This study aims to present a performance based design for apartments through evacuation safety assessment and damage impact assessment due to acrylonitrile leakage. In the evacuation safety evaluation, ASET was analyzed as 25 min or more and 60 min or less when the ventilation rate was once per hour, and RSET was 22.6 min. Evacuation safety is satisfied when the number of ventilation per hour is less than 1, so it is necessary to design the number of ventilation to be 1 or less. In the damage impact assessment, the 0% structural collapse rate due to overpressure was measured to be between 71m and 90m, and the 0% fatality rate due to radiant heat was measured to be between 136m and 353m. Therefore, maintain a safe distance of 353m or more.

This study aims to present safety distances by the damage impact assessment of the leakage of propylene oxide. As a result of the experiment, the pressure 1psi range was 52m to 169m, the radiant heat 18kW/㎡ range was 63m to 163m, the AEGL-2 range was analyzed as 224m to 414m, and the fire ball diameter was analyzed to be 45m to 121m. Additionally, the extent of damages was proportional to the amount of propylene oxide stored or handled. The safe distance for a 10% lethality due to overpressure and radiant heat was calculated to be 134m, and the safe distance for a 0% lethality was 169m. Toxicity was measured at 134m with a lethality 0%. Therefore, the safety distance due to leakage of propylene oxide is calculated to be between 134m and 169m.

본 연구에서는 폴리술폰 분리막을 이용한 바이오가스 정제 공정으로 고선택성 소재를 이용한 2단 공정의 높은 회 수율 및 경제성과 동등한 수준의 회수율을 확보하기 위해 저온 고압의 분리막 공정을 설계하고 평가하였다. 폴리술폰 고분자 를 4성분계 도프를 이용하여 비용매 유도 상전이법으로 중공사 분리막을 제조하였다. 기체 분리용 중공사 분리막은 1.6 m2의 유효 막면적을 갖는 샘플을 제조하여 상온 및 저온에서 기체 투과 특성을 평가하였다. 제조된 기체분리막 모듈의 온도에 따 른 기체 투과 특성을 분석하기 위하여 온도별 단일 기체 투과도를 평가한 결과 이산화탄소와 메탄 투과도는 20°C에서 각각 412, 12.7 GPU이며, -20°C에서는 각각 280, 3.6 GPU로써 이상 선택도는 32.4에서 77.8로 향상되었다. 단일 기체 투과 테스 트 후 혼합 기체에 대한 분리 테스트를 진행하였으며, 모듈 1단 구성 및 2단 구성(막 면적비 1:1, 1:2, 1:3)을 통하여 투과 거 동을 살펴보았다. 1단 구성에서는 stage-cut이 상승함에 따라 메탄의 농도가 상승하지만, 반대로 회수율은 떨어지는 결과를 나 타내었다. 2단 구성 테스트에서는 메탄 농도 97% 기준에서 막 면적비 1:1보다 1:3이 메탄의 회수율이 더 높게 측정되었으며, 공급 기체의 온도가 낮을수록 메탄의 회수율이 높아짐을 확인하였고, 최종적으로 폴리술폰 2단 공정에서 메탄 농도 97%, 회 수율 97%의 결과를 달성하였다.

Looking at recent safety accidents in buildings, most of them due to lack of FM expertise, and this is due to human resources. In each all industry areas, some companies are competitive, representational, and leading in the market through long-term expertise and research in their respective fields. In the field of FM industry, some companies offer core-competencies in internal and external innovative building management through competition with others. However, old custom and old management form still exist in the FM field. However, an old custom and old management system still exist in the FM field; it forces cost-cutting and caused by carelessness in technical development competitiveness and safety measures. The government control by safety inspection and facility inspection through legislation of building management, but the management is still weak as a side of in the facility management section due to inspect sth as a mere formality and submit a paper report. These facts exist different kind of usage of the building have a three-party encounter between a building owner, user, and FM enterprises. In this research identify survey, especially building owner (manager)’s choice perception priority for optional factors to choose FM enterprises. Based on this, FM enterprises will be forced to seek a new dimension for better building management. In this light, the purpose of the research is to shape changes in the FM market culture safely and providing better service in building management and understanding building owner's insight through this research's information.

