In this study, the formation, microstructure, and wear properties of Colmonoy 88 (Ni-17W-15Cr-3B-4Si wt.%) + Stellite 1 (Co-32Cr-17W wt.%) coating layers fabricated by high-velocity oxygen fuel (HVOF) spraying are investigated. Colmonoy 88 and Stellite 1 powders were mixed at a ratio of 1:0 and 5:5 vol.%. HVOF sprayed selffluxing composite coating layers were fabricated using the mixed powder feedstocks. The microstructures and wear properties of the composite coating layers are controlled via a high-frequency heat treatment. The two coating layers are composed of γ-Ni, Ni3B, W2B, and Cr23C6 phases. Co peaks are detected after the addition of Stellite 1 powder. Moreover, the WCrB2 hard phase is detected in all coating layers after the high-frequency heat treatment. Porosities were changed from 0.44% (Colmonoy 88) to 3.89% (Colmonoy 88 + ST#1) as the content of Stellite 1 powder increased. And porosity is denoted as 0.3% or less by inducing high-frequency heat treatment. The wear results confirm that the wear property significantly improves after the high-frequency heat treatment, because of the presence of wellcontrolled defects in the coating layers. The wear surfaces of the coated layers are observed and a wear mechanism for the Ni-based self-fluxing composite coating layers is proposed.
We make up meanings of three characters "shi"、"wen" and "di" by the help of the abroad meanings and the usages in ancient literature corpus. It’s a good way to explore the meanings of Chinese characters by the usage being corroborated in domestic literature and abroad corpus.
본 연구에서는 ALBC3 합금에 Ni기 자용성 합금으로 내마모성 및 내캐비테이션 특성을 향상시키기 위하여 용사코팅 후 열처리를 실시하여 캐비테이션 특성을 평가하였다. 본 연구 결과, 자용성 합금 코팅층이 높은 경도를 나타내어 내마모성이 우수할 것으로 판단되나, 다공질의 조직으로 인해 열악한 내캐비테이션 특성을 나타냈다. 따라서 열처리 조건의 최적화가 중요하며, 본 조건에서는 열처리온도를 높여 자용성 합금 내 B와 Si의 유동성을 증가시킴으로써 기공이나 결함을 제거하여 특성개선 효과를 기대할 수 있을 것으로 판단된다.
파장분할다중 광소자용으로 새로운 치환된 고분자인 폴리아릴렌에테르를 합성하였다. 이 물질은 열적으로 500˚C까지 안정하며, 1.5μm의 파장 근처에서 넓은 투과 영역을 가진다. 굴절률도 1.495-1.530의범위에서 불소 함유량으로 조절되었다. 단일 모드 광도파로를 제작하여 광도파손실을 측정하였다. 측정된 광도파손실은 1.55μm의 파장에서 0.2 dB/cm 이하였다.
AI2O3와 Na2O가 AFD법에 의해 제조된 sodium borosilicate 유리박막의 특성에 미치는 영향을 조사하였다. AI2O3함량이 증가함에 따라 66SiO2-27B2O3-7Na2O유리박막의 상분리는 억제되었으며, 6.0wt%의 AI2O3가 첨가되었을 때 공기중 급냉조건하에서 상분리가 없는 유리박막이 얻어졌다. AI2O3함량이 1.5에서 6.0wt%로 증가함에 따라 유리박막의 굴절율은 1.4610에서 1.4701로 선형적으로 증가하였으며, 복굴절률을 나타내는 TE 모드와 TM 모드의 차이도 점차적으로 증가하였다. 그러나 복굴절률은 유리박막을 전이온도 이하에서 재열처리함으로써 감소시킬 수 있었다. 66SiO2-27B2O3-7Na2O+6wt% AI2O3에 Na2O의 함량을 증가시켜 Na2O/B2O3가 0.23, 0.34, 0.45, 0.56인 유리박막을 제작하였다. Na2O/B2O3의 비가 증가함에 유리박막의 굴절율 및 복굴절률은 증가하는 경향이 있었다. 또한 Na2O/B2O3의 비가 증가함에 따라 유리박막의 상분리는 가속화되었다.
The purpose of this case study was to introduce a myoelectric hand prosthesis for upper extremity amputee and prosthetic training program. Limb loss can result from disease, injury, or congenital causes. Trauma has been increasingly important role as the cause of amputaion in young, vigorous, and otherwise healthy individuals. The higher the level of amputation the greater the functional loss of the part, and the more the amputee must depend on the prostheis for fuction and cosmesis. Myoelectrical control of prostheses is a recent development and has been steadily gaining in clinical use over the past 20 years. Such a prosthesis uses signals from muscle contraction within the stump to activate a battery driven moter that operates specific component fuctions of the prosthesis. This twenty years old male case was operated a right above-elbow amputation due to tracffic accident and admitted to Yonsei Rehabilitaion hospital for the preprosthetic and prosthetic training. The case was able to successfully complete his myoelectric hand prosthesis training in the February of 1995.