Nitrogen-doped titanium dioxide (N-doped TiO2) is attracting continuously increasing attention as a material for environmental photocatalysis. The N-atoms can occupy both interstitial and substitutional positions in the solid, with some evidence of a preference for interstitial sites. In this study, N-doped TiO2 is prepared by the sol–gel method using NH4OH and NH4Cl as N ion doping agents, and the physical and photocatalytic properties with changes in the synthesis temperature and amount of agent are analyzed. The photocatalytic activities of the N-doped TiO2 samples are evaluated based on the decomposition of methylene blue (MB) under visible-light irradiation. The addition of 5 wt% NH4Cl produces the best physical properties. As per the UV-vis analysis results, the N-doped TiO2 exhibits a higher visible-light activity than the undoped TiO2. The wavelength of the N-doped TiO2 shifts to the visible-light region up to 412 nm. In addition, this sample shows MB removal of approximately 81%, with the whiteness increasing to +97 when the synthesis temperature is 600℃. The coloration and phase structure of the N-doped TiO2 are characterized in detail using UV-vis, CIE Lab color parameter measurements, and powder X-ray diffraction (XRD).

Reactive oxygen species (ROS) can be produced by interactions between sunlight and light-absorbing substances in natural water environments and can completely destroy various organic pollutants in waste water. In this study, we used graphene oxide modified Ag2Se nanoparticles to enhance photochemically generated oxygen (PGO) species activity. Surface area and pore volumes of the Ag2Se-graphene (Ag2Se-G) samples showed catastrophic decrease due to deposition of Ag2Se. The generation of reactive oxygen species was detected through the oxidation reaction of DPCI to DPCO. The photocurrent density and the PGO effect increase in the case of the use of modified graphene. The PGO effect of the graphene modified with Ag2Se composites increased significantly due to a synergetic effect between graphene and the Ag2Se nanoparticles. The photocatalytic activity of sample was evaluated by measuring the degradation of organic pollutants such as methylene blue (MB) and industrial dyes such as Texbrite BA-L (TBA) under visible light.

본 연구의 목적은 2011년 4월 22일부터 10월 22일까지 우리나라에서 강수가 있는 총 75일 동안 COMS 위성의 적외 채널 10.8 μm 휘도 온도(IR), 적외 채널 10.8 μm와 수증기 채널 6.7 μm의 휘도 온도차(IR-WV), 정규화 된 가시 반사도(VIS)와 기상 레이더의 강우강도를 이용하여 2-D와 3-D 대류운의 강우강도 (CRR) 조견표를 향상시키는 것이다. 특별히 한국형 2-D와 3-D CRR 조견표를 검증하기 위해 2011년 강수가 있는 24일 동안의 기상 레이더 강우강도 자료 가 사용된다. 2-D와 3-D CRR 조견표는 각 채널의 등급 범주별 강우 총수와 비강우 총수의 행렬을 이용하여 구한 강 우 확률에 평균 누적강우강도와 최대 강우강도를 각각 곱함으로써 2-D (IR, IR-WV)와 3-D (IR, IR-WV, VIS) 조견표 의 기본과 최대 행렬을 얻을 수 있다. 최종적으로 새로운 2-D와 3-D의 CRR 조견표는 경험적으로 기본과 최대 강우강 도 행렬의 회귀 분석으로 얻어진다. 그 결과 새로운 CRR 조견표는 기존보다 낮은 IR 휘도 온도, 낮은 IR-WV 휘도 온 도차일 때에도 비교적 많은 강우 현상을 나타내며, 10 mm h−1 이상의 강우강도 영역이 확대되어 나타난다. 정확도와 범 주별 통계가 주어진 기간 동안 발생했던 CRR 자료에 대해 계산된다. 새로운 2-D와 3-D CRR 조견표의 평균 오차, 평 균절대 오차, 제곱근평균 오차가 기존 조견표보다 작게 나타나며, 예측 거짓경고비율은 감소하고, 탐지확률은 증가하며, 임계성공지수는 개선된다. 태풍과 뇌우와 같은 기상 이변에서의 강한 호우를 고려하기 위해서 습윤 보정 계수를 교정한 다. 이 인자는 수치모델이나 COMS에서 복원한 지면에서 500 hPa까지 평균한 총가강수량과 상대습도의 곱 (PW·RH) 으로 정의된다. 이 연구에서는 PW·RH에 근거하여 IR 운정 휘도 온도가 210 K 이하일 때, 상대습도가 40% 이상일 때 1에서 2사이를 경험적으로 정한다. 새로운 2-D와 3-D CRR 조견표를 적용한 결과 평균 오차, 평균 절대 오차, 제곱근 평균 오차가 줄어든다.

