본 연구에서는 콘크리트 구조물의 내구성 고도화를 위하여 고속도로용 교각 기둥부에 대하여 내부 식성이 우수한 GFRP 보강근 적용하였으며, 설계적 분석, 축소모형 시험체 제작 및 성능 시험을 통하 여 실용화의 타당성를 검증하였다. 설계적으로 교각의 기둥부는 축방향 주철근을 GFRP 보강근으로 대체하였다. 일반적으로 GFRP는 압축부에 취약한 것으로 알려져 있으며, 국외 기준의 경우는 압축부 에 대하여 GFRP 보강근은 저항력이 없는 것으로 가정하고 있다. 본 연구에서는 탄성 교각에 대하여 기존 철근을 대체할 수 있는 GFRP 보강근의 설계적 방안 제시 및 실물 시험을 통한 성능 검증을 수 행하여 결과를 제시하였다. 본 연구 결과는 고속도로용 탄성 교각 기둥의 내구성 증진을 위한 설계 및 실용화에 있어 가능한 가이드라인을 제시할 것으로 기대된다. 다만, 본 연구에서 다룬 기둥부는 주철 근만을 GFRP 보강근으로 대체한 것으로, 향후 GFRP 나선형 보강근 등의 적용, GFRP의 축하중 분담 률 및 건조수축 크리프 특성, 기둥부의 최소 보강근비 산정 그리고 GFRP 보강근의 압축강도 측정법 등 상세 사항에 대한 추가적인 연구가 필요할 것이다.

본 연구는 단조가력 하중을 받는 실물크기 비닐온실의 기둥-서까래-도리 접합부의 역학적거동을 알아보기 위해 현장에서 시공되고 있는 두 가지 형식의 실험체로 구조실험을 수행하였다. 실험결과를 바탕으로 두 가지 형식의 접합부에 대해서 휨성능을 분석하고 접합부 분류를 시도하였다. Type B 는 Type A에 비해 휨 성능이 77% 수준으로 나타났으며 두 형식 모두 강성 및 휨내력이 강접합 수준에 미치지 못하는 것으로 나타났다. 기둥-서까래-도리 접합부의 거동은 용접부 및 체 결구 변형에 의한 국부좌굴이 지배적이었다. AISC 기준에 의한 접합부 분류 결과, Type A와 B 접합부 모두 설계 시 가정하는 강접합 성능에 미치지 못하는 결과를 보였으며 단순 접합으로 분류되는 것으로 나타났다. 따라서 접합부 성능평가 및 분류 결과, 접합부 성능을 고려한 온실 설계가 이루어져야 하며 신뢰성 높은 온실 구조설계를 위해서 온실 접합부에 대한 명확한 설계기준 정립 연구가 필요할 것으로 판단된다.

내진설계기준이 개정됨에 따라 기 시공된 철근콘크리트 건축구조물의 내진보강에 대한 관심이 높아지고 있다. 특히 내진철근상세가 적용되지 않은 철근콘크리트 기둥의 경우 지진이 발생할 경우 취성적인 전단파괴가 발생할 가능성이 크다. 본 연구에서는 아라미드 FRP를 이용하여 비내진상세 철근콘크리트 기둥의 휨 및 전단내력 보강 후, 실험체를 반복횡하중 가력하여 아라미드 FRP의 내력 상승효과 및 연성능력의 증가를 확인하였다. 무보강 및 아라미드 FRP 보강 실험체를 비교 한 결과 아라 미드 FRP 보강이 비내진상세 철근콘크리트 기둥의 내력을 증가시키고 연성능력 또한 증가시킴을 확인하였다. 또한 비내진상세 철근콘크리트 기둥의 아라미드 FRP 보강 시 기둥 뿐만 아니라 접합부의 보강 또한 필요함을 확인하였다.

As buildings are becoming larger, demand for large-scale composite columns for heavy load is increasing. Welded built-up CFT column (ACT Column I) previously developed by authors of this study is structurally stable and economical. Characteristic of welded built-up CFT column is that there is a limitation of cross-sectional size and application of external diaphragm connection to ensure continuity of rib. Then, composite mega column (ACT Column II) was developed to improve limit of cross-sectional size. Composite mega column has a closed cross section like welded built-up CFT column, but thick plate is inserted between cold-formed steel to expand cross section size. However, when external diaphragm connection is applied to composite mega column, amount of steel is increased greatly and interference with finishing material occurs. In this study, internal diaphragm connection is applied through characteristic of composite mega column to which beam flange or stiffener can be attached to plate. In order to analyze this, simple tensile experiment of composite mega column connection with T-shaped stiffener was performed.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. T he experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. The experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. The experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

Bio sparging experiments were conducted in a laboratory column to investigate the potential removal of diesel contaminated groundwater. The objectives in this study were (a) to determine the extent of diesel degradation in laboratory columns under supplement of nutrient; (b) to determine the effect of variation of air flow in the removal of diesel and (c) to evaluate the potential enhancement of diesel degradation as a function of temperature. Our results showed that the nutrient supplement and higher air flow greatly enhanced diesel degradation. However, the variation of water temperature examined slightly increased degradation rate of diesel fuel.