ACT Column은 기존 CFT 기둥보다 얇은 강판으로도 동일한 구조적 성능을 발휘할 수 있으며, 콘크리트의 구속효과와 강관의 항복 후 좌굴응력의 향상을 기대할 수 있다. ACT Column은 보-기둥 접합부에 외다이아프램을 사용한 접합상세가 적용된다. 그러나 ACT Column 외부에 콘크리트가 피복되는 SRC 타입에서는 외다이아프램을 사용한 접합부의 적용이 난해하다. 그래서 ACT Column의 외부에 수직 스티프너와 수평 스티프너를 사용한 접합상세를 제안하였다. 본 논문에서는 제안상세를 대상으로 단순인장실험을 통해 성능검증을 수행하였다. 실험체는 현장에 사용량이 많은 크기의 ACT Column 으로 2개의 실험체를 제작하였다. 보 플랜지와 보 플랜지의 양측부에 부착된 윙플레이트를 통해 보 플랜지의 단면 내력이 링다이아프램으로 전달되는 명확한 응력전달매커니즘을 나타내었으며, 보 플랜지 전단면이 소성화되어 파괴되었다. 윙플레이트의 크기가 클수록 하중전달량이 증가하였으며, 제안한 접합상세의 강도평가식을 제시하였다.

Recently various composite beams in which concrete is filled in the U-shaped steel plate have been developed for saving story height and reducing construction period. Due to the high flexural stiffness and strength, they are widely being used for the building with large loads and long spans. The semi-slim AU composite beam has proven to take highly improved stability compared to the existing composite beams, because it consists of the closed steel section by attaching cap-type shear connectors to the upper side of U-shaped steel plate. In this study the finite element analyses were performed to evaluate the safety of the AU composite beam with unconsolidated concrete which were sustained through the closed steel section during the construction phase. The analyses were performed on the two types of cross section applied to the fabrication of AU composite beams, and the results were compared to the those of 2-point bending tests. In addition, the flexural performance according to the space of intermittent cap-type shear connectors and the location of reinforcing steel bars for compression was comparatively investigated. Through the results of analytical studies, it is preferable to adopt the yield moment of AU composite beam for evaluating the safety in the construction phase, and to limit the space of intermittent shear connectors to 400 mm or less for the construction load.

공작물 주차장은 제한된 높이를 갖는 시설물로써, 제한된 층고 내에 합리적 구조가 되도록 계획하는 것이 중요하다. 공작물 주차장은 제한된 층고 내에 주차 통로부(6m)와 주차공간부(5m)를 고려한 11m 전후의 장스팬이 대부분이다. 기존의 합성보는 제한된 층고내에서 충분한 보춤을 확보할 수 없기 때문에, 처짐과 같은 사용성에 대한 문제가 발생한다. 본 연구에서는 박스형 강재보의 상부플랜지를 콘크리트 슬래브의 마감면까지 노출시킨 형상의 합성보를 개발하였다. H형 합성보, U형 합성보, Box형 합성보를 대상으로 2점가력 휨실험을 수행하여, 구조특성을 비교하였다. 그리고 주차장 모듈에 대해 대안설계를 수행하여 경제성과 효율성을 비교평가하였다.

As buildings are becoming larger, demand for large-scale composite columns for heavy load is increasing. Welded built-up CFT column (ACT Column I) previously developed by authors of this study is structurally stable and economical. Characteristic of welded built-up CFT column is that there is a limitation of cross-sectional size and application of external diaphragm connection to ensure continuity of rib. Then, composite mega column (ACT Column II) was developed to improve limit of cross-sectional size. Composite mega column has a closed cross section like welded built-up CFT column, but thick plate is inserted between cold-formed steel to expand cross section size. However, when external diaphragm connection is applied to composite mega column, amount of steel is increased greatly and interference with finishing material occurs. In this study, internal diaphragm connection is applied through characteristic of composite mega column to which beam flange or stiffener can be attached to plate. In order to analyze this, simple tensile experiment of composite mega column connection with T-shaped stiffener was performed.

Unlike column-to-beam connections in reinforced concrete frames, column-to-beam connections are generally of the same type. Vertical load (D.L + L.L) and horizontal load (wind load, seismic load) are not the same in the upper and lower flange stress history. In the case of beams bonded to synthetic CFT columns, the tensile force is transmitted through the steel pipe column, and the compressive force is transmitted to the filled concrete, so the seismic performance is excellent even if the column has a relatively thin cross section. Also, in case of beam the composite CFT column, tensile force is taken by the steel pipe column, and the compressive force is caught by the inner concrete, and the shape of the column joint can be changed. In this study, the stress distribution of buildings is investigated according to the size and characteristics of the building, and the load history of the upper and lower flanges according to the building type is checked to show the structural possibility of the Asymmetric Diaphragms joint.