Earthquake event keeps increasing every year, and the recent cases of earthquake hazards invoke the necessity of seismic study in Korea, as geotechnical earthquake hazards, such as strong ground motion, liquefaction and landslides, are a significant threat to structures in industrial hub areas including coastal facilities. In this study, systemized framework of integrated assessment of earthquake-induced geotechnical hazard was established using advanced geospatial database. And a visible simulation of the framework was specifically conducted at two coastal facility areas in Incheon. First, the geospatial-grid information in the 3D domain were constructed with geostatistical interpolation method composed of multiple geospatial coverage mapping and 3D integration of geo-layer construction considering spatial outliers and geotechnical uncertainty. Second, the behavior of site-specific seismic responses were assessed by incorporating the depth to bedrock, mean shear wave velocity of the upper 30 m, and characteristic site period based on the geospatial-grid. Third, the normalized correlations between rock-outcrop accelerations and the maximum accelerations of each grid were determined considering the site-specific seismic response characteristics. Fourth, the potential damage due to liquefaction was estimated by combining the geospatial-grid and accelerations correlation grid based on the simplified liquefaction potential index evaluation method.

An importance of food allergen detection has been growing in food industry. Here, we developed a rapid and easy-to-use detection system for Ara h1, a major allergen in peanut, using gold nanoparticles and switchable linkers. The detection system was performed by two steps. In the first step, Ara h1 was mixed with various concentrations (0.2 - 1.0μg/mL) of biotinylated anti-Ara h1 antibody (i.e., switchable linker, SLs) solutions for 20 min. After mixing, streptavidin coated gold nanoparticle (Abs. 4.0) was added to the mixture solutions with agitation for10 min. Without Ara h1(control), the region of aggregation caused by quantitative relationship between SLs and gold nanoparticle was observed at more than 0.4 μg/mL of SLs. However, under presence of Ara h1, SLs covered with Ara h1 had less ability to react with gold nanoparticles than naked SLs. This resulted in a change of the quantitative relationship mentioned above, which led to shift of the aggregation region. When 10 nM and 40 nM of Ara h1 were added, the aggregation region was appeared from 0.5and 0.8 μg/mLof switchable linkers, respectively. Ara h1 in peanut sample was also detected with this system. 0.4 μg/mL of switchable linkers are mixed with serially diluted peanut extract solutions. As a result, the shift of the aggregation region was observed from undiluted extract to 10 -2 diluted solution. This system could be adapted to detect other harmful/useful bio materials in food.

SnS-TiO2 nanocomposites are synthesized using simple, cheap, and less toxic SnCl2 as the tin (II) precursor. The prepared nanoparticles are characterized using powder X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-Vis diffuse reflectance spectra (DRS). The XRD and TEM results indicate that the prepared product has SnS nanoparticles and a grain diameter of 30 nm. The DRS demonstrate that SnS-TiO2 possesses the absorption profile across the entire visible light region. The generation of reactive oxygen species is detected through the oxidation reaction from 1,5-diphenyl carbazide (DPCI) to 1,5-diphenyl carbazone (DPCO). It is found that the photocurrent density and photocatalytic effect increase with the modified SnS. Excellent catalytic degradation of Texbrite BA-L (TBA) solution is observed using the SnS-TiO2 composites under visible light irradiation. It is proposed that both the strong visible light absorption and the multiple exciton excitations contribute to the high visible light photocatalytic activity.

