검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 152

        102.
        2005.03 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        원자력시설 핫셀 (Hot Cell)내에서 핵종실험 시 발생하는 고방사능 분진(Hot Particulate)의 크기는 0.5300 이고 주 핵종은 UO였다. 핫셀 내의 고방사능 분진을 제거하기 위해 사이클론과 Bag/HEPA필터로 구성된 장치를 고안하였고, 이 장치의 사이클론에 의해 고방사능 분진을 최대로 포집할 수 있는 실험조건을 제시했다. 모의입자의 크기가 클수록 입자의 포집효율은 높았다. 모의 입자의 크기가 5 이상일 때, 입자의 포집효율은 보다 높았다. 모의 입자의 크기가 1.0 보다 작을 때, 포집효율은 보다 작았다. 모의 입자의 유입속도가 12 m/sec보다 클 때, 포집효율은 보다 높았다. 그러나 유입속도가 17 m/sec 보다 클 때 포집효율의 증가율은 크지 않았다. 모의입자의 포집효율은 Vortex Finder의 길이가 7.2 cm이하일 때, 길이의 증가와 함께 높아졌지만 7.2 cm 이상일 때는 낮아지기 시작했다. 그러므로 Vortex Finder의 길이가 7.2 cm 일 때, 최대포집효율을 나타냈다. 사이클론 밑에 보조콘 부착 시 모든 속도 범위에서 약 평균 정도 포집효율이 증가하므로 보조콘 부착효과가 크지 않았다.
        4,000원
        104.
        2003.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Particulate leaching method for the preparation of porous PLLA scaffolds was carried out and especially, the effect of PLLA/CHCl3 solution concentration on the salt leaching rate and the pore structure of PLLA scaffolds were considered. It was found that maintaining lower PLLA/CHCl3 concentration and higher CHCl3 evaporation temperature in the preparation of PLLA/NaCl mixtures resulted in the enhancement of salt leaching rat e and higher porosity. This is understood that those conditions could minimize the formation of dense PLLA layer on the surface of PLLA/NaCl mixture as well as introducing better porosity on the surface. Higher salt leaching temperature accelerated the salt leaching rate but it seems that there is no influence on the porosity of PLLA scaffolds.
        4,000원
        105.
        2001.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        2000년 춘계에 한국 농촌지역인 충남 서산에서 대기부유분진(SPM)과 곰팡이포자의 관계에 대해 조사하였다. 부유분진의 농도는 1차 황사기간(3월 23-24일)에 199.8μg m-3, 2차 황사기간(4월 7-9일)에 249.4μg m-3, 비황사기간(5월 12-6일)에 98.9μg m-3으로 각각 나타났다. 2회의 황사기간들간에 부유분진 농도는 차이를 보였지만 5μm 정도의 입경 크기를
        4,000원
        106.
        2000.05 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        자전연소합성(SHS)법을 이용하여 탄소섬유와 티타늄, 지르코늄, 니오븀, 규소, 붕소, 중석, 몰리브덴의 분말로부터 여러 가지 섬유상 탄화물의 합성을 시도하였다. 티타늄과 지르코늄은 예열없이, 그 이외의 경우는 전기로 또는 화학로를 사용하여 예열하여 반응을일으킨 결과, TiC, ZrC, NbC, SiC, B4C, WC, Mo2C 의 순수한 탄화물의 형성되었다. TiC, ZrC, NbC 및 B4C 탄화물의 형상은 속의 빈 섬유상이었고, SiC는 보다 작은 입자와 미세 휘스커로 이루어진 섬유상을 하고 있었고 WC와 Mo2C 는 비섬유상을 하고 있었다. 여러 가지 형상의 원인에 대하여 합리적 설명을 시도하였으며 정성적 메카니즘을 제안하였다.
        4,000원
        107.
        1998.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구에서는 기지개와 미시구멍으로 구성된 복합재료에 입자보강 복합재료의 등가 재료상수 예측기법인 평균장 근사이론과 등가원리를 적용하여 위상 최적화에 필요한 등가 재료상수와 설계변수와의 상관관계식을 유도하였다. 또한, 유도된 관계식에 중간값을 갖는 설계변수의 수를 줄이기 위하여 벌칙인자를 도입하였다. 그리고 본 연구의 타당성을 검증하기 위하여 벌칙인자가 도입된 위상 최적화문제를 순차이차계획법인 PLBA 알고리즘을 이용하여 해석하였다.
        4,000원
        108.
