This article reported a simple method for preparing diamond/SiC composites by polymer impregnation and pyrolysis (PIP) process, and the advantages of this method were discussed. Only diamond and SiC were contained in the diamond/SiC composite prepared by PIP process, and the diamond particles remained thermally stable up until the pyrolysis temperature was increased to 1600 °C. The pyrolysis temperature has a significant impact on the thermal conductivity and dielectric properties of composites. The thermal conductivity of the composite reaches a maximum value of 63.9 W/mK when the pyrolysis temperature is 1600 °C, and the minimum values of the real and imaginary part of the complex permittivity are 19.5 and 0.77, respectively. The PIP process is a quick and easy method to prepare diamond/SiC composites without needing expensive equipment, and it is of importance for promoting its application in the field of electric packaging substrate.

본 연구는 관상가치가 있는 자생 참두메부추와 갯부추를 절화소재로 이용하고자 수행되었다. 실험은 절화가 수확된 직후, gibberellic acid(GA3) 50, 75, 100mg·L-1, silver thiosulfate(STS) 0.1, 0.3, 0.5mM, 8-hydroxyquinoline sulfate(8-HQS) 25, 50, 100mg·L-1, 그리고 시중에 판매되 고 있는 Chrysal 8mL·L-1, Floralife 10mL·L-1의 보존용액 에 처리되었다. 참두메부추의 절화수명 연장에는 Chrysal 보 존용액 처리가 가장 효과적이었으며 다음으로 75mg·L-1 GA3 처리가 효과적이었다. 한편 8-HQS와 STS는 참두메부추의 절화수명을 단축하고 줄기가 갈변하는 등의 부정적인 영향을 끼쳤다. Chrysal과 더불어 Floralife 보존용액 처리는 절화 참두메부추의 상대 생체중변화율을 높이는데 효과가 있었다. 반면 갯부추는 100mg·L-1 GA3 처리에서 절화수명이 유일하 게 7일까지 연장되었다. GA3 보존용액 처리를 제외한 다른 처리에서 갯부추의 절화수명은 증류수인 대조구보다 비슷하 거나 약간 높은 수준이었다. 절화 갯부추의 수분흡수율은 실 험 초반 100mg·L-1 8-HQS 처리에서, 상대 생체중변화율은 Chrysal 보존용액 처리에서 가장 높게 조사되었으나 두 처 리 모두 절화수명이 유의하게 연장되지 않았다. 갯부추는 100mg·L-1 GA3 처리에서 절화수명을 비롯한 절화품질이 가 장 우수하였다.

목적 : 본 연구는 중국의 옵토메트리 교육제도의 현황을 조사하고 분석하였으며, 중국 옵토메트리 교육에 대한 문제점을 고찰하고자 하였다. 방법 : 중국의 옵토메트리 관련 정보는 중국학술정보원(China National Knowledge Infrastructure, CNKI), 중국안경협회(China Optomatric and Optical Association, COOA), 중화인민공화국교육부, 바이두(baidu) 및 학술연구정보서비스(Research Information Sharing Service, RISS)을 통해 수집되었다. 결과 : 중국의 교육제도에 따르면, 중국의 옵토메트리스트는 중등직업학교(3년제), 전문대학(3년제), 종합대학 (4년제), 의과대학(5년제) 및 단기 직업기능훈련기관 등에서 각각 배출되고 있는 것으로 나타났다. 또한 총 학점 (수업 시간)은 각각 중등직업학교 152점(3,120시간), 전문대학 154점(2,800시간), 종합대학 중 촨베이이쒜위엔 (천북의학원)은 205.5점(3,795시간), 산동디이이커따쒜(산동제일의과대학)는 166점(2,730시간) 및 의과대학 중 난징이커따쒜(남경의과대학)는 297점(3,786시간), 원저우이커따쒜(온주의과대학)는 230.5점(3,249시간)으로 나타 났다. 결론 : 중국 내 옵토메트리 교육 현황 및 교육제도를 조사하였으며 교육의 체계적인 관리와 인력의 수행 능력 평가 방안이 아직 미흡한 것으로 나타났으며 향후 이러한 문제점을 개선할 필요가 있다고 판단된다.