This study is to develop the double capsulation technology in order to increase the conservativeness and stability of unstable materials such as vitamins, polyphenols, natural active ingredients. And also, best way of triple matrix capsulation using natural polymers were detail described. As the first capsulation with w/o/w (water-in-oil-in-water) emulsifying system, our study group was especially made to soft and moisture cream using 5wt% of sucrose ester emulsifier as first capsulation. Nutrient agents are squalane, camellia oil. Triple matrix capsulation was formed with the best stabilized bead type capsules when it blended of chitosan, algin, sodium-potassium alginate. The bead diameter size was about 2.0~4.5mm (mean diameter: 3.2mm). Activity of lactobacillus containing cream for depending on various pH variations showed that alkalinity (pH=10.8±0.5) condition was higher than acidity (pH=4.2±0.2) and neutrality (pH=7.1±0.3) conditions. After a month, it also was certified to the activity of lactobacillus in incubated at 37±1°C in culture medium. As application of food industry, we developed the containing lactobacillus capsule and 7 colored kinds of double and triple matrix capsulation in yogurt cream and active ingredients. As for above mentioned those results, one of tool to stabilize the living lactobacillus, doubled matrix capsulation greatly be expected to contribute to food industry. Furthermore, it can be expected to apply the drug delivery system (DDS) to active ingredients of stabilizing technologies at drug, pharmaceutical division and cosmetic industry, etc.

Cubic mesocrystal CeO2 was synthesized via a hydrothermal method with glutamic acid (C5H9NO4) as a template. The XRD pattern of a calcined sample shows the face-centered cubic fluorite structure of ceria. Transmission electron microscopy (TEM) and the selected-area electron diffraction (SAED) pattern revealed that the submicron cubic mesocrystals were composed of many small crystals attached to each other with the same orientation. The UV-visible adsorption spectrum exhibited the red-shift phenomenon of mesocrystal CeO2 compared to commercial CeO2 particles; thus, the prepared materials show tremendous potential to degrade organic dyes under visible light illumination . With a concentration of a rhodamine B solution of 20 mg/L and a catalyst amount of 0.1 g/L, the reaction showed higher photocatalytic performance following irradiation with a xenon lamp (≥ 380 nm). The decoloring rate can exceed 100% after 300 min.

The goal of this research was to develop a portable system that could be used to evaluate the quality of milk in real time at a raw milk production site. A real-time portable quality evaluation system for raw milk was developed to enable non-destructive quality evaluation of somatic cell count (SCC), fat, protein, lactose, and total solid (TS) in milk samples. A prediction model of SCC, fat, protein, lactose, and TS was constructed using partial least squares (PLS) and 200 milk samples were used to evaluate the prediction performance of the portable quality evaluation system and high performance spectroscopy. Through prediction model development and verification, it was found that the accuracy of high performance spectroscopy was 90% for SSC, 96% for fat, 96% for protein, 91% for lactose, and 97% for TS. In comparison, the accuracy of the portable quality evaluation system was relatively low, at 90% for SSC, 95% for fat, 92% for protein, 89% for lactose, 92% for TS. However, the measurement time for high performance spectroscopy was 10 minutes for 1 sample, while for the portable quality evaluation system it was 6 minutes. This means that the high performance spectroscopy system can measure 48 samples per day (8 hours), while the portable quality evaluation system can measure 80 (8 hours). Therefore, it was found that the portable qual ity evaluation system enables quick on-site quality evaluation of milk samples.

The most general photocatalyst, TiO2 and WO3, are acknowledged to be ineffective in range of visible light. Therefore, many efforts have been directed at improving their activity such as: band-gap narrowing with non-metal element doping and making composites with high specific surface area to effectively separate electrons and holes. In this paper, the method was introduced to prepare a photo-active catalyst to visible irradiation by making a mixture with TiO2 and WO3. In the TiO2-WO3 composite, WO3 absorbs visible light creating excited electrons and holes while some of the excited electrons move to TiO2 and the holes remain in WO3. This charge separation reduces electron-hole recombination resulting in an enhancement of photocatalytic activity. Added Ag plays the role of electron acceptor, retarding the recombination rate of excited electrons and holes. In making a mixture of TiO2-WO3 composite, the mixing route affects the photocatalytic activity. The planetary ball-mill method is more effective than magnetic stirring route, owing to a more effective dispersion of aggregated powders. The volume ratio of TiO2(4) and WO3(6) shows the most effective photocatalytic activity in the range of visible light in the view point of effective separation of electrons and holes.

