In this study, experiments were performed using a model of a very large crude oil carrier (VLCC), which is a typical blunt ship, in a wave-making towing tank. The aim of the experiments was to determine the effect of added resistance in waves on the various operating conditions of a VLCC. An analysis of the results was conducted to determine the characteristics of resistance performance in waves. In addition, the characteristics of added resistance on a tanker were analyzed under irregular waves based upon the above result. The experimental results showed that added resistance was the highest around λ/L = 1.0, and the added resistance increased with the increase of the ship speed. Furthermore, under even keel conditions, the added resistance was higher than that under the trim changes, and the smallest added resistance was measured at the trim by the stern. Based on the experimental results, this study proposes effective operating conditions by analyzing the characteristics of the mean added resistance and the expected extreme response in irregular waves.

In the present study, numerical analysis algorithm for the hull form optimization was taken into account using optimization algorithm. In this algorithm the sequential quadratic programming method was applied as an optimizer and the potential-based panel method was adopted to get the wave resistance coefficient as the objective function. The hull form was modified using the B-spline surface modeling technique during the whole optimization process. The developed numerical analysis algorithm was applied to the 300K VLCC and the optimized ship were compared with the original ship.

In this paper a study on prediction of the wave resistance performance of a very large crude oil carrier(300K VLCC) was taken into account according to the changes in L/B/T. The wave resistance of the ship was calculated using the potential based panel method in which exact nonlinear free surface boundary conditions and the trim and sinkage were considered. The panel cutting method were implemented to generate the hull surface panel and the free surface panel were generated using the variable free surface method. The numerical analysis was carried out according to the 12 different ships. The wave resistance coefficients and the wave patterns of the 12 different ships were compared with each other. As a result the wave resistance of a ship was found to be significantly affected in L/B than T.

In the present study, numerical algorithms for a very large crude oil carrier(300K VLCC) were taken into account. The potential flow analysis method was adopted to predict the flow pattern and the fluid force around a ship. The exact nonlinear free surface boundary condition were compared to predict the wave system generated by the ship and the trim and sinkage state of the ship also were considered. In order to deal with complex geometries of the 300K VLCC the panel cutting method was adopted to generate the ship surface panel and the variable free surface panel method was taken applied to generate the free surface panel. The developed numerical analysis algorithm were applied to the 300K VLCC and the results predicted by the numerical analysis were compared with the experimental data

It is well known that simulation study in the preliminary design stage of harbors or berths is of great use, since it can provide helpful informations to the designer from the view point of ship navigations. In this paper, a brief review is made in the safety assessment of ship navigation for a 320,000 DWT VLCC entering Yecocheon harbor area, which is carried out by shiphandling simulator system. The geographic data base for the harbor as well as the mathematical models of the ship and environmental effects are designed and developed. Based in the on-site inspections and interviews with pilots in Yeocheon area, basic maneuvering plans and consistence with real operation conditions. Berthing and deberthing maneuvering simulations as well as approaching and departing simulations are carried out by 3 experienced navigators according to the maneuvering plans and environmental scenarios. The simulation results are analysed in various ways to evaluate the quantitative and qualitative maneuvering difficulties and thereby to assess the safety of ship navigation in that area.

The objective of this paper is to make clear the difference of maneuvering characteristics of a VLCC in standstill from those of her in running. The authors made mathematic models to calculate maneuvering motions of a VLCC in standstill using various ahead engine with full rudder angle and calculated their motions in each case and compared the calculated values with those of the same vessel running in sea trial tests. The difference of motions between them is great. For example, a VLCC in standstill can achieve a great alteration of heading over 90 degrees within the distance of 0.2L advance while she advances 3.0L for 90 degrees turning in full running sea trial turning test. Therefore whenever a VLCC in standstill meets a vessel approaching in collision course situation in near distance, it is better and recommendable that she should use her ahead engine with full rudder to avoid collision. So "maneuvering trial tests in standstill conditions" should be added to the content of sea trial tests when a newly built VLCC commence to take sea trials, that has not been included until now.

