MCCI, one of the ex-vessel phenomena during a severe accident, is generally caused by mutual reactions between molten core and reactor building basemat concrete, but occurs between sacrificial materials made by concrete and corium in APR nuclear power plant with PECS applied. In this paper, MCCI analysis was performed to design and apply a device to block the core melt at the junction connected to the ICI cavity sump from the core catcher installed in the reactor cavity of the APR. Unlike the sacrificial material, which has a cooling effect by inducing erosion of the ex-vessel core melt, the device is composed of concrete applied as a barrier to protect the ICI cavity sump. The decent thickness of the barrier wall of the device was calculated.

The concrete structure of a nuclear power plant is a major safety structure that performs shielding functions to block radioactive materials and radiation, heat removal, and isolation functions. Therefore, concrete structures of nuclear power plants must prove structural safety from immediately after construction to dismantling, and a representative method for this is to investigate compressive strength. The compressive strength and specimen standards of concrete structures are specified in ASTM C 42/C 42M, and samples must be obtained through core drilling in order to collect samples according to this standard. However, commercial equipment requires anchor installation work causes radiation dust generation. Even commercial products have developed equipment that does not require anchor installation work, but it can only be applied to flat walls and cannot be applied to curved walls such as bioshields. To solve this problem, a method of fixing to the scaffolding pipe was designed. The equipment developed based on this method fundamentally blocks the generation of radioactive dust. The vertical position can be adjusted using guide shafts and jack screws, and the horizontal position can be adjusted using scaffolding clamps. In addition, the distance between the installation location and the wall can be adjusted by adjusting the scaffolding clamp location of the device. Lastly, it can be rotated to the left and right, so that even on a curved wall, the sampling position can be performed perpendicular to the wall. Core drills that take specimens for measuring compressive strength use the wet type. Core drilling by wet type in radioactively contaminated concrete leads to the disposal of sludge as radioactive waste. Water supplied during core drilling is scattered in all directions by the rotation of the core drill bit, which causes radiation exposure to workers, so measures must be taken to ensure that the water does not splash and gather in one place. Nileplant Co., Ltd. has developed a sludge collection device that can be used with a core drilling device. It can be inserted into a 4-inch core drill bit to meet the specimen regulations of ASTM C 42/C 42M, and nylon resin was used as a material to withstand friction with water, and the wall of the drainage part was thickened to increase durability. Based on these results, it is expected to be able to work more quickly and safely when collecting core drilling samples of radioactively contaminated concrete or radiation and concrete.

본 연구에서는 양생물주기 및 보양을 하지 않은 구조체의 압축강도와 표준 양생 공시체의 압축강도를 비교 평가하였 다. 코어채취를 위해서 980x2090x200mm3 철근콘크리트 슬래브를 준비하였으며, 콘크리트 공시체 25개를 KS F 2405에 따라서 표준 양생, 20개를 구조체와 동일한 환경에서 대기중 양생을 하였다. 실험 결과, 28일 표준공시체 압축강도 대비 코어 채취 압 축강도는 약 4MPa 낮게, 대기중 양생 공시체의 압축강도는 약 7.6MPa 낮게 측정되었다. KCS에서는 양생기간의 온도가 낮을 경 우 온도보정강도를 제시하고 있으며, 실험결과로부터 제시된 값이 적정함을 확인하였다. 7일, 14일에 측정된 대기중 공시체의 압축강도는 코어채취 공시체의 압축강도와 유사하였지만, 28일 압축강도는 현저하게 차이가 나타났다. 초기 구조체의 초기 압축 강도 예측에 대기양생 공시체를 이용하는 것은 가능하지만, 28일 압축강도를 추측하는데 대기중 양생 공시체를 사용하는 것은 무리가 있다고 판단된다.

본 논문에서는 유전알고리즘을 사용하여 철근콘크리트 구조물의 최적 지진설계를 효율적으로 수행하기 위해 클러스터를 사용하는 경우 확장성을 확인하였다. 클러스터를 구성하는 코어프로세서의 개수를 증가시키면서 유전알고리즘의 각 세대에 소요되는 시간의 감소를 관찰하였다. 단일 퍼스널 컴퓨터의 구성을 분류한 후, wall-clock time과 암달의 법칙으로 예상된 값을 비교하여 예상되었던 병목현상을 확인하였다. 이에 클러스터의 확장성에서 복합적인 요인에 의한 경향을 확인할 수 있었다. 병목현상의 물리적인 요인과 알고리즘 측면에서의 요인을 구분하기 위해 유전알고리즘의 개채수를 나누어 실험을 수행하여 결과를 확인하였다.