Excellent electron transport properties with enhanced light scattering ability for light harvesting have made well-ordered one dimensional TiO2 nanotube(TNT) arrays an alternative candidate over TiO2 nanoparticles in the area of solar energy conversion applications. The principal drawback of TNT arrays being activated only by UV light has been addressed by coupling the TNT with secondary materials which are visible light-triggered. As well as extending the absorption region of sunlight, the introduction of these foreign components is also found to influence the charge separation and electron lifetime of TNT. In this study, a novel method to fabricate the TNT-based composite photoelectrodes employing visible responsive CuInS2 (CIS) nanoparticles is presented. The developed method is a square wave pulse-assisted electrochemical deposition approach to wrap the inner and outer walls of a TNT array with CIS nanoparticles. Instead of coating as a dense compact layer of CIS by a conventional non-pulsed-electrochemical deposition method, the nanoparticles pack relatively loosely to form a rough surface which increases the surface area of the composite and results in a higher degree of light scattering within the tubular channels and hence a greater chance of absorption. The excellence coverage of CIS on the tubular TiO2 allows the construction of an effective heterojunction that exhibits enhanced photoelectrochemical performance.

AC and ZnS modified TiO2 composites (AC/ZnS/TiO2) were prepared using a sol-gel method. The composite obtained was characterized by Brunauer-Emmett-Teller (BET) surface area measurements, X-ray diffraction (XRD), energy dispersive X-ray (EDX) analysis, scanning electron microscope (SEM) analysis, and according to the UV-vis absorption spectra (UV-vis). XRD patterns of the composites showed that the AC/ZnS/TiO2 composites contain a typical single and clear anatase phase. The surface properties as observed by SEM present the characterization of the texture of the AC/ZnS/TiO2 composites, showing a homogenous composition in the particles showing the micro-surface structures and morphology of the composites. The EDX spectra of the elemental identification showed the presence of C and Ti with Zn and S peaks for the AC/ZnS/TiO2 composite. UV-vis patterns of the composites showed that these composites had greater photocatalytic activity under visible light irradiation. A rhodamine B (Rh.B) solution under visible light irradiation was used to determine the photocatalytic activity. The degradation of Rh.B was determined using UV/Vis spectrophotometry. An increase in the photocatalytic activity was observed. From the photocatalytic results, the excellent activity of the Y-fullerene/TiO2 composites for the degradation of methylene blue under visible irradiation could be attributed to an increase in the photo-absorption effect caused by the ZnS and to the cooperative effect of the AC.

분리막을 이용한 수처리 공정에서 유입 수에 함유된 부유물질이나 기타 오염물질이 막 표면 또는 내부에 축적 흡착 등의 막 오염현상으로 인해 막 성능 감소와 함께 막 분리 공정에 큰 영향을 미치게 된다. 본 연구에서는 막 표면에서의 막 오염현상을 실시간으로 모니터링 할 수 있는 기술을 연구하였다. 투명한 오염물질에 의한 분리막 표면 오염을 측정하기 위해 막 표면에 360 nm 파장의 가시광선을 조사하여 이미지를 R. G. B 값으로 추출하여 막의 오염현상을 실시간으로 모니터링 하였다. 추출된 이미지 중 400~499 nm 파장영역인 B 값이 가장 강도가 강하게 나타났다. 막 오염정도의 변화를 이미지의 강도 차이로 관찰함으로써 실시간 분석이 가능함을 확인하였다.

In this research, we were prepared the glazed ceramic samples by the change of the pigment content and investigated to reveal the standardized color. The chemical composition of the pigment was analyzed using a ICP-OES. XRF mapping and UV-Vis spectroscopy were used to evaluate the color property and surface homogeneity. The color development was observed as a result of analyzing the pigment content and change of the color. The pigment content and the spectral reflection showed the relation of the inverse proportion and the standardized color which could be revealed through analysis data.

A carbon doped (C-) photocatalyst, which shows good photocatalytic activity to Ultraviolet irradiation and visible irradiation, was successfully prepared by co-grinding of with ethanol or Activated Carbon(C), followed by heat treatment at in air for 60 min. Ethanol and C were used as a representative agent of liquid and solid for carbon doping. Their influence on improving photocatalytic ability and carbon doping degree was studied with degradation of methyl orange and XPS analysis. The product prepared by co-grinding of with Ethanol had Ti-C and C-O chemical bonds and showed higher photocatalytic activity than the product prepared by co-grinding of with C, where just C-O chemical bond existed. As a result, mechanochemical route is useful to prepare a carbon doped photocatalyst activating to visible irradiation, where the solid-liquid operation is more effective than solid-solid operation to obtain a carbon doped .