As the decommissioning and decontamination (D&D) of nuclear power plants (NPPs) has actively proceeded worldwide, the management of radiation exposure of workers has become more critical. Radioactive aerosol is one of the main causes of worker exposure, contributing to internal exposure by inhalation. It occurs in the process of cutting radioactive metal structures or melting radioactive wastes during D&D, and its distribution varies according to decommissioning strategies and cutting methods. Among the dominant radionuclides in radioactive aerosols, Fe-55 is known to be the most abundant. Fe-55, which decays by electron capture, is classified as a difficult-to-measure (DTM) radionuclide because its emitted X-rays have too low energy to measure directly from outside of the container. Generally, for measuring DTM nuclides, the liquid scintillation counting (LSC) method and the scaling factor (SF) method are used. However, these methods are not suitable for continuous monitoring of the D&D workplace due to the necessity of sampling and additional analysis. The radiation measurement system that can directly measure the radionuclides collected at the aerosol filter could be more useful. In this study, as preliminary research on developing the radioactive aerosol monitoring system, we fabricated a gamma-ray spectrometer based on a NaI (Tl) scintillator and measured the energy spectrum of Fe-55. A beryllium window was applied to the scintillator for X-ray transmission, and the Fe-55 check source was directly attached to the scintillator assuming that the aerosol filter was equipped. 5.9 keV photopeak was clearly observed and the energy resolution was estimated as 44.10%. Also, the simultaneous measurement with Cs-137 was carried out and all the peaks were measured.

Plastic scintillators can be used to find radioactive sources for portal monitoring due to their advantages such as faster decay time, non-hygroscopicity, relatively low manufacturing cost, robustness, and easy processing. However, plastic scintillators have too low density and effective atomic number, and they are not appropriate to be used to identify radionuclides directly. In this study, we devise the radiation sensor using a plastic scintillator with holes filled with bismuth nanoparticles to make up for the limitations of plastic materials. We use MCNP (Monte Carlo N-particle) simulating program to confirm the performance of bismuth nanoparticles in the plastic scintillators. The photoelectric peak is found in the bismuth-loaded plastic scintillator by subtracting the energy spectrum from that of the standard plastic scintillator. The height and diameter of the simulated plastic scintillator are 3 and 5 cm, respectively, and it has 19 holes whose depth and diameter are 2.5 and 0.2 cm, respectively. As a gamma-ray source, Cs-137 which emits 662 keV energy is used. The clear energy peak is observed in the subtracted spectrum, the full width at half maximum (FWHM) and the energy resolution are calculated to evaluate the performance of the proposed radiation sensor. The FWHM of the peak and the energy resolution are 61.18 keV and 9.242% at 662 keV, respectively.

Organic complexing agents may affect the mobility of radionuclides at low- and intermediate-level radioactive waste repositories. Especially, isosaccharinic acid (ISA) is the main cellulose degradation product under high pH conditions in cement pore water. ISA can combine with radionuclides and form stable complexes that adversely influence adsorption in the concrete phase, resulting in radionuclides to leach to the near- and far-fields of repositories. This study focuses on investigating the sorption of ISA onto engineered barriers such as concrete, thereby studying adsorption isotherms of ISA on concrete and comparing various isotherm models with the experimental data. The adsorption experiment was conducted in three background solutions, groundwater (adjusted to pH 13 using NaOH), State 1 (artificial cement pore water, pH 13.3), and State 2 (artificial cement pore water, pH 12.5), in a batch system at a temperature of 20°C. Concrete was characterized using BET, Zeta-potential analyzer, XRD, XRF, and SEM-EDS. ISA concentrations were detected using HPLC. The experimental data were best fitted to one-site Langmuir isotherm; On the other hand, either two-site isotherm or Freundlich isotherm couldn’t give reasonable fitting to the experimental data. The observed ISA sorption behavior on concrete is crucial for the disposal of radioactive waste because it can significantly lower the concentration of ISA in the pore water. Although one-site Langmuir isotherm might effectively represent the sorption behavior of ISA on concrete, the underlying mechanism is still unknown, and further investigation should be done in the near future.

