원자력 발전소에 지진격리장치를 설치하여 내진성능을 향상시킬 수 있다. 그러나 지진격리장치의 적용으로 지반과 구조물 사이에서 큰 상대 변위가 발생하게 된다. 따라서 지진격리된 구조물과 일반 구조물을 연결하는 연결배관시스템의 경우 지진리스크가 증가할 수 있다. 따라서 이러한 배관시스템의 지진취약도를 분석할 필요가 있다. 본 연구에서는 지진취약도 분석 을 위해 지진격리된 APR1400 원자력발전소와 주증기관을 대상으로 지진취약도를 분석하였다. 주증기관은 지진격리된 nuclear island의 보조 건물과 터빈 건물을 연결하는 인터페이스 배관이다. 지진취약도 분석을 위한 파괴모드는 누출관통균열로 정의하였다. 누출은 실험결과와 수치해석을 통해 손상지수로 정량화하여 취약도 분석을 위한 파괴기준으로 사용하였다. 파괴기준의 변동에 의한 취약도 곡선의 변동성을 확인하기 위하여 손상지수의 최솟값, 최댓값, 평균값 및 중앙값을 파괴기준으로 하여 지진취약도 곡선을 작성하였다.
본 논문에서는 모듈화(Module)된 부품을 활용한 탄성받침 성능개선기법에 대하여 소개하였다. 각각의 모듈화된 장치들이 지진 강도 및 이동 변위에 따른 단계별 거동을 함으로써 받침의 성능을 개선하게 된다. 모듈화된 장치들은 초기전단저항 블럭, 완충장치, 변위수용가이드, 낙교방지블럭이 있으며, 탄성받침에 추가적으로 적용되었다. 이 장치는 지진의 규모에 따라 4단계로 거동하며, 1차로 설계변위를 수용하고, 2차, 3차에서는 대규모 지진을 수용하며, 4차로는 대규모의 지진에 대해서 낙교방지가 가능하도록 설계되어 탄 성받침의 용량 제한을 증가시킨다. 본 논문에서는, 개발기술인 PRB 지진격리장치를 유한요소해석을 통해 해석하여 격리장치의 이론적인 거동이 구현되는지와, 대규모 지진에 해당하는 하중을 견딜 수 있는지 확인하였다. 그리고 이를 바탕으로 실험을 통해 성능평가를 진행하여 두 결과의 비교 분석을 통해 PRB 지진격리장치가 탄성받침의 성능을 개선할 수 있는지 검증하였다.
In a previous paper, ambient vibration tests were conducted on a cable stayed bridge with resilient-friction base isolation systems (R-FBI) to extract the dynamic characteristics of the bridge and compare the results with a seismic analysis model. In this paper, a nonlinear seismic analysis model was established for analysis of the bridge to compare the difference in seismic responses between nonlinear time history analysis and multi-mode spectral analysis methods in the seismic design phase of cable supported bridges. Through these studies, it was confirmed that the seismic design procedures of the “Korean Highway Bridge Design Code (Limit State Design) for Cable Supported Bridges” is not suitable for cable supported bridges installed with R-FBI. Therefore, to reflect the actual dynamic characteristics of the R-FBI installed on cable-supported bridges, an improved seismic design procedure is proposed that applies the seismic analysis method differently depending on the seismic isolation effect of the R-FBI for each seismic performance level.
In this study, a field bridge test was conducted to find the dynamic properties of cable supported bridges with resilient-friction base isolation systems (R-FBI). Various ambient vibration tests were performed to estimate dynamic properties of a test bridge using trucks in a non-transportation state before opening of the bridge and by ordinary traffic loadings about one year later after opening of the bridge. The dynamic properties found from the results of the tests were compared with an analysis model. From the result of the ambient vibration tests of the cable supported bridge with R-FBI, it was confirmed that the dynamic properties were sensitive to the stiffness of the R-FBI in the bridge, and the seismic analysis model of the test bridge using the effective stiffness of the R-FBI was insufficient for reflecting the dynamic behavior of the bridge. In the case of cable supported bridges, the seismic design must follow the “Korean Highway Bridge Design Code (Limit State Design) for Cable supported bridges.” Therefore, in order to reflect the actual behavior characteristics of the R-FBI installed on cable-supported bridges, an improved seismic design procedure should be proposed.
A hybrid mid-story seismic isolation system with a smart damper has been proposed to mitigate seismic responses of tall buildings. Based on previous research, a hybrid mid-story seismic isolation system can provide effective control performance for reduction of seismic responses of tall buildings. Structural design of the hybrid mid-story seismic isolation system is generally performed after completion of structural design of a building structure. This design concept is called as an iterative design which is a general design process for structures and control devices. In the iterative design process, optimal design solution for the structure and control system is changed at each design stage. To solve this problem, the integrated optimal design method for the hybrid mid-story seismic isolation system and building structure was proposed in this study. An existing building with mid-story isolation system, i.e. Shiodome Sumitomo Building, was selected as an example structure for more realistic study. The hybrid mid-story isolation system in this study was composed of MR (magnetorheological) dampers. The stiffnessess and damping coefficients of the example building, maximum capacity of MR damper, and stiffness of isolation bearing were simultaneously optimized. Multi-objective genetic optimization method was employed for the simultaneous optimization of the example structure and the mid-story seismic isolation system. The optimization results show that the simultaneous optimization method can provide better control performance than the passive mid-story isolation system with reduction of structural materials.
