Thermal management is significant to maintain the reliability and durability of electronic devices. Heat can be dissipated using thermal interface materials (TIMs) comprised of thermally conductive polymers and fillers. Furthermore, it is important to enhance the thermal conductivity of TIMs through the formation of a heat transfer pathway. This paper reports a polymer composite containing vertically aligned electrochemically exfoliated graphite (EEG). We modify the EEG via edge selective oxidation to decorate the surface with iron oxides and enhance the dispersibility of EEG in polymer resin. During the heat treatment and curing process, a magnetic field is applied to the polymer composites to align the iron oxide decorated EEG. The resulting polymer composite containing 25 wt% of filler has a remarkable thermal conductivity of 1.10 W m− 1 K− 1 after magnetic orientation. These results demonstrate that TIM can be designed with a small amount of filler by magnetic alignment to form an efficient heat transfer pathway.

Investigations and monitoring of environmental radiation are important for preventing expected accidents or for early detection of unexpected accidents, in nuclear facilities and the surrounding. In the event of an environmental radiation accident, it should be possible to identify and analyze the radiation-contaminated area. Therefore, a rapid radiation monitoring system is required for immediate response and necessary measures. In this study, the distribution of radiation mapping is performed on a contaminated area using 2-dimensional or 3-dimensional contour mapping techniques. The entire surrounding area can be understood at a glance by displaying the radiation contour line on the map of the measured area.

When decommissioning a nuclear power plant, the structure must be made to a disposable size. In general, the cutting process is essential when dismantling a nuclear power plant. Mainly, thermal cutting method is used to cutting metal structures. The aerosols generated during thermal cutting have a size distribution of less than 1 μm. The contaminated structures are able to generate radioactive aerosols in the decommissioning. Radioactive aerosols of 1 μm or less are deposited in the respiratory tract by workers’ breathing, causing the possibility of internal exposure. Therefore, workers must be protected from the risk of exposure to radioactive aerosols. Prior knowledge of aerosols generated during metal cutting is important to ensure worker safety. In this study, the physical and chemical properties of the aerosol were evaluated by measuring the number and mass concentrations of aerosols generated when cutting SUS304 and SA508 using the laser cutting method. High-resolution aerosol measuring equipment (HR-ELPI+, DEKATI) was used to measure the concentration of aerosols. The HR-ELPI+ is an impactor-type aerosol measuring equipment that measures the aerosol number concentration distribution in the aerodynamic diameter range of 6 nm to 10 um in real-time. And analyze the mass concentration of the aerosol according to the diameter range through the impactor. ICP-MS was used for elemental mass concentration analysis in the aerosol. Analytical elements were Fe, Cr, Ni and Mn. For the evaluation of physical and chemical properties, the MMAD of each element and CMAD were calculated in the aerosol distribution. Under the same cutting conditions, it was confirmed that the number concentration of aerosols generated from both materials had a uni-modal distribution with a peak around 0.1 um. CMAD was calculated to be 0.072 um for both SUS304 and SA508. The trend of the CMAD calculation results is the same even when the cutting conditions are changed. In the case of MMAD, it was confirmed that SUS304 had an MMAD of around 0.1 μm in size for only Fe, Cr and Mn. And SA508, Fe, Cr, Ni and Mn were all confirmed to have MMAD around 0.1 μm in size. The results of this study show that a lot of aerosols in the range of less than 1 μm, especially around 0.1 μm in size, are generated when metal is cut using laser cutting. Therefore, in order to protect the internal exposure of workers to laser metal cutting when decommissioning NPPs, it is necessary to protect from nano-sized aerosols beyond micron size.

The fuel fabrication facility has been built and is being operated by KAERI since licensing research reactor fuel fabrication in 2004. After almost 20 years of operation, outdated equipment for fabrication or inspection has been replaced by automated, digitalized ones to assure a higher quality of nuclear fuels. However, the generation of a large amount of radioactive waste is another concern for the replacement in terms of its volume and various types of it that should be categorized before disposal. The regulatory body, NSSC (Nuclear Safety and Security Commission) released a notice related to the classification of radioactive wastes, and most accessory equipment can be classified into the clearance levels, called self-disposal waste. In this study, the practice of self-disposal of metal radioactive waste is carried out to reduce its volume and downgrade its radioactivity. For metal radioactive waste, which is expected to occupy the most amount, analysis status and legal limitations were performed as follows: First, the disposal plan was established after an investigation of the use history for equipment. Second, those were classified by types of materials, and their surface radio-contamination was measured for checking self-disposable or not. After collecting data, the plan for the self-disposal was written and submitted to the Korea Institute of Nuclear Safety (KINS) for approval.