Engineered barriers (concrete and grout) in Low- and Intermediate-Level Waste (L/ILW) disposal facilities tend to degrade by groundwater or rainfall water over a long period of time. During the degradation process, radionuclides stored in the disposal facility might be released into the pore water, which can pass through the natural rock barriers (granite and sedimentary rock) and may reach the near-field and far-field. In this transportation, radionuclide might be sorbed onto the engineered and natural rock barriers. In addition, the organic complexing agent such as ethylenediaminetetraacetic acid (EDTA) and α-isosaccharinic acid (ISA), is also present in pore water, which may affect the sorption and mobility of radionuclide. In this study, the sorption and mobility of 90Sr under different conditions such as two pHs (7 and 13), different initial concentrations of organic complexing agents (from 10-5 M to 10-2 M), and solutions (groundwater, pore water, and rainfall water) were investigated in a batch system. The groundwater was collected at the L/ILW disposal facility located at Gyeongju in South Korea. The pore water and rainfall water were artificially made in the laboratory. The concrete, grout, granite, and sedimentary rock samples were collected from the same study sites from where the groundwater was collected. The rock samples were crushed to 53-150 micrometers and were characterized by XRD, XRF, SEM-EDS, BET, and zeta potential analyzer. 90Sr concentration was determined using liquid scintillation counting. The sorption of 90Sr was described by distribution coefficients (Kd) and sorption reduction factor (SRF). In the case of EDTA, the Kd values of 90Sr remained constant from 10-5 M to 10-3 M and tended to decrease at 10-2 M, while in case of ISA the Kd values decreased steadily as the concentration of ISA was increased from 10-5 M to 10-3 M; However, a sudden reduction in the Kd values were observed above 10-2 M. In comparison to EDTA, ISA gave a higher SRF of 90Sr. Therefore, from the above results, it can be concluded that the presence of ISA has a greater effect on the sorption and mobility of radionuclide in the solutions than EDTA, and the radionuclide may reach near- and far-field of the L/ILW disposal facility.

Radionuclides stored in a radioactive waste repository over a long period of time might be leached through the barriers such as engineered rock (cement) and natural rock (granite). Organic complexing agents such as ethylenediaminetetraacetic acid (EDTA) and isosaccharinic acid (ISA) may also influence the mobility of radionuclides. In this study, a continuous fixed-column reactor packed with engineered and natural rocks was designed to investigate the effect of organic complexing agents on cesium mobility through cement and granite under anaerobic conditions. The influent flow rate of the mixed solution (organic complexing agent and cesium) at the column bottom was 0.1 mL/min, while that of groundwater was 0.2 mL/min, which was introduced between cement and granite layers in the middle of the column. The hydraulic properties such as diffusion coefficient and retardation factor were derived by a bromide tracer test. The effects of different operating parameters, such as initial cesium concentrations, initial EDTA or ISA concentrations, and bed size, on the cesium adsorption were investigated. The Thomas, Adams-Bohart, and Yoon-Nelson models were applied to the experimental data to predict the breakthrough curves using non-linear regression. These results suggest that organic complexing agents such as EDTA and ISA significantly influence the mobility of cesium in the barriers, indicating that the presence of complexing agents enhances the migration of cesium to the geosphere.

Radionuclides can be leached into groundwater or soil over a long period of time due to unexpected situations even after being permanently disposed of in a repository. Therefore, it is necessary to investigate the mobility of radionuclides for the safety assessment of radioactive waste disposal. In this study, the effects of organic complexing agents such as ethylenediaminetetraacetic acid (EDTA) and isosaccharinic acid (ISA) on the sorption behavior of 239Pu and 99Tc over cementitious (concrete and grout) and natural rock samples (granite and sedimentary rock) were investigated in batch sorption experiments. For characterization of rock samples, XRD, XRF, FT-IR, FE-SEM, BET, and Zeta-potential analyses were performed. For the evaluation of mobility, the distribution coefficient (Kd) was selected and compared. The adsorption experiment was carried out at two pHs (7 and 13), a temperature of 20°C, and a range of organic complexing agents concentrations (10-7~10-2 M and 10- 5~10-2 M for 239Pu and 99Tc, respectively). The radionuclides concentrations in adsorption samples were analyzed using ICP-MS. The Kd values for 239Pu in all rock samples reduced significantly due to the presence of EDTA, even at low concentrations such as 10-5 M. In the case of ISA, the limiting noeffect concentration was much higher than that of EDTA. On the other hand, 99Tc showed relatively lower Kd values than 239Pu, and the sorption behavior of 99Tc was almost unaffected by the organic complexing agents for all rock samples. Therefore, it is possible to assume that the increased mobility of radionuclides, especially, 239Pu, in groundwater caused by the lowering of sorption at even low concentrations of organic complexing agents may result in the transport of radionuclides to the nearand far-field location of the repository.