Recently, composite beams have been developed in which concrete is filled in a U-shaped steel plate for saving height of story. And due to high flexural stiffness and bending strength, it is widely applied in the field where high load and long span are required. The AU composite beam was improved the instability of the existing beams because it makes a closed section by attaching a cover type shear connection to the existing U - shaped composite beam with open upper section. In this study, AU composite beam resisted by composite-section during the using phase was evaluated the safety through the finite element analysis. The analysis is performed on the five specimens of AU composite beams according to applied deck-system and compared with the results of 2 - point bending test. As a result of the analysis, behavior of beam was shown by integrated composite section. And the evaluation of flexible capacity was p

As the ridges become larger and larger, a structural type that enables effective utilization of the long span and space is required. In the construction stage, the steel column supports the installation load. However, in order to secure the stability against the out - of - plane deformation of the steel column due to the lateral pressure when the concrete is laid, a binding frame is installed inside the steel pipe at constant intervals to resist the concrete installation pressure. When the concrete is cured and its performance as a composite section is exerted, a stress is generated which pushes the steel pipe out of the plane by the column compressive force. In this case, since the binding frame controls the deformation, the local buckling is delayed and the constraining effect on the concrete is increased. In order to evaluate the structural performance and behavior of the composite mega column according to the eccentricity effect and the effect of the binding frame, we carried out a structural test by fabricating eight monopole specimens with the binding frame reinforcement, reinforcing gap, reinforced cross section and eccentricity , And the experimental results are compared with the KBC2016 design formula.

The seismic design range for the national public facilities and power plant is expanded such as it becomes the earthquake Disaster Relief Act with the finance since 2008 as the seismic design concept is highly regarded, etc. The reinforcement of the brace is essential for the seismic performance security of the structure which is unable to be satisfied the current seismic design criteria. The tension brace in which the slenderness ratio is big was designed to the unique lateral force resistive element. And the buckling is generated in the first stage and it is unable to exhibit the structural capability. In this research, the buckling strength improvement the reinforcing method of the suggested tension brace tries to be verified through the experiment.

Rehabilitation of existing steel structure attached to a steel because cross-section is generally raising. But when the area of reinforcement increases, also increases the weight of steel can cause degradation of the operations. In addition, welding process cause discomfort which due to the interference of other process. To replace the existing method, there are researches and applications for civil steel structures on the outside. In this study, bond performance of FRP and Steel were tested to reinforce steel structures by using AFRP as well as CFRP.

The purpose of this study is to analyze flexural strengthening capacity of steel structures using composite materials through the experiment. Until now, A Flexural capacity reinforcing method of steel beams has been used by steel plate appending. The conventional method due to the increase in weight of the reinforcement reduces operation efficiency and welding process cause discomfort which due to the interference of other process. But, the specific gravity of AFRP(Aramid Fiber Reinforced Plastic) strip used as reinforcement in this study is less approximately 20% than steel(SS400) and tensile strength of AFRP is s higher approximately 4 times than steel(SS400). In overseas, CFRP(Carbon Fiber Reinforced Plastic) was used with civil steel structures but, it is difficult to find examples of applying AFRP. In this paper, A experiments were carried out as a variable(development length and thickness of AFRP and CFRP) for flexural strengthening of steel structures.

The object of this study is to develop a computer program that can help practical engineers to calculate sectional modulus and plastic moments of full composite girders with deck plates under positive and negative bending moments. The sectional modulus are equivalent moments of inertia for elastic analysis and plastic section modulus for plastic analysis. Results of Hwang's research are used to verify this developed program. AIK, KBC 2005 and 2009 are used to define effective widths of RC slab and to calculate positive plastic moments. For calculating negative plastic moments, this study proposed stress blocks and their equations. The developed program will be added about partial shear interactions and deflections of composite girders and finally proposed as GUI environment.

Through The Japanese case that they prevent earthquake damage by using seismic design, we design a building that before reform seismic design and conduct a seismic design evaluation. For detail evaluation, we use Nonlinear Static Analysis and find performance point that using by Capacity Spectrum Method of procedure B and Displacement Coefficient Method. We compared performance point of Capacity Spectrum Method of procedure B and target displacement of using Displacement Coefficient Method. Consequently we obtain a result that those are similar. Result of understanding each element performance level that base on performance point, some elements are unsatisfactory. Thus, We have come to conclusion that re-evaluate after reinforce structure.

The composite beam is efficient and easy to construction. But shear connector is needed for the composite action. This research developed SPC beam in order to reduce the shear connector with utilization of mechanical bonded force by the cross sectional shape. The flexural behavior of SPC beam was evaluated through two point loading test.