In this paper, an experimental study was carried out for vibration control of cable bridges with structurally flexible characteristics. For the experiment on vibration control, a model bridge was constructed by reducing the Seohae Grand Bridge and the shear type MR damper was designed using the wind load response measured at Seohae Grand Bridge. The shear type MR damper was installed in the vertical direction at the middle span of the model bridge, and dynamic modeling was performed using the power model. The tests of the vibration control were carried out by non-control, passive on/off control and Lyapunov control method on model bridge with scaled wind load response. The performance of the vibration control was evaluated by calculating absolute maximum displacement, RMS displacement, absolute maximum acceleration, RMS acceleration, and size of applied power using the response (displacement, acceleration, etc.) from the model bridge. As a result, the power model was effective in simulating the nonlinear behavior of the MR damper, and the Lyapunov control method using the MR damper was able to control the vibration of the structure and reduce the size of the power supply.

In the case where a MR-damper is employed for vibration control, it is important to decide on how much control capacity should be assigned to it against structural capacities (strength and load, etc). This paper aims to present a MR-damper's control capacity suitable for the capacities of the structure which needs to be controlled. First, a two span bridge was built equipped with a MR-damper, which constitutes a two-span MR-damper control system. Then, inflicting an earthquake load on the system, a basic experiment was performed for vibration control, and a simulation was also carried out reflecting specific control conditions such as MR-damper and rubber bearing. The comparison of the results against each other proved their validity. Then, in order to calculate an optimal control capacity of the MR-damper, structural capacity was divided into eleven cases in total and simulated. For each case, an additional load of 30 KN was inflicted everytime, thereby increasingly strengthening structural capacity. As a result of the study, it was found that the control capacity of MR-damper of 30 KN was safely secured only with lumped mass of more than 150 KN(case 6). Therefore, it is concluded the MR-damper showed the best performance of control when it exerted its capacity at around 20% of structural capacity.

This paper is concerned with an experimental research to control of random vibration caused by external loads specially in cable-stayed bridges which tend to be structurally flexible. For the vibration control, we produced a model structure modelled on Seohae Grand Bridge, and we designed a shear type MR damper. On the center of its middle span, we placed a shear type MR damper which was to control its vibration and also acquire its structural responses such as displacement and acceleration at the same site. The experiments concerning controlling vibration were performed according to a variety of theories including un-control, passive on/off control, and clipped-optimal control. Its control performance was evaluated in terms of the absolute maximum displacements, RMS displacements, the absolute maximum accelerations, RMS accelerations, and the total power required to control the bridge which differ from each different experiment method. Among all the methods applied in this paper, clipped-optimal control method turned out to be the most effective to reduces of displacements, accelerations, and external power. Finally, It is proven that the clipped-optimal control method was effective and useful in the vibration control employing a semi-active devices such MR damper.

In recently, sky-bridge are often applied to high-rised adjacent buildings for pedestrian bridge. the seisnic response control of adjacent buildings have been studied and magneto-rheological(MR) fluid dampers have been applied to seismic response control. In this study, vibration control effect of the MR damper connected adjacent buildings has been investigated. Adjacent building structures with different natural frequencies were used as example structures. Two typed of control methods, displacement based or velocity based, are applied to determinate control force of MR damper. In this numerical analysis, it has been shown that displacement-based control algorithm is more effective than velocity-based control algorithm for seismic response control of adjacent buildings. And, when displacement-based control method is applied to control of adjacent buildings, the control of building occurred large displacement is more efficient in reducing the seismic response.

현재 건축 및 토목 구조물의 진동제어에 있어서 준능동제어에 대한 연구가 많이 수행되고 있으며 준능동제어 시스템은 수동제어와 능동제어의 장점을 가지고 있다. 최근 적은 전기 에너지로 제어가 가능한 MR 감쇠기가 개발되어 준능동제어 분야에 적용되고 있으며 이러한 MR 감쇠기를 스마트 감쇠기라 불리고 있다. 본 논문에서는 실시간으로 제어가 가능한 MR 감쇠기를 인접한 두 건축물 사이에 설치하여 제어성능을 알아보고자 한다. 또한, groundhook과 skyhook 제어 알고리즘을 결합한 복합제어 모델을 인접한 건축물의 진동제어에 적용하여 복합제어 모델의 제어성능을 알아보고자 한다. 복합제어 모델을 적용하여 인접한 두 건축물의 진동제어 성능을 분석한 결과, 복합제어 모델이 인접한 두 건축물의 진동제어에 매우 효과적인 것을 알 수 있었다.