The total tug capacity needed for berthing/unberthing operations of a ship may vary depending on the ship's type, size, loading conditions, and environmental circumstances. Traditionally, total tug capacity is determined based on the local guidelines of port authorities or on the rule of thumb. However, the social demands for the enhancement of ship safety at harbor and the economical demands for the cost-effectiveness of tug usage makes it necessary for port authorities to develop more reasonable and detailed guidelines on tug usage which takes various conditions into account. In this paper, the method to estimate the optimum tug capacity of VLCC is suggested by considering various ship conditions such as its size, loading conditions, and environmental circumstances including wind, wave, tidal currents, and geographical characteristics of a terminal. This method is applied to the VLCC terminal located in Gwang-Yang harbor of Korea and the results are compared with the local guidelines of the harbor, which shows that there may be a room for the amendment of local guidelines on tug usage.

It is very important and necessary for safe maneuvering and piloting of a VLCC to know the quantity of her sinkage and trim changes in advance when she enters into shallow water area from deep sea. It is already well known that the quantity of sinkage and trim of a vessel change when she navigates between the sea areas of different depths. In this paper, the authors induced five mathematic formulas to compute the quantity of hull sinkage and trim changes arising from the different conditions and speeds of vessels and sea depth. Also they checked and examined the conditions of 131 VLCC class vessels with the over all lengths between 200 to 360 meters and evaluated mean values of Cb, Lpp/B, Lpp/dm, the trim and mean draft(dm) of them according to the different groups of length and loaded conditions. Using the calculating math formulas and loaded conditions, the authors math tables to find the quantity of hull sinkage and trim changes due to the different size, condition and speed of vessels and the depth of sea.

The practical shiphandlers, such as ship's captain, pilot and mooring master, in charge of the SBM app-roaches and mooring operations of loaded VLCC should have a highly advanced shiphandling skills because of taking advantage of the wind and current from ahead without assistance of big tugboats. But now except some approaching skills in the vicinity of SBM buoy or waiting anchorage we do not have an optimal controlled approaching maneuvers in the entire course of port approaches. Consequently this study presents the optimal SBM approaches to the practical shiphandlers of VLCC and puts to use with effect in the practical operations. The conclusions of this simulation study are as follows : 1) The optimal SBM approaches in combination of Woo's Approach and a large change of heading were presented for the practical shiphandlers, 2) According to simulation of the pilotship the angle of a large change of heading for reducing headway is more than 70 degrees approximately. 3) Applied this optimal approaches to the SBM operations of simulated Port of Ulsan and confirmed the control of ship and the economy of port approaches time.

In the North Pacific Ocean a lot of large waves set up in winter, affected by continued winds and swells owing to severe extratropical cyclones. Under this sea condition, if the ship is about 100,000L/T (in deadweight capacity tonnage), we can't find the danger involved in the ship at sea apparently. But when we compare the seaworthiness of ship's building strength with the stress given to the hull by waves, we can't insist that the former be more stronger than the latter. As a result, VLCC is in danger of destroying and cutting for lack of longitudinal strength in heavy weather. Up to this time, Naval Architects have actively studied the relation between ship's longitudinal strength and waves as a ship's projector; however, actually, they have never made more profound study on the problem of longitudinal strength in relation to navigation. The main puprpose of this thesis is to clarify these vivid actual states of ship's trouble unknown to ship's masters. In this thesis we picked up VLCC Pan Yard, a vessel of Pan Ocean Bulk Carrier company's, as a model ship. And in the North Pacific Ocean, we have chosen for this research the basins where the wind speed and the wave height are greater than average. The data used this thesis are quotes from the "winds and waves of the North Pacific Ocean('64-'73)", and wind speed more than 30 knots was made use of as an ocject of this study. By usinh the ITTC wave spectrum, we found out the significant waves for every 5 knots within the range of 20 knots to 45 knots of wind speed. According to this H1/1000 was calculated. The stress of ship's hull is determined by ship's speed and wave height. We compared the ship's longitudinal strength with a planned wave height by rules of several famous classification societies in the world. In the last analysis, we found out that ship's present planned strength in heavy weather is not enough. Finally we made a graph for avoiding heavy weather, with which we studied safe ship's handling in the North pacafic Ocean in winter.