        1998.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        경유자동차에서 발생하는 입자상물질은 대기오염의 주범으로 인식되어 국내외적으로 이의 규제가 점점 강화되고 있다. 본 고에서는 전 호에 이어 이러한 입자상물질을 제거하기 위하여 가장 보편적으로 사용되는 필터인 세라믹 하니컴 필터에서의 기공 및 필터특성의 조절과 설계에 대하여 언급하였다. 또한 그 외 각종 필터, 즉 세라믹 화이버 캔들 필터, 세라믹 폼 필터, 세라믹 크로스 플로우 필터 그리고 금속 필터 등의 성능 및 제조방법을 정리하였다. 이와같이 후처리장치용 필터로는 수없이 많은 필터들이 개발되어 많은 실증시험을 거치고 있으나 이러한 필터의 본격적인 상용화를 위하여는 재료 측면에서의 보다 많은 연구, 개발이 뒤따라야 할 것으로 판단된다.
        4,300원
        109.
        1998.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In purpose of introducing the inverse magnetostrictive properties into the structural ceramics, based nanocomposites dispersed with nano-sized Ni-Co particles were studied. The composites were fabricated by the hydrogen reduction and hot-pressing of and NiO-CoO mixed powders. The mixtures were prepared by using Ni- and Co-nitrate as source materials for the Ni-Co particles. Microstructural observations revealed that nano-sized Ni-Co particles were dispersed homogeneously at grain boundaries. High strength above 1 GPa was obtained for the wt% Ni-Co nanocomposite fabricated by a controlled powder preparation process. The inverse magnetostrictive response to applied stress was obtained due to the presence of dispersed Ni-Co particles, which indicates a possibility to incorporate new functions into the structural ceramics without loosing the mechanical properties.
        4,000원
        110.
        1998.09 KCI 등재 구독 인증기관 무료, 개인회원 유료
        경유자동차에 의한 오염물질의 배출은 주로 입자상물질과 NOx가 문제시되고 있는데 특히 입자상물질은 각종 호흡기질환의 원인 등으로 간주되어 이의 규제가 국내외적으로 강화되고 있다. 본 고에서는 이러한 입자상 물질을 제거하기 위하여 사용되는 각종 필터의 특성 및 제조방법에 대하여 알아보고자 하였다. 이를 위하여 먼저 경유자동차에서 발생하는 오염물질 및 이의 규제현황에 대하여 다루었으며 각종 후처리장치의 종류 및 개발현황에 대하여 언급하였다. 다음으로 가장 일반적으로 사용되어지는 필터인 세라믹 하니컴 필터를 중심으로 하여 원료 및 소재, 제조방법 그리고 열팽창계수의 조절 등에 대하여 논하였다.
        4,500원
        111.
        1998.09 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The fabrication process and properties of SiC particulate preforms with high volume fraction above 50% were investigated. The SiC particulate preforms were fabricated by vacuum-assisted extraction method after wet mixing of SiC particulates of 48 in diameter, as inorganic binder, cationic starch as organic binder and polyacrylamide as dispersant in distilled water. The SiC particulate preforms were consolidated by vacuum-assisted extraction, and were followed by drying and calcination. The drying processes were consisted with natural drying at for 36 hrs and forced drying at 10 for 12 hrs in order to prevent the micro-cracking of SiC particulates preform. The compressive strengths of SiC particulate preforms were dependent on the inorganic binder content, calcination temperature and calcination time. The compressive strength of SiC preform increased from 0.47 MPa to 1.79 MPa with increasing the inorganic binder content from 1% to 4% due to the increase of flocculant between the interfaces of SiC particulates. The compressive strength of SiC preform increased from 0.90 MPa to 3.21 MPa with increasing the calcination temperatures from 800 to 120 under identical calcination time of 4hrs. The compressive strength of SiC preform increased from 0.92 to 1.95 MPa with increasing the calcination time from 2 hrs to f hrs at calcination temperature of 110. The increase of compressive strength of SiC preform with increasing the calcination temperature and time is due to the formation of crystobalite phase at the interfaces of SiC particulates.
        4,000원
        113.
        1995.12 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        분말야금법으로 제조된 A6061기 입자분산강화 복합재의 열간압술가공에 있어서 압출특성에 미치는 강화입자의 종류, 빌렛특성 및 암술조건의 영향에 대하여 조사하였다. A6061기 복합재료의 열간 압술 전단 변형저항에 미치는 강화입자종류의 영향은 Si Cw > A12 O3f > A12 O3f > Si Cp의 순으로 되었으며, 모든 강화입자에서 부피분율이 증가함에 따라서 Kw값도 증가하였다. 압출조건, 강화입자의 첨가량 및 첨가입자의 평균입도에 관계없이 A12 O3p가 첨가된 복합재의 열간압출가공에 필요한 소요압력은 Si Cp의 경우보다 컸다. 압출압력은 압출 다이스 반각이 커질수록 감소하는 경향은 나타났다. 이것은 다이스 반각에 의해 생성되는 빌렛과의 접촉면적이 증가하여 전단마찰응력(m k3)이 상승하기 때문이다. 압출시 압출온도 상승은 저온에서 ~50˚C 정도 증가하였으며, 압출온도가 500˚C 이상이 되면 압출재 표면에 극심한 tearing이 발생하였다. 강화입자의 첨가량이 증가할수록 이 현상은 더 심하게 되었다.게 되었다.