Real-time hybrid testing technique (RT-HYTT) is a structural dynamic testing method that the numerical calculation of the equations of motion of a structure and the experimental measurement of the reaction forces resulting from the application of this motion to the numerical structure are simultaneously implemented in real time. In this paper, structural control performance of the magneto-rheological (MR) damper installed in a real-scaled 5 story building is experimentally evaluated through real-time hybrid test method. In this method, a numerical substructure is based on a structural model identified from the forced vibration testing results of a real-story building, and an MR damper that is used as an experimental substructure is physically tested with a universal testing machine (UTM). In the test, load cell on the UTM measure the force necessary to attain the required story displacement and these structural reaction forces are returned to the computer for use in next time step calculation of a numerical structural model. Test results show that the higher level of control force generated by the Mr damper causes the lower level of controlled response of a structure.

본 연구에서는, 지진하중에 의해 구조물에 발생하는 진동을 제어하기 위하여 토글 시스템의 비선형성을 연구하고, 자기유변유체(MR) 감쇠기를 장착한 토글 가새시스템의 성능을 평가하였다. Bingham 모델로 표현되는 MR감쇠기의 제어력이 속도의 함수인 점을 고려하여, 토글 가새시스템에 의한 속도증폭계수를 계산하였고 토글 형태에 대한 증폭계수효과를 평가하였다. 특히 강한 지진하중에서 쉐브론과 대각가새 등의 전형적인 가새시스템에 장착된 MR감쇠기가 충분한 응답감소효과를 제공하지 못하는 경우에, 토글 가새시스템을 사용하여 제어성능을 크게 강화시키는 것을 수치해석 결과를 통하여 확인하였다.

이 논문에서는 소형 다층 구조물의 진동제어에 적용하기 위한 복합모드의 자기유변유체(MR) 감쇠기를 개발하였다. 우선, 도식적으로 전단, 유동, 복합모드 MR감쇠기의 형태를 설계조건과 함께 표현하였고, 각각의 모드에 대하여 자기장에 따른 감쇠력을 예측하기 위한 해석모델을 유도하였다. 다음으로 적당한 크기의 복합모드 MR감쇠기를 제작하고 자기장에 따른 감쇠특성을 시간영역에서 평가하였다. 마지막으로 지진하중을 받는 소형구조물에 제작된 MR감쇠기가 준능동 제어기로 제어하였을 때의 성능을 수치적으로 평가하였다.

수동동조질량감쇠기의 진동제어 효과는 질량감쇠기와 구조물과의 동조로 인하여 나타나고 있다. 그러나 바닥판 구조물의 질량과 강성의 변화로 인하여 실제 구조물에 있어서 비동조 현상이 일어나기도 한다. 이러한 상황에서는 수동동조질량감쇠기의 성능이 비효율적이며 경우에 따라서는 구조물의 진동을 증가시키기도 한다. 본 논문에서는 기계나 사람에 의한 바닥판 구조물의 진동을 줄이기 위하여 자기유체감쇠기의 적용성을 알아보고자 한다. 준 능동제어와 groundhook 제어 알고리즘을 적용하여 준능동감쇠기의 성능과 수동질량감쇠기의 성능을 비교 분석하였다. 또한 비동조 상황에서의 준능동감쇠가와 수동질량감쇠기의 견인성을 비교 분석하여 다음과 같은 결론을 얻었다. 자기유체감쇠기는 동조상황에서 우수한 제어 성능을 가지고 있으며 비동조 상황에서도 우수한 견인성을 보여주고 있다.

