최근 도심지 버스정류장의 아스팔트 포장을 콘크리트 포장으로 전환하는 추세이다. 서울시에서는 헌릉로 구간 중앙버스정류장에 현 장타설 방식의 연속철근 콘크리트 포장(CRCP)을 국내 최초로 적용하였다. CRCP는 슬래브 내부에 철근을 연속적으로 배근하며 수축줄 눈을 두지 않고 균열을 허용하는 공법으로 균열폭 거동이 공용성에 중요한 영향을 미친다. 본 연구에서는 헌릉로 구간 중앙버스정류 장에 인력포설 방식으로 시공된 CRCP의 균열폭의 거동 특성을 계측을 통해 분석하였다. 균열폭 거동 계측은 자연발생균열 2개와 유 도균열 1개에 파이형 균열게이지를 설치하여 수행하였다. 하나의 자연균열은 일평균 균열폭 거동이 약 0.278mm로 분석되었으며 다른 하나의 자연균열은 균열폭 거동이 약 0.184mm로 분석되었다. 유도균열의 균열폭 거동은 약 0.144mm로 분석되어 자연균열에 비해 균 열폭 거동이 다소 작게 분석되었다. 이와 같이 도심지의 버스정류장에 적용한 CRCP는 시공초기에 균열폭이 매우 미소하여 이물질과 수분의 침투를 억제하며 줄눈 콘크리트 포장의 줄눈부에서의 스폴링 등 포장 파손을 저감하는데 효과적일 것으로 분석되었다.

도심지에 시공된 아스팔트 포장은 교통량 증가와 중차량의 가감속으로 인해 포트홀 및 소성변형 등의 파손이 흔히 발생하고 있다. 이러한 아스팔트 포장의 파손을 최소화하기 위해 콘크리트 포장으로 전환하는 공법인 초속경 시멘트 콘크리트 포장 공법과 프리캐스 트 콘크리트 포장 공법이 있으나 고비용으로 인해 널리 적용하기에는 한계가 있는 실정이다. 최근 서울시에서는 신설 중앙버스정류장 에 현장타설 방식으로 연속철근 콘크리트 포장(CRCP)을 시공하였다. 본 연구에서는 인력포설 방식으로 시공한 중앙버스정류장의 CRCP에 대한 공용성을 분석하고자 온도계, 균열유도장치, 철근 변형률계, 콘크리트 변형률계, 변위계, 균열계 등을 포함하는 계측시스 템을 구축하였으며 본 논문에서는 이러한 계측시스템에 대하여 기술한다.

국내 고속도로의 본선차로 포장은 시공비용이 저렴한 줄눈 콘크리트 포장을 주로 시공하였으나, 최근 유지보수비용이 증가함에 따 라 유지관리비용이 저렴하고 공용성이 뛰어난 연속철근 콘크리트 포장을 확대 적용하고 있는 추세이다. 그러나 본선차로가 연속철근 콘크리트 포장으로 시공될 때 접속차로의 포장은 대부분 줄눈 콘크리트 포장으로 시공하고 있어 서로 다른 포장 형식이 접속함으로 인해 거동 차이가 발생하여 접속부에서 파손이 발생하기도 한다. 따라서 본 연구에서는 본선차로 연속철근 콘크리트 포장과 접속차로 줄눈 콘크리트 포장을 시공할 경우 줄눈 간격에 따른 접속차로 줄눈 콘크리트 포장의 응력 특성을 분석하기 위하여 유한요소해석 프 로그램을 이용하여 구조해석을 수행하였다. 줄눈 간격별로 줄눈 콘크리트 포장의 해석모델을 구성하였으며 환경하중인 선형수직온도 경사와 온도하강, 그리고 선형수직온도경사와 온도하강을 동시에 적용하여 해석을 실시하였다. 구조해석 결과, 모든 온도조건에서 줄 눈 간격이 좁아질수록 슬래브와 타이바의 응력이 감소하는 것으로 나타났다.