Organic complexing agents which are contained in the radioactive waste can form the complex with radionuclides and enhance the solubility of radionuclides. The mobility of radionuclides to the far-field from the repository will be increased by radionuclide-ligand complex formation. Therefore, the assessment of the radionuclides’ solubility should be performed in the presence of organic complexing agents. In this study, five radionuclides (cobalt, strontium, iodine, cesium, and uranium) and three organic complexing agents (ethylenediaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), and isosaccharinic acid (ISA)) were selected as model radionuclides and organic complexing agents, respectively. For simulating the in-situ condition, the groundwater near the repository was collected and applied in solubility experiments and the solubility was measured in various environmental conditions such as different pHs (7, 9, 11, and 13), temperatures (10°C, 20°C, and 40°C), and a range of organic complexing agent concentrations (10-5, 10-4, 10-3, and 10-2 M). In cases of cesium and iodine, they were very soluble in all conditions, and the effect on their solubilities was not observed. However, at high pHs, cobalt and strontium showed lower solubilities than at neutral pH and the solubility enhancement by the organic complexing agents was significant. Moreover, the effects of each organic ligand showed obvious differences and were in the order of EDTA > NTA > ISA. The solubility of uranium was increased with increasing the organic ligand concentration at lower pHs, but the organic complexing agents did not cause a remarkable difference at high pHs. According to these results, the presence of complexing agents could enhance the radionuclides’ solubility and increase the potential to release the radionuclides to the far-field from the repository. Solubility experiments of other major radionuclides in the repository are in progress.

This study was conducted to investigate the forage characteristics of very early-maturing Italian ryegrass (IRG) three cultivars within September, 2021 to July, 2022 in Cheonan, Korea. We used three different cultivars of Italian ryegrass in this study “Greenfarm” “Greenfarm2ho” and “Greenfarm3ho” The results of heading date in this study, “Greenfarm” was recorded 3 days earlier than the other two cultivars, and its lodge tolerance score was the highest among the three. However, in case of plant length, there was no significantly difference in whole cultivars, in addition disease resistance, insect resistance and cold tolerance were not significantly different in three cultivars. The forage productivity of “Greenfarm2ho” was recorded the highest, especially the 1st harvesting of “Greenfarm2ho” yielded significantly the highest and superior to other varieties. As a result of feed value analysis, three cultivars were generally superior to overseas varieties and in particular, “Greenfarm2ho” was recorded to have excellent value because of the lowest NDF and ADF content. On the other hand, there was no significant difference in crude protein content among three varieties. In case of the monosaccharides content "Greenfarm3ho” had significantly higher glucose content than other two varieties, therefore the “Greenfarm” has advantage for preparing high quality of silage. In contrast, there was no significant difference among three varieties in fructose content.

High-temperature friction performances of graphite blocks (GBs) and zinc phosphate impregnated graphite blocks (IGBs) were evaluated under various friction temperatures. The surface of IGB exhibited extremely lower average friction coefficient values, that was 0.007 at 400 °C and 0.008 at 450 °C, in comparison to that of GB (0.13 at 400 °C and 0.16 at 450 °C, respectively). The worn surface of IGB in the high-temperature friction test was smoother and more complete than that of GB. The wear under high temperature and load caused the transformation of zinc pyrophosphate to zinc metaphosphate and the formation of a continuous large-area boundary lubrication layer combined with graphite and metallic element on the wear surface. The superior tribology property of IGB could be attributed to the digestion of iron oxides by tribo-chemical reactions and passivation of the exposed dangling covalent bonds. Specifically, the layered structure generated on the IGB wear interface effectively decreased the adhesive forces and prevented the surface from serious damage.