본 논문의 목적은 구조물의 지진응답제어를 위해 사용되는 MR 감쇠기의 성능을 선형화기법을 이용하여 등가의 선형 점성으로 표현하고, 이를 MR감쇠기가 설치된 축소건물에 대한 시스템식별 실험을 통해 얻은 결과와 비교하여, MR 감쇠기의 성능평가에 대한 선형화 기법의 타당성을 검증하는 것이다. 먼저, MR 감쇠기의 이력모델로 많이 사용되는 모델 중, 수학적 표현이 간단한 Bingham 모델에 등가선형화 기법을 적용하여 등가의 점성을 구하였다. 그리고, 진동대 가진실험을 통해 얻어진 MR감쇠기가 설치된 3층 소형구조물의 전달함수로부터 모드정보를 추출하고 이를 사용하여 구조물의 점성행렬을 구하였다. 선형화기법을 통해 Bingham 모델을 사용하여 예측된 점성과 실험을 통해 얻어진 MR감쇠기에 의해 증가된 점성은 5% 오차범위 이내로 일치된 결과를 보여준다.

본 연구에서는 위의 어려움을 해결하기 위해, 스마트 수동제어 시스템을 제안하였다. 스마트 수동제어 시스템은 MR댐퍼와 EMI시스템으로 구성되며, EMI시스템은 영구자석과 솔레노이드 코일로 이루어진다. EMI시스템은 MR댐퍼의 왕복운동에너지를 전기에너지로 변환하므로, 스마트 수동제어 시스템은 외부 전원 없이 외부하중에 따라 댐퍼의 점성을 바꾸는 적응성을 갖는다. 따라서 간단하고 효율적인 장치로써, 대형토목구조물에 적용 가능하다. 이의 확인을 위해 예제를 통한 수치해석을 수행하였으며, 스마트 수동제어 시스템이 강진에 대해서는 기존의 반능동 제어 MR댐퍼 시스템 보다 우수한 성능을 보인다.

In this paper, various dynamic model of magnetorheological (MR) damper, is required for describing the hysteresis of MR damper and for their application are investigated to structural control. The dynamic characteristics and control effects of the modeling methods for MR dampers such as Bingham, biviscous, hysteretic biviscous, simple Bouc-Wen, Bouc-Wen with mass element, and phenomenological models are studied. Of these models, hysteretic biviscous model which is simple and describes the hysteretic characteristics, is chosen for numerical studies. The capacity of MR damper is determined as a portion of not the building weight but the lateral restoring force.

The purpose of this paper is to evaluate the performance of a MR fluid damper for seismic vibration control of a structure in terms of equivalent linear damping or stiffness based on linearization technique and to experimentally verify the results from linearization technique by comparing them to those from system identification of a building structure with MR damper. First, among the various models for MR damper, the equivalent stiffness and damping are estimated for Bingham model which is mathematically simple and for Bouc-Wen model which can describe any kind of hysteretic behavior. Second, transfer function of a building structure with MR damper is obtained by performing shaking table tests and the stiffness and damping matrices of the structure are constructed using the modal information obtained by the transfer function. It is observed that the damping mathematically estimated using linearization technique for Bingham model matches well with the damping coefficient experimentally obtained by system identification.

본 논문에서는 미국토목학회(ASCE)의 사장교에 대한 첫번째 벤치마크 문제를 이용하여 제어-구조물 상호작용을 고려한 새로운 반능동제어 기법을 제안하였다. 이 벤치마크 문제에서는 2003년 완공 예정으로 미국 Missouri주에 건설 중인 Cape Girardeau 교를 대상 구조물로 고려하였다. Cape Girardeau 교는 New Madrid 지진구역에 위치하고, Mississippi 강을 횡단하는 주요 교량이라는 점 때문에 설계단계에서부터 내진 문제를 중요하게 고려하였다. 본 연구에서는 MR 유체 감쇠기를 제어 장치로 제안하였고, clipped-optimal 알고리듬을 제어 알고리듬으로 사용하였다. 또한, 대용량 MR 유체 감쇠기 실험 결과를 이용하여, Bingham 모델, Bouc-Wen 모델, 수정된 Bouc-HWen 모델과 같이 수치해석에 이용할 수 있는 다양한 동적 모델을 개발하였다. MR 유체 감쇠기는 제어가능한 에너지 소산장치이며 구조물에 에너지를 가하지 않기 때문에 제안된 제어기법은 한정입출력 안정성이 보장된다. 수치해석을 통해, MR 유체 감쇠기를 이용한 반능동제어 기법이 사장교의 응답 감소에 효과적인 방법임을 증명하였다

This research is an experimental study attempting to use MR-dampers to control the complex behavior of multi-span bridge structures due to external loads such as seismic loads. For the purposes of this study, the model of components in each structure is identified, and then based on the results, a simplified system of the structure is derived. The performance of MR-dampers for complex behavior control is evaluated separately, according to the self-performance of MR-dampers and according to the performance based on applications of control algorithms. Based on the simplified system, Lyapunov control algorithm and Clipped-optimal control algorithm are applied. As a result, MR-damper is proven to be effective in the complex behavior control of multi-span bridge structures.

