducted to evaluate the NOx removal efficiency of the dynamic pressurized-penetration TiO2 fixation method in a test-bed under real roadside conditions. METHODS : A test-bed was constructed in order to determine the NOx removal efficiency using the dynamic pressurized penetration TiO2 fixation method on the roadside. The dynamic pressurized-penetration TiO2 fixation method was applied by installing a vertical concrete structure. NOx was injected into the test-bed using an exhaust gas generator. By installing a shading screen, the photocatalytic reaction of TiO2 was suppressed to a maximum concentration of 1000 ppb along the roadside. The removal efficiency was evaluated by measuring NOx concentrations. In addition, illuminance was measured using an illuminance meter. RESULTS : From the results of the analysis of the NOx removal efficiency in the test-bed which the dynamic pressurized type TiO2 fixation method was applied to, an average removal efficiency ranging from 18% to 40% was achieved, depending on the illuminance. Similarly, according to the results of the evaluation of the NO removal efficiency, an average of removal efficiency ranging from 20% to 62% was achieved. Thus, the NOx removal efficiency increased when the illuminance was high. CONCLUSIONS : From the results of the experiment conducted, the efficiency of NOx removal per unit volume was obtained according to the illuminance of TiO2 concrete along an actual road. Field applicability of the dynamic pressurized-penetration-type TiO2 fixation method to vertical concrete structures along roads was confirmed.

Background: Core muscle weakness occurs due to trunk asymmetry and spinal malalignment after stroke. Core exercise is being implemented to improve trunk control and sitting position in stroke patients. Objectives: To investigated the effects of core muscle electrical stimulation on trunk control and dynamic balance in stroke patients. Design: Quasi-experimental study. Methods: A total of 30 stroke patients were recruited and divided into two groups: experimental group (core muscle electrical stimulation group) and control group (sham core muscle electrical stimulation group). Trunk impairment scale (TIS) was used to measure trunk control. BioRescue was used to measure sitting dynamic balance. Results: In both groups, all TIS scores and sitting dynamic balance abilities were improved increased significantly after intervention (P<.05). Changes in TIS scores and sitting dynamic balance abilities were significantly greater in the experimental group than the control group (P<.05). Conclusion: It was found that core muscle electrical stimulation can be used as an effective method for trunk control and balance recovery in stroke patients.

Background: Despite its high prevalence, interventions in plantar fasciitis remain inconclusive. To improve the daily life of plantar fasciitis patients, it is necessary to identify appropriate interventions to improve pain and foot pressure and balance. Improving the interventions for plantar fasciitis is one of the main goals for rehabilitation. Objectives: To investigate the changes in pain and static-dynamic foot pressure and balance through the evaluation of 42 plantar fasciitis patient before and after the foot stretching and joint mobilization interventions. Design: Randomized controlled trial. Methods: The 42 subjects of the study were divided into a stretching group and a joint mobilization group with 21 subjects being assigned to each group. The results before and after the experiment were analyzed by applying stretching and joint movement interventions for a total of 6 weeks. Results: Before and after the intervention, there were significant improvements in the pain index and static-dynamic foot pressure and static balance in both stretching and joint mobilization groups. However, the between-group comparison indicated no significant differences. Conclusion: The stretching and the joint mobilization can improve the pain and static-dynamic foot pressure and static balance in plantar fasciitis patients.

본 논문은 코시 모멘텀(Cauchy’s Momentum) 방정식을 이산화하기 위해 GC-LSM(Geometric Conservative Least Squares Method) 을 사용한 새로운 Meshless 방법을 제시한다. FEM(Finite Element Method) 방법이 구조해석에 널리 사용되고 있지만 무격자 기법은 격자를 이동해야 할 때 장점이 많기 때문에 개발되었다. 본 작업은 무격자 기반의 FSI(Fluid-Structure Interaction) 프로그램을 개발하 기 위한 기틀을 다지는 단계이다. 본 논문에서는 Cauchy’s Momentum 방정식을 GC-LSM을 사용하여 강형식 형태로 이산화하였고, 시간 적분을 위해 New Mark Beta 방법을 사용하였다. 개발된 기법은 1D, 2D 및 3D 벤치마킹 문제에서 검증했으며, 정적 해석 및 동적 해석 결과가 해석해와 비교시 매우 정확한 결과를 보여준다.