In order to dispose of spent nuclear fuel (SNF) in deep geological repository, source term evaluation considering its specification, enrichment, burnup, cooling time should be performed. In this study, the measured values of Takahama-3 pressurized water reactor SNF (WH 17×17) samples were analyzed with SCALE 6.1/ORIGEN-S and TRITON code calculation results for validation. Unlike the ORIGENS code, TRITON code calculations differed from two-dimensional neutron flux distribution by using the multi-group cross-section library. Both calculation results from ORIGEN-S and TRITON code showed higher errors in 234U, 239Pu, and 241Pu compared to other actinide nuclides. In the case of axial locations of fuel rods in fuel assembly, fuel rods located at the edge of the fuel assembly presented increased errors due to nuclear reaction cross-section. Overall, the ORIGEN-S predictions informed more accurate agreement with the measured results compared with TRITON results. Especially to 235U, 239Pu, and 240Pu radionuclides, ORIGEN-S errors were denoted more than twice as low as the TRITON results. Comparing the calculation results with experimental results implied that the ORIGENS code was more accurate code than the TRITON code for source term evaluation.

In biosphere assessment modeling for the safety assessment of the Wolsong LILW disposal facility, the multi-compartment modeling in which all radionuclides transport is described quantitatively in terms of transfer factors between various environmental compartments has been implemented. In order to reflect the actual transfer mechanisms of 14C in the environment the specific activity (SA) modeling approach can be applied as an alternative to the previous transfer factors (TF) approach. The assumption of full SA equilibrium throughout the terrestrial environment is completely satisfactory for 14C release to the atmosphere if the 12C is emitted as 14CO2. This is the only form that is readily taken up by plants, so that active carbon is incorporated into the plant via photosynthesis at the same rate as stable carbon. Accordingly, the 14C concentration in Bq/g stable carbon is the same in the plant as it is in the air. And animals take up carbon almost entirely through ingestion and the SA ratio in the plant is maintained in the animal. In this study, a specific activity model for 14C was implemented in a GoldSim biosphere assessment model. From the literature survey for existing specific activity models developed, the IAEA model was selected. The farming scenario utilizing well water was simulated and the resulting ingestion dose conversion factors (DCFs) from the IAEA SA model were compared with those of the TF approach. The parameter value for the concentration of stable carbon in the air (gC/m3) is used as 0.20 gC/m3 considering the Suess effect. The dose coefficient for food ingestion used for dose calculations was taken from ICRP-72 as 5.8E-10 Sv/Bq. It was found that the ingestion DCFs of the SA model showed about 3 times lower than those of the TF model in the farming scenario through irrigation of well water, so it is expected that the SA approach could be applied for a more realistic assessment. Though the comparisons were made on the results from the terrestrial ecosystem only in this study, it would be necessary to investigate the applicability of the SA modeling approach for 14C through extensive comparisons and analysis including an aquatic ecosystem, and through parameters survey suitable to the domestic condition.

Kori-1, the nuclear power plants in South Korea, first started operation in April 1978 and was suspended permanently in 2017. The saturation rate time of spent nuclear fuel generated by major nuclear power plants operating in Korea are getting closer. If we fail to dispose spent nuclear fuel, which is equivalent to high-level radioactive waste, the nuclear power plants will have to be shutdown. High-level radioactive waste is permanently disposed through a deep geological disposal system because it contains long-term half-life nuclides and emits high energy. To select the deep geological disposal site and construct the disposal facilities, it is necessary to establish appropriate regulatory policies accordingly. The status of database construction in OECD-NEA, NRC, SITEX, and IAEA, which provides safety regulations for deep geological disposal system, stipulates each requirement for dismantling nuclear power plants. However, details such as specific figures are not specified, and guidelines for the disposal of high-level radioactive wastes are not clearly distinguished. In Korea, the CYPRUS program, an integrated database system, has been developed to support comprehensive performance evaluation for high-level waste disposal. However, due to several difficult situations, maintenance and upgrades have not been performed, so the research results exist only in the form of raw data and the new research results have not been reflected. Other than that, there is no preemptive basis for regulating the deep geological disposal system. With real-time database, we can develop a regulatory system for the domestic deep disposal system by systematically analyzing the regulatory condition and regulatory case data of international organizations and foreign leading countries. The database system processed and stored primary data collected from nuclear safety reports and other related data. In addition, we used relational database and designed table to maximize time and space efficiency. It is provided in the form of a web service so that multiple users can easily find the data they want at the same time. Based on these technologies, this study established a database system by analyzing the legal systems, regulatory standards, and cases of major foreign leading countries such as Sweden, Finland, the United States, and Japan. This database aims to organize data for each safety case component and further prepare a safety regulatory framework for each stage of development of disposal facilities suitable for the domestic environment.