PURPOSES : The purpose of this study is to verify the effectiveness of the developed ultra-thin-continuously reinforced concrete partition (UT-CRCP) overlay method through a comparative analysis of the early-behavior of the UT-CRCP with a 100 mm cutting overlay of the existing JPCP. METHODS : This study aims to minimize the vulnerability of the existing JPCP (joint section behavior) by overlaying the continuous reinforcement form to constrain joint behavior. For this purpose, the early-behavior of the JPCP section was measured and the early-behavior of the UT-CRCP section was compared with that of the cutting overlay of the same section. The testbed was constructed for comparative analysis of the two types of pavements and the early behavior was measured using the pure environmental loads, i.e., situations where there was no traffic load. For the UT-CRCP, which is a comparative test group, UT-CRCP was constructed approximately one year after the JPCP was constructed by milling the top of the existing JPCP by 100 mm. RESULTS : 1) UT-CRCP was shown to effectively reduce the amount of crack width change on the surface by 17 %, compared to JPCP, by placing reinforcement inside the pavement. 2) The restricting effect of the UT-CRCP was analyzed by comparing the strain generated by the cross-section depth for the two pavement types. As a result, the restricting rate by depth (20, 80, 120, and 280 mm) was 68.4 %, 80.2 %, 89.2 %, and 26.7 %, respectively. 3) We reviewed the comprehensive gauge restricting rate at depths of 80 mm and 120 mm (80.2 % and 89.2 %, respectively) and the absolute value of behavior that is located at the ±20 mm of the interface of JPCP and UT-CRCP. Thus, it was possible to estimate that both layers of pavements exhibit the same behavior (tied) at the interface between the two pavement layers. CONCLUSIONS : In this study, the early behavior of the BCO concept UT-CRCP overlay technique was analyzed and quantitatively presented to overcome the limitations of JPCP with relatively weak point behavior and to increase the commonality of aged concrete pavement to the performance of the new pavement.

As of 2016, Texas Department of Transportation (TxDOT) manages a total of 16,327 lane miles of Portland cement concrete (PCC) pavement, which represents an important asset to TxDOT. As PCC pavements in Texas built in the 1960s through 1980s have already exceeded or are approaching the end of their design lives, many of these projects will require rehabilitations of some form. Considering the expected steady increase in truck traffic in the future, PCC overlays represent one of the best options for that rehabilitation. Currently, guidelines on PCC pavement overlays on PCC pavement focus on overlay slab thickness determination, but do not provide clear directions on whether existing PCC pavement is a good candidate for concrete overlay, or if the pavement is a good candidate, which overlay type –bonded concrete overlay (BCO) or unbonded concrete overlay (UBCO) –is appropriate. Sound guidelines are needed for the selection of an optimum overlay type, especially for continuously reinforced concrete pavement (CRCP) overlays, which could extend the performance period of structurally deficient PCC pavements in Texas at a reasonable cost. In the present study, the evaluations of PCC overlay performance of various BCO and UBCO projects built in Texas were conducted to develop the BCO design procedures based on mechanistic-empirical principles, and the development of design guidelines for the selection of an optimum overlay type.

PURPOSES : The purpose of this study is to investigate characteristics of crack spacing and crack width and their relationship in continuously reinforced concrete pavement (CRCP) based on the data obtained from long-term field observations. METHODS: The crack spacings and crack widths are measured periodically over 10 years at two different CRCP sections: one with asphalt bond breaker beneath concrete slab, and the other with bonded lean concrete base beneath concrete slab. The effects of steel ratio, type of underlying layer, terminal treatment method, and seasonal temperature change on the crack characteristics are evaluated by analyzing the measured data. RESULTS: The CRCP with lean concrete base shows smaller crack spacings than those of the CRCP with asphalt bond breaker. As the steel ratio increases, both the crack spacing and crack width tend to decrease. The crack width becomes larger as the crack age increases, but once the crack age is over a certain value the crack width tends to converge. When the terminal anchor lug system is not used and the expansion joints are employed at the terminals, the crack spacings and crack widths increase near the terminal sections. The crack spacing and crack width seem to be proportional each other, but not necessarily linearly, and their relationship is more distinguished in the summer when the crack widths become smaller. CONCLUSIONS : The steel ratio, underlying layer type, terminal treatment method, and seasonal temperature change affect the characteristics of cracks and the crack spacing and crack width are related to each other.