최근에는 다양한 중량의 구조물을 지진으로부터 보호하기 위해 지반으로부터 분리하는 면진장치로써 지반 격리용 받침이 활용된다. 지진의 피해를 저감시키는 설계방법 중에서 면진 설계는 구조물과 지반이 만나는 부분에 면진받침을 사용하는 방식으로 다른 내진/제진 설계 방법과 비교하면 가격대비 효율과 성능이 가장 우수하다. 본 연구에서는 지진 발생 이후 지속적으로 사용 가능한 새로운 개념의 자동복원 면진받침 시스템을 제안하고자 한다. 이러한 면진받침에 대한 성능을 검증하기 위하여 이론 적립 및 설계를 수행하고 실험체를 제작하여 실제 지진 데이터가 적용된 진동대 실험을 수행하였다. 기본특성실험, 면압의존성 실험, 속도의존성 실험, 변위의존성 실험에서 강도하중이 설계 목표치와 유사하였고, 거동 또한 설계값과 유사함을 확인하였고 이를 바탕으로 면진받침의 성능 검증을 분석하였다.
A base isolation system is widely used to reduce seismic responses of low-rise buildings. This system cannot be effectively applied to high-rise buildings because the initial stiffness of the high-rise building with the base isolation system maintains almost the same as the building without the base isolation system to set the yield shear force of the base isolation system larger than the design wind load. To solve this problem, the mid-story isolation system was proposed and applied to many buildings. The mid-story isolation system has two major objectives; first to reduce peak story drift and second to reduce peak drift of the isolation story. Usually, these two objectives are in conflict. In this study, a hybrid mid-story isolation system for a tall building is proposed. A MR (magnetorheological) damper was used to develop the hybrid mid-story isolation system. An existing building with mid-story isolation system, that is “Shiodome Sumitomo Building” a high rise building having a large atrium in the lower levels, was used for control performance evaluation of the hybrid mid-story isolation system. Fuzzy logic controller and genetic algorithm were used to develop the control algorithm for the hybrid mid-story isolation system. It can be seen from analytical results that the hybrid mid-story isolation system can provide better control performance than the ordinary mid-story isolation system and the design process developed in this study is useful for preliminary design of the hybrid mid-story isolation system for a tall building.
Various seismic isolation methods are being applied to bridges and buildings to improve their seismic performance. Most seismic isolation systems are the structural seismic isolation systems. In this study, the seismic performance of geotechnical seismic isolation system capable of isolating the lower foundation of the bridge structure from ground was evaluated. The geotechnical seismic isolation system was built with teflon, and the model structure was made by adopting the similitude law. The response acceleration for sinusoidal waves of various amplitudes and frequencies and seismic waves were analyzed by performing 1-G shaking table experiments. Fixed foundation, Sliding foundation, and Rocking foundation were evaluated. The results of this study indicated that the Teflon-type seismic foundation isolation system is effective in reducing the acceleration transmitted to the superstructure subject to large input ground motion. Response spectrum of the Rocking and Sliding foundation structures moves to the long period, while that of Fixed foundation moves to short period.
This study explored the risk assessment framework of multi-story piping system installed in critical facilities, in particular, seismically base-isolated building systems. In order to understand the seismic performance of multi-story piping system, OpenSees platform was used in this study. Also, Triple Friction Pendulum Bearing as a seismic base isolator was conducted in OpenSees. The focus of this study was on the development of seismic fragility or vulnerability of seismically isolated piping system.
A series of tests was conducted for full-scale single-pylon asymmetric cable-stayed bridges using a system of multiple shaking tables. The 2-span bridge length was 28 m, and the pylon height was 10.2 m. 4 different base conditions were considered: the fixed condition, RB (rubber bearings), LRB (lead rubber bearings), and HDRB (high damping rubber bearings). Based on investigation of the seismic response, the accelerations and displacements in the axial direction of the isolated bridge were increased compared to non-isolated case. However, the strain of the pylon was decreased, because the major mode of the structure was changed to translation for the axial direction due to the dynamic mass. The response of the cable bridge could differ from the desired response according to the locations and characteristics of the seismic isolator. Therefore, caution is required in the design and prediction in regard to the location and behavior of the seismic isolator.
