수소는 다양한 신재생에너지 중 환경친화적인 에너지로 각광받고 있지만 농업에 적용된 사례는 드물다. 본 연구는 수소 연료전지 삼중 열병합 시스템을 온실에 적용하여 에너지를 절 약하고 온실가스를 줄이고자 한다. 이 시스템은 배출된 열을 회수하면서 수소로부터 난방, 냉각 및 전기를 생산할 수 있다. 수소 연료 전지 삼중 열 병합 시스템을 온실에 적용하기 위해 서는 온실의 냉난방 부하 분석이 필요하다. 이를 위해서는 온 실의 형태, 냉난방 시스템, 작물 등을 고려해야 한다. 따라서 본 연구에서는 건물 에너지 시뮬레이션(BES)을 활용하여 냉 난방 부하를 추정하고자 한다. 전주지역의 토마토를 재배하 는 반밀폐형 온실을 대상으로 2012년부터 2021년까지의 기 상데이터를 수집하여 분석했다. 온실 설계도를 참고하여 피 복재와 골조를 모델화하여 작물 에너지와 토양 에너지 교환을 실시했다. 건물 에너지 시뮬레이션의 유효성을 검증하기 위 해 작물의 유무에 의한 분석, 정적 에너지 및 동적 에너지 분석 을 실시했다. 또한 월별 최대 냉난방 부하 분석에 의해 평균 최 대 난방 용량 449,578kJ·h-1, 냉방 용량 431,187kJ·h-1이 산정 되었다.

Membranes techniques used to convert chemical energy into electrical energy from energy sources such as hydrogen, salt water, and water. Membrane materials have transport property of desire molecular and barrier property for satisfy to requirement of cell performance. Typically, PFSA polymer is used to fabricate membrane. Each material has different characteristics depending on the membrane formation conditions. Macroscopic characteristics are difficult to correlation with molecular motion, mobility, and transport within membrane matrices. NMR spectroscopy can analysis about these characteristics by observing the molecule level. In this study, NMR spectroscopy can provide fundamental information of PFSA ionomers and correlation with macroscopic characteristics.

Polymer electrolyte membrane (PEM) is one of key elements to determine both electrochemical performances and lifetimes of fuel cell electric vehicles (FCEVs). PEM is exposed to a variety of dynamic stimuli (e.g., temperature, humidity, pressure, fuel gases and so on) under their operation conditions and meets unavoidable mechanical damages derived from unequal pressure difference between anode and cathode feed gases. Even though there have been approaches to evaluate the mechanical strength of PEM materials, most of the trials could provide static information on their mechanical strength. In this study, a pressure-loaded blister hybrid system connected with gas chromatography was developed to disclose the efficacy of the system as an evaluation tool of dynamic PEM strength under realistic FCEV operation conditions.

본 연구에서는 탄화수소계열 고분자인 sulfonated poly arylene ether sulfone(SPAES) 고분자를 이용하여 연료전지용 전해질막을 제조하였으며 메탄올 투과도를 최적화 하기 위하여 소수성 고분자인 polyethersulfone(PES), Polyvinylidene fluoride (PVdF) 를 소량 첨가하여 블렌드막을 제조하였다. 제조된 분리막은 연료전지용 전해질 막으로써 요구되는 물리적, 화학적 안정성, 이온전도도, 셀 테스트등의 기본 물성을 측정하여 잠재적인 적용 가능성을 테스트 해보았다 또한 분자동력학 시뮬레이션을 이용하여 소수성 고분자와 SPAES고분자의 혼화성 측정과, 이온 및 메탄올 분자의 투과도를 예측해 보았으며 이를 이용하여 실제 실험 결과와 비교 분석을 진행하였다.

This study is focused on the channel design of bipolar plate in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv design of electrode. Since the flow rate and flow pattern of generated gas in the two phase flow system are the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL MultiphysicsTM to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator and flow pattern of two phase fluid in the electrode. In this study, liquid electrolyte flows into the bipolar plate and decomposed into gas phase, two phase flow simulation is applied to measure the efficiency of hydrogen gas generation.

This study is focused on the channel design of bipolar plate in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv design of electrode. Since the flow rate of generated gas is the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL MultiphysicsTM to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator.

Broadband networks are designed to support a wide variety of services with different traffic characteristics and demands for Quality of Services. Bandwidth allocation methods can be classified into two major categories： static and dynamic. In static allocation, bandwidth is allocated only at call setup time and the allocated bandwidth is maintained during a session. In dynamic allocation, the allocated bandwidth is negotiated during a session. The purpose of this paper is to develop policies for deciding and for adjusting the amount of bandwidth requested for a best effort connection over such as ATM networks.. This method is to develop such policies that a good trade off between utilization and latency using cell delay variation to the forecast the incoming traffic in the next period. The performances of the different polices are compared by simulations.

Broadband networks are designed to support a wide variety of services with different traffic characteristics and demands for Quality of Services. Bandwidth allocation methods can be classified into two major categories: static and dynamic. In static allocation, bandwidth is allocated only at call setup time and the allocated bandwidth is maintained during a session. In dynamic allocation, the allocated bandwidth is negotiated during a session. The purpose of this paper is to develop policies for deciding and for adjusting the amount of bandwidth requested for a best effort connection over such as ATM networks. This method is to develop such policies that a good trade off between utilization and latency using cell delay variation to the forecast the incoming traffic in the next period. The performances of the different polices are compared by simulations.

In plants, nitrogen is the major component for growth and development. Leaf growth is based on the division, elongation and maturation of cells, which are used for making of epidermis, mesophyll, bundle sheath, xylem, phloem and so on. Dynamics of these tissues with respect to nitrogen are required for better understanding. This experiment was conducted to evaluate effect of nitrogen on the elongation of epidermal and guard cell of two rice (Oryza sativa L.) varieties, Seoanbyeo and Dasanbyeo on May 2000 at Chungbuk national university in Cheongju. After transplaning the 20-day-old seedlings into a/5000 pots, the main characteristics related with cell elongation were investigated and evaluated. A maximum. leaf length reached at 7 or 8 days after emerging from the collar, and also the leaf elongation rates were greatly affected by the increase of N application rate. The initial and final cell length were about 17~mu~textrmm and 130~mu~textrmm , respectively. Cell divisions occurred within 1.0mm from leaf base. With die higher nitrogen application rate of 22 kg-N 10~textrma-1 , cell division per hour was greater 1.5 to 1.9 and 1.2 to 1.3 fold as compared to the N application rate of 0 and 11 kg-N 10~textrma-1 , respectively. Cell enlargement of epidermal and guard cell under higher N application rate (22kg-N 10~textrma-1 ) was finished within about 20 (Seoanbyeo) and 15 hours (Dasanbyeo), while it took much time, about 30 hours.