In a wide spectrum of pavement rehabilitation techniques, the application of thin asphalt overlay on existing concrete pavements have shown its ability to restore the functional capacity of the pavement system as well as maintain structural capacity. Although, prior researches stated that it does not add to the structural capacity of the existing pavement, the insulation generated by the asphalt overlay can affect the behavior of the discontinuities in the continuously reinforced concrete pavement (CRCP) system by reducing the magnitude of its movement. The investigation of crack movement behaviors of the CRCP in Chungbu Expressway was conducted in 2-phases: without overlay and with overlay. Crackmeters were installed at selected crack locations and measurements were collected. In the second phase of the investigation, crackmeters were installed at the concrete layer of the CRCP before a 2-inch asphalt overlay was applied. Results have shown that the crack movements under a thin asphalt overlay have reduced by 80% which indicates an effective insulation of the CRCP.

PURPOSES : The field application and performance of continuously reinforced concrete pavement (CRCP), constructed by using the mechanical tube-feeding method, are evaluated in this study. METHODS: The location of the rebar was evaluated by using the MIRA system. The early-age CRCP performance was evaluated via visual survey, in which the crack spacing and crack width were examined. RESULTS: The location of longitudinal reinforcing bars was evaluated via MIRA testing and the results showed that the longitudinal rebars all lie within a given tolerance limit (±2.5 cm) of the target elevation. In addition, owing to the low temperature when the concrete was pured, the crack spacing in the Dae-Gu direction is slightly wider than that of the Gwang-Ju direction. Almost all of the crack spacings lay within the range of 1.0 m~3.0 m. A crack width of <0.3 mm was measured at the pavement surface. However, as revealed by the field survey, the crack spacing was not correlated with the crack width. CONCLUSIONS : In CRCP constructed by using the mechanical tube-feeding method, almost all of the longitudinal reinforcing bars lay within the tolerance limit (2.5 cm) of the target elevation. The concrete-placing temperature affects the crack spacing, owing to variations in the zero-stress temperature. Crack survey results show that there is no correlation between the crack spacing and crack width in CRCP.

PURPOSES : The purpose of this study is to develop a method for improving the accuracy of analysis results obtained from a twodimensional (2-D) numerical analysis model of continuously reinforced concrete pavement (CRCP). METHODS: The analysis results from the 2-D numerical model of CRCP are compared with those from more rigorous three-dimensional (3- D) models of CRCP, and the relationships between the results are recognized. In addition, the numerical analysis results are compared with the results obtained from field experiments. By performing these comparisons, the calibration factors used for the 2-D CRCP model are determined. RESULTS : The results from the comparisons between 2-D and 3-D CRCP analyses show that with the 2-D CRCP model, concrete stresses can be overestimated significantly, and crack widths can either be underestimated or overestimated by a slight margin depending on the assumption of plane stress or plane strain. The behaviors of crack width in field measurements are comparable to those obtained from the numerical model of CRCP. CONCLUSIONS: The accuracy of analysis results from the 2-D CRCP model can be improved significantly by applying calibration factors obtained from comparisons with 3-D analyses and field experiments.

PURPOSES: The purpose of this study is to evaluate the degree of restraint (DOR) of longitudinal steel at continuously reinforced concrete pavement (CRCP) against environmental loadings. METHODS : To measure the longitudinal steel strain, 3-electrical resistance and self-temperature compensation gauges were installed to CRCP test section (thickness = 250mm, steel ratio = 0.7%) and continuously measured 10 min. intervals during 259 days. In order to properly analyze the steel strains first, temperature compensation process has been conducted. Secondly, measured steel strains were divided into 12 phases with different events such as before paving, during concrete hardening, and after first cracking, etc. RESULTS : Thermal strain rate (TSR) concept is defined as the linear strain variations with temperature changes and restraints rate of longitudinal steel against environmental loadings (especially thermal loading) with different cases is defined as degree of restraint(DOR). New concept of DOR could be indirect indicator of crack width behaviors of CRCP. CONCLUSIONS: Before paving, DOR of longitudinal steel is almost same at the coefficient of thermal expansion of steel (12.44m/m/℃) because of no restraint boundary condition. After concrete pouring, DOR is gradually changed into -1 due to concrete stiffness developing with hydration. After first cracking at crack induced area, values of DOR are around -3~-5. The negative DOR stands for the crack width behavior instead of steel strain behavior. During winter season, DOR reached to -5.77 as the highest, but spring this values gradually reduced as -1.7 as the lowest. Based on this observation, we can presume crack width decreased over time within the time frame of this study. This finding is not consistent with the current theory on crack width variations over time, so further study is necessary to identify the causes of crack width reducing. One of the reasons could be related to concrete stress re-distribution and stress relaxation.