This paper presents a detailed procedure for a nonlinear soil-structure interaction of a seismically isolated NPP(Nuclear Power Plant) structure using the boundary reaction method (BRM). The BRM offers a two-step method as follows: (1) the calculation of boundary reaction forces in the frequency domain on an interface of linear and nonlinear regions, (2) solving the wave radiation problem subjected to the boundary reaction forces in the time domain. For the purpose of calculating the boundary reaction forces at the base of the isolator, the KIESSI-3D program is employed in this study to solve soil-foundation interaction problem subjected to vertically incident seismic waves. Wave radiation analysis is also employed, in which the nonlinear structure and the linear soil region are modeled by finite elements and energy absorbing elements on the outer model boundary using a general purpose nonlinear FE program. In this study, the MIDAS/Civil program is employed for modeling the wave radiation problem. In order to absorb the outgoing elastic waves to the unbounded soil region, spring and viscous-damper elements are used at the outer FE boundary. The BRM technique utilizing KIESSI-3D and MIDAS/Civil programs is verified using a linear soil-structure analysis problem. Finally the method is applied to nonlinear seismic analysis of a base-isolated NPP structure. The results show that BRM can effectively be applied to nonlinear soil-structure interaction problems.
Base isolation is considered as a seismic protective system in the design of next generation Nuclear Power Plants (NPPs). If seismic isolation devices are installed in nuclear power plants then the safety under a seismic load of the power plant may be improved. However, with respect to some equipment, seismic risk may increase because displacement may become greater than before the installation of a seismic isolation device. Therefore, it is estimated to be necessary to select equipment in which the seismic risk increases due to an increase in the displacement by the installation of a seismic isolation device, and to perform research on the seismic performance of each piece of equipment. In this study, modified NRC-BNL benchmark models were used for seismic analysis. The numerical models include representations of isolation devices. In order to validate the numerical piping system model and to define the failure mode, a quasi-static loading test was conducted on the piping components before the analysis procedures. The fragility analysis was performed by using the results of the inelastic seismic response analysis. Inelastic seismic response analysis was carried out by using the shell finite element model of a piping system considering internal pressure. The implicit method was used for the direct integration time history analysis. In addition, the collapse load point was used for the failure mode for the fragility analysis.
Several researches have been studied to enhance the seismic performance of nuclear power plants (NPPs) by application of seismic isolation. If a seismic base isolation system is applied to NPPs, seismic performance of nuclear power plants should be reevaluated considering the soil-structure interaction effect. The seismic fragility analysis method has been used as a quantitative seismic safety evaluation method for the NPP structures and equipment. In this study, the seismic performance of an isolated NPP is evaluated by seismic fragility curves considering the soil-structure interaction effect. The designed seismic isolation is introduced to a containment building of Shin-Kori NPP which is KSNP (Korean Standard Nuclear Power Plant), to improve its seismic performance. The seismic analysis is performed considering the soil-structure interaction effect by using the linearized model of seismic isolation with SASSI (System for Analysis of Soil-Structure Interaction) program. Finally, the seismic fragility is evaluated based on soil-isolation-structure interaction analysis results.
본 논문에서는 비선형 지진격리교량의 최적 설계 방법을 제시하였다. 최적설계를 위한 목적함수로는 교각과 지진격리장치의 파괴확률을 고려하였으며, 상충하는 두 목적함수를 동시에 최적화하는 다수의 해를 효율적으로 검색하고자 유전자 알고리즘에 기반한 다목적 최적화기법을 도입하였다. 또한, 최적화 과정에서 요구되는 다수의 비선형 시간이력해석을 수행하지 않고도 교량의 확률적 응답을 효율적으로 예측할 수 있는 추계학적 선형화 방법을 접목하였다. 제시하는 방법의 효율성을 검증하기 위한 수치 예로서 실제 교량인 남한강교를 고려하였고, 제안하는 방법과 기존 비선형 시간이력해석을 이용한 생애주기비용 기반 설계법을 각각 적용하여 내진성능을 비교하였다. 내진성능을 비교한 결과, 제시하는 방법이 기존의 비용에 기반한 최적설계보다 우수한 성능 및 경제성을 보임을 검증하였다. 또한, 다양한 지진하중에 대해서도 제안된 방법이 보다 개선된 성능을 보임을 확인하였다.
기존의 교량받침으로 많이 사용되고 있는 폴리우레탄 디스크를 적용한 POT형식에 C형 강재감쇠장치를 추가적으로 적용한 새로운 형태의 지진격리장치에 대한 명확한 정적 성능검증과 동적특성을 파악하기 위하여 최대 극한 수직하중 시험, 최대 회전 시험, 동적재하 시험 및 동적재하 극한 반복시험을 시행하였다. 해석적 결과와 성능시험 결과를 비교분석한 결과, 충분한 감쇠능력을 보유하고있을 뿐만 아니라, 설계기준에도 적합하다는 결론을 얻을 수 있었다. 또한, EDC 및 유효강성값의 시험치가 이론치와 유사하여 시험 결과값의 분석이 유효함을 보였다.