집박쥐 (Pipistrellus abramus)는 인간의 주거 지역을 중심으로 서식하는 대표적인 종으로, 우리나라에 광범위하게 분포하고 있다. 그러나 대부분의 박쥐류가 유사한 크기의 다른 포유동물보다 상대적으로 긴 수명을 가지는 것에 반하여 집박쥐는 매우 짧은 수명을 가지는 것으로 알려져 왔다. 지금까지 집박쥐의 장기 수명에 관한 내용으로는 암컷 5년, 수컷 3년의 확인 기록이 전부였다. 그러나 본 연구자들은 284개체에 대한 밴딩을 통하여 지금까지 알려진 집박쥐의 최대 수명보다 2배 이상 생존한 개체를 재포획 하였으며, 그 결과를 정리하였다. 집박쥐는 인간의 생활권과 가장 밀접한 종으로 서식지의 환경은 본 종의 수명에 직접적인 영향을 미친다고 볼 수 있다. 따라서 향후 서식지 환경에 따른 수명과의 연계성에 대한 연구가 이루어져야 할 것으로 판단되며, 본 자료는 집박쥐의 장기 생존과 수명에 관한 국내 첫 보고로써 향후 박쥐의 수명에 관한 기초 자료가 될 것으로 기대된다.

OBIGGS에서는 대기 중의 미량의 오존이 고분자 분리막의 손상을 가져오기 때문에 전단에 오존 제거장치를 설치하여 분리막에 전해지는 기체에서 오존의 농도를 감소시켜 분리막의 손상을 막고 있다. 본 연구에서는 OBIGGS용 기체 분리막을 이용하여 오존 노출시간에 따른 인장강도와 기체투과특성을 평가하여 오존 노출환경과 투과특성의 관계를 확인하였다. 폴리이미드계와 폴리설폰계 두 종류의 중공사 분리막을 이용하였고, 6.37 cm2의 유효 막 면적을 가지는 중공사 모듈을 제조하여 사용하였다. 오존 챔버를 이용하여 오존의 농도를 2-3 ppm으로 유지하였으며, 챔버 내의 기체를 펌프를 이용하여 모듈내로 지속적으로 공급하였으며, 오존 노출시간에 따라서 기체투과특성과 인장강도를 각각 평가하였다. 그 결과 폴리이미드계 중공사 분리막은 투과도에서 20%의 감소만 나타났을 뿐, 선택도와 인장강도에서 다른 큰 변화를 나타내지 않고 균일하게 유지되는 것을 확인하였다. 하지만 폴리설폰계 중공사 분리막을 사용하였을 때는 투과도가 80% 이상 감소하였고, 인장강도는 70% 이상 감소하는 결과를 나타내었다.

The general separation processes for liquid mixtures need the energy consumed and causes of primary cost. The pervaporation separation process could be regarded as the energy saving process[1]. In this study, it is introduced that the preferential isopropyl alcohol separation from the aqueous feed was carried out using the composite membranes according to the operating conditions, such as, the operating temperature, feed concentration etc. And the commercial scale module was prepared and tested for the long-term period, and finally the stabilized and consistent results of both permeability and selectivity were obtained.

Membrane-based gas separation process is one of the next generations’ gas separation processes for carbon capture and storage (CCS). Membrane process has the advantages of i) low energy consumption without a phase change during the separation, ii) small footprint and easy scale-up of membrane modules, and iii) clean process without any emission of harmful byproducts. The hollow fiber membranes used in this study shows CO2 permeance over 900 GPU (1 GPU = 10-6 cm³/cm²⋅sec⋅cmHg). Using the hollow fiber membranes and modules, we established a moveable CO2 separation system including pretreatment of flue gas and 3-stages of membrane cascade. The system was installed at the several on-site flue gas sources, and the performance of pilot plant operation will be presented in the presentation.