        4,000원
        117.
        2023.02 KCI 등재 서비스 종료(열람 제한)
        Filter and microbalance sensitivity in measuring fine particulate matter mass is greatly influenced by particulate properties and environmental factors. Temperature and humidity control inside a measuring chamber with a microbalance, and neutralization of static charges on filters are essential for consistent filter weighing. Commercial weighing chambers are expensive with a unit price of tens of millions won. This study developed an inexpensive weighing chamber for weighing fine particulate matter and evaluatedits weighing performance. A microbalance with 1 μg precision was used to measure the weight of a filter. The microbalance was set in a transparent acrylic enclosure (100 x 60 x 65 cm3) equipped with temperature and humidity control equipments. Weighing performance of the chamber was examined using Teflon filters with or without different particulate sample types. Temperature and humidity were maintained at approximately 23.2±1.2 ℃ and 36.2±1.8℃ for 8 days, respectively.
        118.
        2022.12 KCI 등재 서비스 종료(열람 제한)
        This study investigated the effect of volcanic materials that erupted from the Nishinoshima volcano, Japan, 1,300 km southeast of the Busan area at the end of July 2020, on the fine particle concentration in the Busan area. Backward trajectory analysis from the HYSPLIT model showed that the air parcel from the Nishinoshima volcano turned clockwise along the edge of the North Pacific high pressure and reached the Busan area. From August 4 to August 5, 2020, the concentration of PM10 and PM2.5 in Busan started to increase rapidly from 1000 LST on August 4, and showed a high concentration for approximately 13 hours until 2400 LST. The PM2.5/PM10 ratio showed a relatively high value of 0.7 or more, and the SO2 concentration also showed a high value at the time when the PM10 and PM2.5 concentrations were relatively high. The SO4 2- concentration in PM2.5 in Busan showed a similar trend to the change in PM10 and PM2.5 concentrations. It rose sharply from 1300 LST on August 4, at the time where it was expected to have been affected by the Nishinoshima Volcano. This study has shown that the occurrence of high concentration fine particle in Busan in summer has the potential to affect Korea not only due to anthropogenic factors but also from natural causes such as volcanic eruptions in Japan.
        119.
        2020.06 KCI 등재 서비스 종료(열람 제한)
        This study analyzes the effect of negative air ions on the concentration of airborne particulate matter and evaluates the expected purification efficiency of open spaces for particulate matter by investigating the amount of negative air ions generated by plants. This study establishes a negative air ion generation treatment environment, plant environment, and control environment to measure the purification efficiency of particulate matter under the conditions of each, analyzing the expected purification efficiency by designing a particulate matter purification model. Results show that the amount of generated negative air ion according to environment was negative air ion generation treatment environment > plant environment > control environment; this order also applies to the particulate matter purification efficiency. Moreover, it took 65 min for the negative ion generation treatment environment, 90 min for the plant environment, and 240 min for the control environment to reach the standard expected purification efficiency of particulate matter concentration of 960 mg/m³ for PM10. For PM2.5, with the designated maximum concentration of 700 mg/m³, it took 60 min for the negative ion generation treatment environment, 80 min for the plant environment, and more than 240 min for the control environment. Based on these results, the expected purification efficiency compared to the control environment was quadrupled in the negative ion generation treatment environment and tripled in the plant environment on average.
        120.
        2020.05 KCI 등재 서비스 종료(열람 제한)
        To understand the composition, quantity, and quality of Suspended Particulate Organic Matter (SPOM) in the Gangneung Namdae Stream, Korea, we examined spatiotemporal variations in water temperature, salinity, chlorophlly a (Chl a), Particulate Organic Carbon (POC) and nitrogen (PON), and carbon stable isotope (δ13C) of SPOM at six stations in June (pre-monsoon), July (monsoon), and September (post-monsoon) 2017. With increasing precipitation, the average POC and C/N values increased significantly in July than in June. In September, the values decreased with decreasing precipitation. The δ13C values showed irregular spatiotemporal fluctuations among the stations and periods, thereby suggesting a greater contribution of autochthonous organic matter to the pool of SPOM than that of allochthonous organic matter derived from upstream. In addition, the large and irregular changes in POC, C/N ratio, C:Chl a, and δ13C compared to that of PON were observed for all periods among the stations, indicating a serial discontinuity of the stream. Our results suggest that the Gangneung Namdae Stream is significantly influenced by the increase in freshwater discharge caused by heavy rainfalls during the summer monsoon and post-monsoon periods.
        6 7 8