철도교량의 설계는 장기간에 걸쳐 수행되고 대규모의 부지를 대상으로 하기 때문에 다양한 환경적인 요인과 불확실성을 동반하게 된다. 이러한 연유로 초기 설계단계에서 충분히 검토하였더라도 설계변경이 종종 발생하고 있다. 특히 철도교량과 같은 대규모 시설 물의 설계변경은 많은 시간과 인력을 소모하며, 매번 모든 절차를 반복하는 것은 매우 비효율적이다. 본 연구에서는 딥러닝 알고리즘 중 전이학습을 통해 설계변경 전의 학습 결과를 활용하여 설계변경 후의 학습의 효율성을 향상시킬 수 있는 기법을 제안하였다. 분석 을 위해 기개발한 철도교량 딥러닝 기반 예측 시스템을 활용하여 시나리오들을 작성하고 데이터베이스를 구축하였다. 제안된 기법은 설계변경 전 기존 도메인에서 학습에 사용한 8,000개의 학습데이터 대비 새로운 도메인에서 1,000개의 데이터만을 학습하여 유사한 정확도를 나타내었고 보다 빠른 수렴속도를 가지는 것을 확인하였다.

본 연구에서는 투과 유량 모델을 개발하기 위하여, 시간, 막 전후의 압력 차, 회전 속도, 막의 기공 크기, 동점도, 농도 및 공급 유체의 밀도 등 7개의 입력 변수에 기반한 두 종류(ANN 및 SVM) 인공지능 기법을 이용하였다. 시행착오법과 실험데이터와 예측 데이터 간의 결정 계수(R2) 와 평균절대상대편차(AARD)를 포함한 두 가지 통계 변수를 통해 최적의 모델 을 선정하였다. 최종적으로 얻어진 결과에서 최적화된 ANN 모델이 R2 = 0.999 및 AARD% = 2.245인 투과 플럭스 예측 정 확도를 보여서, R2 = 0.996 및 AARD% = 4.09의 정확도를 보인 SVM 모델에 비해 더 정확함을 알 수 있었다. 또한, ANN 모델은 SVM 방식에 비해 투과 유속을 예측하는 능력도 더 높은 것으로 나타났다.

To seek an atmospheric heating mechanism operating on the Sun we investigated a heating source generated by a downflow, both of which may arise in a magnetic loop dynamically formed on the Sun via flux emergence. Since an observation shows that the illumination of evolving magnetic loops under the dynamic formation occurs sporadically and intermittently, we performed a magnetohydrodynamic simulation of flux emergence to obtain a high-cadence simulated data, where temperature enhancement was identified at the footpoint of an evolving magnetic loop. Unlike a rigid magnetic loop with a confined flow in it, the evolving loop in a low plasma β atmosphere is subjected to local compression by the magnetic field surrounding the loop, which drives a strong supersonic downflow generating an effective footpoint heating source in it. This may introduce an energy conversion system to the magnetized atmosphere of the Sun, in which the free magnetic energy causing the compression via Lorentz force is converted to the flow energy, and eventually reduced to the thermal energy. Dynamic and thermodynamic states involved in the system are explained.

In this paper, the effect of a dynamic vibration absorber to suppress the response of a base excitation vibration system composed of a cubic nonlinear spring and a friction damper is investigated. And the dynamic absorber consists of a linear spring and a viscose damper. The mathematical models of these systems are governed by second order nonlinear ordinary differential equations. The response characteristics of the system are analyzed using the slowly changing phase and amplitude(SCPA) method, which is one of the averaging methods. As a function of the friction force ratio, It was obtained the locking frequency at which the relative motion starts was obtained, and the regions where the locking occurred. The displacement transmissibility was investigated according to the change of the design parameter, and the optimal design parameters could be found to minimize the displacement transmissibility.