This study attempted to assess performances of adopted MR-damper to control the complex behavior caused by the interaction of independent continuous structures. For this, MR-damper (30kN) was designed and fabricated, and the MR-damper model was investigated using the Nonlinear Bingham Plastic Damper (NBPD). To assess experimental performances, a control test on the model structure was performed while El-centro 150% of seismic load was being applied. Then, MR-damper was placed between two independent structures to have it control independent displacement and complex behavior between the two structures. This study found that MR-damper is effective in controlling complex behavior of structures.

본 연구에서는 준능동 진동 제어를 위한 MR 감쇠기의 동적 모델링을 통한 특성을 분석 및 평가하였다. 실제 구조물 크기의 모형구조물을 진동제어하기 위하여 Semi-active 성능의 MR Damper를 설계/제작 하였다. 일반적으로 MR Damper를 이용한 준능동 제어 시스템을 구축하기 위해서는 감쇠장치의 발생 감쇠력 및 거동 성향 등의 데이터를 수치적으로 나타낼 수 있는 동적 모델이 요구된다. 따라서 본 연구에서는 MR Damper의 동적거동을 예측/평가 할 수 있는 모델링을 하기 위하여 다양한 동적 모델 중Power 모델 및 Bingham 모델을 적용하였다. 이때 동적 모델과 비교/평가하기 위하여 개발된 MR Damper의 동하중 실험을 수행하였다. 동하중 실험조건은 가진 주파수를(0.15Hz, 1.0Hz, 2.0Hz) 선정하고, 주파수별 각각 3가지씩 가진 속도를 달리하여, 변위가 감쇠력에 미치는 영향력을 확인하였다. 이렇게 얻어진 MR Damper의 동하중실험 결과를 적용하여 각 동적 모델 별 모델변수를 규명하였고, 이를 바탕으로 힘-속도 관계곡선 및 예측된 발생 감쇠력을 산출하였으며, 산출된 결과와 개발된 MR Damper의 실험 결과를 상호 비교⋅평가하였다. 최종적으로 본 연구에서 개발한 MR Damper는 준능동 제어장치로 활용 가능함을 확인 하였고, 다양한 변위를 이용한 실험을 통하여 정상적인 진동제어를 위해서는 최소 2mm 이상의 변위가 확보되어야 한다는 결과를 얻었다.

This paper aims to prove the effectiveness of MR damper as a smart control device when controlling the earthquake invoked transverse vibration of a two-span simple bridge. Applying a 40% of Kobe earthquake and a 120% of El-centro on a target structure, experiments were performed under two conditions: passive on (current on) and Lyapunov control algorithm embedded. MR damper's control performance was analyzed and contrasted under each different condition. It was concluded that MR damper was effective in controlling the vibration of the bridge.

In this dissertation, experimental study about the real-time vibration control of the bridge structure was conducted by using the semi-active vibration control method that has been in the spotlight recently. Based on the laboratory-scale bridge model in the form of the cable-stayed bridge, the shear type MR damper and the semi-active vibration control algorithm (Lyapunov and Clipped-optimal) were applied in order to the control the harmful vibration in real time. From the investigation of the test results, the performance of each semi-active control algorithm was evaluated quantitatively.

In this research, our team developed a semi-active MR damper by designing and producing it, and also evaluated its performance for the control of large structure. It is specially designed to have a flexible capacity to control a range of 10KN-30KN with an input current of 0 - 3A. The evaluation of its performance was carried out; first, to input a 0 - 3A electric current at various frequence range between 0.15Hz and 2Hz, then to measure a consequent power and displacement. By finding that the MR damper secures a control capacity of 10KN-30KN, it was proved that the MR damper is capable to control any large structure.