Transparent conductive tungsten (W) doped indium oxide (In2O3; IWO) films were deposited at different substrate bias voltage (-Vb) conditions at room temperature on glass substrates by radio frequency (RF) magnetron sputtering and the influence of the substrate bias voltage on the optical and electrical properties was investigated. As the substrate bias voltage increased to -350 Vb, the IWO films showed a lower resistivity of 2.06 × 10-4 Ωcm. The lowest resistivity observed for the film deposited at -350 Vb could be attributed to its higher mobility, of 31.8 cm2/Vs compared with that (6.2 cm2/Vs) of the films deposited without a substrate bias voltage (0 Vb). The highest visible transmittance of 84.1 % was also observed for the films deposited at the -350 Vb condition. The X-ray diffraction observation indicated the IWO films deposited without substrate bias voltage were amorphous phase without any diffraction peaks, while the films deposited with bias voltage were polycrystalline with a low In2O3 (222) diffraction peak and relatively high intensity (431) and (046) diffraction peaks. From the observed visible transmittance and electrical properties, it is concluded that the opto-electrical performance of the polycrystalline IWO film deposited by RF magnetron sputtering can be enhanced with effective substrate bias voltage conditions.

The aim of this study was to compare the concentrations of airborne pollutants (i.e., PMs, TVOC, and ozone) released from a laser printer with a new and/or a refilled toner cartridge. Also we compared the concentrations before and after attaching a HEPA filter at the outlet of exhausted air for each printer. PMs, TVOC, and ozone were released from all three different branded printers with both toner cartridges in accordance with their both a brand new and a used condition. For PMs, there were generally significant differences of concentrations between a brand new and used toner (p<0.05). Ozone level differences were found between a new and a refilled toner, but were not significant (p>0.05). For TVOC, there were significant differences of concentrations among brands, and toluene (3.46mg/m³) only was identified. The overall 70% of reduction for PMs’concentrations occurred after attaching a HEPA filter(p<0.05), and these results were pronounced for TSP. These results showed that similar levels of airborne pollutants were released from a laser printer with a new and a refilled toner cartridge. Also, these results indicate that the usage of a HEPA filter may be an effective method for reducing the released pollutants from a laser printer.

파우더 파운데이션은 사용이 간편하고 수정화장이 용이하여 고객들이 많이 사용하고 있으며, 파우더 파운데이션을 만드는 방법은 건식방식, 소성방식, 그리고 습식방법으로 크게 분류할 수가 있다. 이중 습식방법은 이미 잘 알려진 바와 같이 back injection 방법과 front injection 방법이 있으며, 본 논문에서는 front injection 방법을 사용해 실험을 진행하였다. 실험결과 용매의 종류에 따른 경도 변화를 살펴보면 휘발성 실리콘이나 탄화수소계 휘발성 물질을 이용할 때 보다 정제수를 이용할 때 경도가 높게 나타났으며, 사용감 측면에서는 물보다는 탄화수소계 휘발성 물질과 휘발성 실리콘 등을 사용했을 때, 고객 선호도가 높게 나타났다. 또한 코팅물질 변화에 따른 경도 변화로는 아미노산계 코팅물질을 사용하였을 대 경도가 상승하는 효과를 나타냈으며, 실리콘 코팅 물질을 사용했을 때 경도 상승효과가 미비한 것으로 나타났다. 이러한 결과를 토대로 각 대상 고객에 맞는 처방을 개발하고자 할 때 사용감과 경도의 상관관계를 알고, 처방설계에 이용한다면 고객이 원하는 사용감에 한발 더 접근할 수 있으리라 생각된다.

To improve coagulation characteristics and to reduce dossage of chemicals in watertreatment, polyaluminium sulfate was manufactured by reaction of polymerization between aluminium sulfate and sodium aluminate. As the results of affirmation and performance test, the yield of product was about 24% from molecular cut off levels by ultrafilteration method. The type of molecular is nearly affirmated as a kind of complex like Alm. (OH)n^(3m-n)+ from Scanning Electr Electron Mipy(S.E.M.) and X-ray diffraction test. Since the synthesized polymer was supposed to be quasi, further study for stabilization was required.