PURPOSES : The purpose of this study is to analyse the longitudinal steel strain and stress of continuously reinforced concrete pavement(CRCP) with longitudinal and transverse direction at early age using stress dependent strain analysis method. METHODS : To measure the longitudinal steel strain, 9-electrical resistance and self-temperature compensation gauges were installed to CRCP test section (thickness = 250mm, steel ratio = 0.7%) and continuously measured 10min. intervals during 30days. In order to properly analyze the steel stress first, temperature compensation process has been conducted. Secondly, measured steel strains were divided into stress dependent strain (elastic strain) and stress independent strain (thermal strain) and then stress dependent strain was applied to stress calculation of longitudinal steels. RESULTS: Steel strains were successfully measured during 30days. To verify the accuracy of temperature compensation process, measured coefficient of thermal expansion(COTE,11.46×10-6m/m/℃) of longitudinal steel before paving was compared with that of unrestrained steel. Max. steel stress in the transverse direction shows about 266MPa at 23days after placement. CONCLUSIONS: Steel stresses in the longitudinal and transverse direction have been evaluated. In longitudinal direction, steel stress from the crack was rapidly reduced from 183MPa at crack to 18MPa from 600mm apart the crack. From this observation, stress effective length can be identified as within 600mm apart from the crack. In transverse direction, max. stress point was located near the center of pavement width and stress level(266MPa) is about 66% of yield stress of steel

PURPOSES: The objective of this study is to evaluate construction issues and design for transverse steel in continuously reinforced concrete pavement(CRCP). METHODS : The first continuously reinforced concrete pavement(CRCP) design procedure appeared in the 1972 edition of the“ AASHTO Interim Guide for Design of Pavement Structures,”which was published in 1981 with Chapter 3 “Guide for the Design of Rigid Pavement” revised. A theory that was accepted at that time for the analysis of steel stress in concrete pavement, called subgrade drag theory(SGDT), was utilized for the design of reinforcement of CRCP - tie bar design and transverse steel design - in the aforementioned AASHTO Interim Guide. However SGDT has severe limitations due to simple assumptions made in the development of the theory. As a result, any design procedures for reinforcement utilizing SGDT may have intrinsic flaws and limitations. In this paper, CRCP design procedure for transverse steel was introduced and the limitations of assumptions for SGDT were evaluated based on various field testing. RESULTS: Various field tests were conducted to evaluate whether the assumptions of SGDT are reasonable or not. Test results show that 1) temperature variations exist along the concrete slab depth, 2) very little stress in transverse steel, and 3) warping and curling in concrete slab from the field test results. As a result, it is clearly revealed out that the assumptions of SGDT are not valid, and transverse steel and tie bar designs should be based on more reasonable theories. CONCLUSIONS : Since longitudinal joint is provided at 4.1-m spacing in Korea, as long as joint saw-cut is made in accordance with specification requirements, the probability of full-depth longitudinal cracking is extremely small. Hence, for transverse steel, the design should be based on the premise that its function is to keep the longitudinal steel at the correct locations. If longitudinal steel can be placed at the correct locations within tolerance limits, transverse steel is no longer needed.

PURPOSES : This paper numerically evaluates the contribution of transverse steel to the structural behavior of continuously reinforced concrete pavements to understand the role of transverse steel. METHODS: Two-lane continuously reinforced concrete pavements with and without transverse steel were analyzed through finite element analysis with the aid of commercial finite element analysis program DIANA; the difference in their structural behavior such as deflection, joint opening, and stress distribution was then evaluated. Twenty-node brick elements and three-node beam elements were used to model concrete and steel, respectively. Sub-layers were modeled with horizontal and vertical tensionless spring elements. The interactions between steel and surrounding concrete were considered by connecting their nodes with three orthogonal spring elements. Both wheel loading and environmental loading in addition to self-weight were considered. RESULTS : The use of transverse steel in continuously reinforced concrete pavements does not have significant effects on the structural behavior. The surface deflections change very little with the use of transverse steel. The joint opening decreases when transverse steel is used but the reduction is quite small. The transverse concrete stress, rather, increases when transverse steel is used due to the restraint exerted by the steel but the increase is quite small as well. CONCLUSIONS : The main role of transverse steel in continuously reinforced concrete pavements is supporting longitudinal steel and/or controlling unexpected longitudinal cracks rather than enhancing the structural capacity.