Recently, copper alloy netting has been proposed as a material for aquaculture facilities that can be set in harsh offshore environments. To design a cage made of copper alloy netting, it is necessary to calculate the flow of water through the netting and force of external sources on the netting. Therefore, this study measured and analyzed the current velocity reduction after passing through the netting and the hydrodynamic forces acting on the netting using copper alloy netting with nine solidity ratios. As a result of the reduction rate of the flow velocity through the netting, the flow reduction rate was increased as the solidity ratio of netting was increased. The flow reduction rate was also increased as the attack angle on the netting was decreased. In analyzing the resistance on the netting, we also discovered that resistance was increased with increase in the flow velocity and solidity ratio. An analysis of the hydrodynamic coefficient acting on the netting is shown that the drag coefficient tends to increase as the attack angle increases. We also analyzed the hydrodynamic coefficient according to the variation of the Reynolds number. When the drag coefficients acting on the netting were analyzed with the different Reynolds numbers, the Reynolds number increased from over 0.3 m/s to a relative constant. Finally, the copper alloy nettings had a smaller velocity reduction rate when comparing the flow velocity reduction rate between copper alloy nettings and nylon nettings.

The angle of attack of a cambered otter board in a bottom trawl was estimated using a three-dimensional semi-analytic treatment of a towing cable (warp) system that was applied to the field experiments of a bottom trawl obtained by the Scanmar system. The equilibrium condition of the horizontal component and vertical component of forces was used to the three forces acting on the otter board in the horizontal plane. Those forces were the force on the warp at the bracket, hydrodynamic lift and drag forces on the otter board and the force on the hand rope attached just behind the otter board. Also the equilibrium of moment about the front edge of the otter board was used to find out the angle of attack of the cambered otter board. When the warp length was 120m and 180m long and the towing speed was between 1.23 and 1.90 m/s, the estimated angle of attack of the cambered otter board was ranged between 26.1° and 29.6°, respectively, though the maximum lift force was at the angle of attack 22.6°. The angle of attack of the otter board was tended to increase weakly with the longer length of warp (180 m) at the same towing speed in the experiment.

How to extimate the angle of attack of a vertical V-type cambered otter board was described. A three-dimensional semi-analytic treatment of a towing cable system was applied to the field experiments of a midwater trawl obtained by the Scanmar system. Also the equilibrium condition of the horizontal component and vertical component of forces and moment around the otter board was used. When the warp length was 300m long and the towing speed was between 2.61 and 3.86 knots, the estimated angle of attack of the otter board was ranged between 24.7˚ and 26.2˚, though the maximum lift force was at the angle of attack 22˚.

본 논문에서는 펌프 노즐이 부착된 잠수 선형의 유동에 관해 수치해석 결과를 보여준다. 이는 속도분포, 양력계수, 영각의 값을 갖는 펌프젯 노즐이 선체와 부착되었을 때와 부착되지 않았을 때의 종강도 모멘트 등의 값들을 계산한다. 선형의 속도 분포에 따른 노즐의 영향면적과 양력계수(변호의 특성요인) 종강도 모멘트, 영각에 따른 도함수 등을 보여준다.

본 연구에서는 전개판의 영각 변화에 따른 정적안정성에 관하여 이론적 해석을 하였다. 또한 전개판의 형상별 유체력에 의한 정적 안정성을 평가하기 위하여 종횡비가 다른 평판과 만곡도가 다른 종만곡판을 사용하여 회류수조에서 유체력 및 모벤트를 측정하고 형상별 압력중섬계수와 모멘트 계수를 계산하였다. 본 연구에서 얻어진 결과를 요약하면 다음과 같다. 1. 전개판의 영각(α) 변화에 따른 끌줄의 장력과 후릿줄의 장력에 의한 모멘트 변화는 전개판을 항상 정적 안정성을 가지도록 작용한다. 2. 종횡비(λ)가 0.5, 1.0, 1.5인 평판의 압력중심계 수는 영각의 증가와 함께 전연에서 중심쪽으로 이동한다. 이것은 유체력에 의한 모멘트는 항상 정적으로 안정하도록 작용한다는 것을 의미한다. 3. 종횡비가 일정(λ=1.5)하고, 만곡도(CR)가 5%, 10%, 15%, 20%인 만곡판의 유체력에 의한 압력중심계수는 영각의 증가와 함께 후연에서 전연쪽으로 이동한 다음, 다시 만곡판의 중심쪽으로 이동한다 만곡판에 작용하는 유체력에 의한 모멘트는 만곡도가 커질수록 정적으로 불안정한 영각의 범위가 증가한다.

냉수관계일수가 엽신, 지경, 영곡의 무기성분조성에 미치는 영향을 조사분석하였던바 다음과 같은 결과를 얻었다. 1. 엽신, 지경, 영각의 무기성분조성은 냉수관계일수가 길어질수록 전질소함량은 증가하나 인산, 가리, 규산함량조은 낮았으며 숙기별로는 전질소와 인산은 출수기 가리는 엽신과 지경에서는 출수기, 영각은 성숙기, 규산은 성숙기에 많았고 지경의 무기성분함량은 엽신보다는 영각과 유사한 양식을 나타냈다. 2. 냉수에 의해 도체가 저질소흡수과정장해를 받으면 인산, 가리, 규산도 흡수장해를 받으며 그 경향은 지경보다는 엽신과 영각의 영양장해가 현저하였으며 도체에 전질소함량이 높고 규산함량이 낮으면 지경과 영화의 퇴화 및 불임이 증가되고 지경의 영양장해가 엽신과 영각보다 퇴화 및 불임에 밀접하게 관여하였다.