이 연구는 압출성형으로 생산되고 있는 프리스트레스트 콘크리트 중공 슬래브(HCS)의 휨 성능을 평가하고자 단면의 높이를 변수로 휨 실험을 수행하였다. HCS는 단면의 높이에 따라 총 2체를 제작하였으며, 1,000kN의 액추에이터를 이용하여 4점 가력을 실시하였다. 실험결과, HCS의 휨강도는 예측결과에 대한 실험결과의 비가 평균 1.01 ∼ 1.04를 나타내어 현행 설 계기준에서 요구되는 구조성능을 만족하는 것으로 나타났다.

The core is extracted to evaluate the concrete compressive strength of the actual structure. However, the core strength can vary in the core size due to two reasons - size effect in fracture mechanics and effect of coring damage. Therefore, the purpose of this study was to assess quantitatively the difference in strength due to these effects. The core damage tended to increase relatively as the core section was smaller. The strength difference due to the size effect in fracture mechanics did not show any significant difference according to the curing condition and was measured to be similar to the previous study.

The purpose of this study is to compare the ultrasonic pulse velocity before and after core compression test of steel fiber reinforced concrete using the ultrasonic pulse velocity method. The correlation between the column member ultrasonic pulse velocity before core test, the column member ultrasonic pulse velocity after core test, and the compressive strength of the core specimen were analyzed by fabricating a steel fiber reinforced concrete hollow column member.

In this study the cyclic lateral loading tests were performed on the hybrid precast concrete panels that are interconnected by dry joints to emulate concrete shear wall cores for a mid-rise modular building. Test results show that it is necessary to improve the details of vertical reinforcement welded to the flange of C section member to increase the lateral resistance of hybrid precast concrete panels.

For the purpose of evaluating the strength of high-strength concrete, the strength of small diameter core was compared with 100, 50, and 30 mm cores. In case of high strength concrete, the smaller the core diameter, the lower the strength was. It is probably due to the disturbance of specimen during coring. Therefore, it is considered that it is difficult to apply in the field.

Recently, Earthquake occurrence in korea has become frequent, and the seismic safety of low-rise piloti buildings becomes more and more important. In this study, the differences in seismic performance between before and after reinforced by concrete filled steel tube (CFT) of low-rise central core type piloti building structures were compared.

Recently, Earthquake occurrence in korea has become frequent, and the seismic safety of low-rise piloti buildings becomes more and more important. In this study, the seismic retrofit method of low-rise eccentric core type piloti building structures using concrete filled steel tube (CFT) columns was analysed and verified for seismic performance.

Recently, Earthquake occurrence in korea has become frequent, and the seismic safety of low-rise piloti buildings becomes more and more important. In this study, the differences in seismic performance between before and after reinforced by concrete filled steel tube (CFT) of low-rise central core type piloti building structures were compared.

Recently, Earthquake occurrence in korea has become frequent, and the seismic safety of low-rise piloti buildings becomes more and more important. In this study, the seismic retrofit method of low-rise eccentric core type piloti building structures using concrete filled steel tube (CFT) columns was analysed and verified for seismic performance.

To improve the wet process of concrete core wall, which is one of lateral load resisting system in high-rise modular building, the new composite panel system is developed and its structural performance under lateral load is investigated analytically.

콘크리트의 강도를 평가하기 위하여 반발경도법과 초음파속도법이 폭넓게 사용되고 있다. 그러나 재료의 상태뿐만 아니라 콘크리 트의 재령, 성숙도 및 손상도 등에 따라 예측강도와 현장의 실제강도가 차이가 발생하게 된다. 표준공시체와 현장에서 드릴링에 의하여 채취하 는 코어공시체의 압축강도는 드릴링하는 동안 기계에 의한 교란이 발생하여 압축강도에 영향을 미치게 된다. 또한 반발경도 및 초음파속도의 경우에도 콘크리트의 재령 및 성숙도가 변화함에 따라 표면의 경도와 내부 미세조직의 변화에 의해서도 변화하게 된다. 저자들은 재령와 코어 의 영향을 비파과시험결과에 반영하기 위하여 실험을 실시하였으며, 코어 및 콘크리트 재령에 의한 영향을 압축강도 실험 및 예측결과와 비교 분석하였다.