Nitrophenol sensors have garnered interest in pharmaceuticals, agriculture, environment safety and explosives. Various methods have been proposed to detect 4-nitrophenol, but nitrophenol isomers such as 2,4-dinitrophenol (DNP) and 2,4,6-trinitrophenol have been comparatively less studied. For the first time, the present work explores graphitic nanocarbon, i.e., carbon black (CB) interface for sensing of DNP. Two reduction potentials were noted at − 0.48 and − 0.64 V for o-NO2 and p-NO2 moieties, respectively, at CB/GCE. At the same time, bare GCE (glassy carbon electrode) shows a single reduction potential at − 0.7 V. The electrocatalytic effect and adsorption ability of the interface was studied from the DNP concentration effect. Scan rate and pH studies suggest that the CB acquires four electrons for NO2 reduction by the diffusion phenomenon. A broad detection range of 10–250 μM DNP with a very low detection limit of 0.13 (o-form) and 0.15 μM (p-form) was achieved using the CB interface. The real-time applicability of the fabricated sensor was evaluated using commercially available beverages with excellent recovery values. The stability, repeatability and reproducibility of the CB interface were successfully confirmed. Comparison of the sensing parameters of the developed sensor with those reported in literature reveals excellent detection limit and response time for the CB-interfaced DNP sensor, indicating its potential for environmental and commercial applications.

Abstract Biosensors are a group of measurement systems and their design is based on the selective identification of analyses based on biological components and physical and chemical detectors. Biosensors consist of three components: biological element, detector, and converter. The design of biosensors in various fields of biological sciences, medicine has expanded significantly. Biosensor technology actually represents a combination of biochemistry, molecular biology, chemistry, physics, electronics, and telecommunications. A biosensor actually consists of a small sensor and biological material fixed on it. Because biosensors are a powerful tool for identifying biological molecules, today they are used in various medical sciences, chemical industry, food industry, environmental monitoring, pharmaceutical production, health, etc. In fact, these sensors are a powerful tool to identify biological molecules. In fact, biosensors are analytical tools that can use biological intelligence to detect and react with a compound or compounds, and thus create a chemical, optical, or electrical message. The basis of a biosensor is to convert a biological response into a message. In this category, the use of telecommunication engineering technology and electromagnetic waves and frequency and radio spectrum is growing more and more to detect, measure, and determine the desired parameters in microbiology and laboratory sciences. The use of radio, optical, electromagnetic, ultrasonic, and infrared wave detection technology is part of the applications of telecommunication science in this field. Even image and audio processing systems have been instrumental in the discussion of biosensors in microbiology. The science of using fiber optics and waveguides, micro-strip antennas, and microelectromechanical technology is also very efficient in the construction and design of these biosensors.

The purpose of this study was to examine the extent to which influencing factors impact the transference willingness of farmers. The research method is based on the survey data on transference willingness, and the binary logistic model was used to analyze the influencing factors. The results show that the educational level, annual household income, farm labor, and farmers' understanding of land transfer policy notably influence land transfer. Based on the results, suggestions include improving farmers' social security system, improving a sound market for rural land transfer, and deepening the promotion and explanation of land-related policies.

Diamond reinforced silicon carbide matrix composites (diamond/SiC) with high thermal conductivity were prepared by tape casting combined with Si vapor infiltration for thermal management application. The effects of the mixing mode of bimodal diamond particles on the microstructure, thermal and mechanical properties of the composites were analyzed. The results reveal that the thermal conductivity of composites is affected significantly by mixing mode of diamond. In general, when the content of large diamond remains constant, adding a slight amount of small diamond was found to be effective in improving the thermal conductivity of the composite. However, excess small diamonds added will decrease thermal conductivity due to its high interfacial thermal resistance. The maximum thermal conductivity of obtained diamond/SiC is 469 W/(m K) when 38 vol% large diamond and 4 vol% small diamond were added. Such a result can be attributed to the formation of efficient heat transfer channels within the composite and sound interfacial bonding between diamond and SiC phase. Diamond/SiC with high thermal conductivity are expected to be the next generation of electronic packaging substrate.