Numerical analysis was performed to evaluate for reinforcing performance of RC beams in flexure strengthened with Textile Reinforced Mortar (TRM) in this study. New bond strength model for TRM based on the model proposed by Teng et al. was suggested to predict the flexural behavior of RC beams and effective stress in accordance with debonding of TRM. And reduce factor of 0.729 was suggested by investigation of results on the bending test of RC beams strengthened with TRM. Reliability of proposed bond strength model was verified through the comparisons between collected test results and predicted results about the ultimate load of RC beams occurred by debonding of TRM. The ratios of predicted results on the total experimental results, the average and coefficient of variation were 1.00 and 0.094, respectively. Also, nonlinear analysis method proposed by Cho et al. was used to predict the displacement at the cross-section of mid-span for RC beams in flexure strengthened with TRM. At the three state of the RC beams such as occurrence of initial flexural crack in tensile concrete, yield of tensile rebar, and ultimate in accordance with debonding of TRM. Displacements of beams were calculated at the three state and load-displacement curves by predicted results were compared to the collected test results.

Membrane-based gas separation is one of the next generations’ gas separation technology for various gas and chemical industries (e.g. air separation, H2, CO2 separation, hydrocarbons, and fluorinated gas separation, etc). Membrane has the advantages of i) low energy consumption without a phase change during the separation, ii) small footprint and easy scale-up of membrane modules, and iii) clean process without any emission of harmful byproducts. Membrane materials are mostly composed of polymeric, inorganic and metallic materials whereas membrane modules are fabricates as flat-sheet, plate-and-frame, spiral-wound and hollow fibers. In this presentation, the evaluation method of membrane materials and modules for gas separation applications will be discussed.

Membrane-based gas separation is one of the next generations’ gas separation technology for carbon capture and storage (CCS). Membrane process has the advantages of i) low energy consumption without a phase change during the separation, ii) small footprint and easy scale-up of membrane modules, and iii) clean process without any emission of harmful byproducts. However, the requirement of CO2 separation membrane for CCS has limited the application of gas separation membranes in the industrial field. Here, we demonstrate the strategies to approach to the current limitation by developing a high flux of polymeric hollow fiber membrane. The membrane performance in this work is 900 GPU (1 GPU = 10-6 cm3/cm2‧sec‧cmHg) of CO2 permeance. The CO2 capture pilot plant using multi-stage membrane processes at KDHC has been on-site tested.

고분자 분리막을 이용한 이산화탄소 포집공정은 최근들어 분리막 소재기술의 발전과 함께 관심이 급격하게 높아지고 있다. 미국의 경우는 MTR사가 DOE의 지원을 받아 1MWe 규모의 발전소 배가스 중의 이산화탄소를 포집하는 실증연구를 진행하고 있다. 또한 유럽에서는 노르웨이의 NTNU가 미국 Airproducts사와 협력하여 시멘트제조공정에서 발생하는 이산화탄소를 포집하는 연구를 수행하는 중이다. 본 연구는 (주)에어레인이 미래부산하 KCRC 센터의 지원을 받아 50 Nm3/hr 규모의 배가스를 처리하는 단위 모듈을 이용하여 150 Nm3/hr 규모연소배가스 포집공정을 설계하는 과정을 언급하고자 한다. 또한 이 플랜트의 시운전 과정에서 얻어진 데이터와 공급기체중의 산소농도의 영향등이 다뤄질 것이다. 최종적인 주요결과는 CO2 회수율 93%, 회수농도 85%이었다.

The morphological characteristics of the baculum were compared among Rhinolophus ferrumequinum, Hypsugo alaschanicus, Vespertilio sinensis, and Murina hilgendorfi. Their bacula were located at the distal end but their shapes were differed among species. V. sinensis had the longest baculum (mean=7.27 mm), followed by R. ferrumequinum (mean=5.02 mm), H. alaschanicus (mean=2.60 mm) andM. hilgendorfi (mean=2.15 mm). The baculum of R. ferrumequinum was Y-shaped, with a pointed tip and that of V. sinensis was long and conical. However, the baculum of H. alaschanicus was I-shaped, with the widths of proximal and distal ends larger than that of the shaft. The baculum ofM. hilgendorfi was small, and oval shaped. The shaft of the baculum of R. ferrumequinum and H. alaschanicus was linear in shape, whereas that of V. sinensis was curved towards the distal end, and that ofM. hilgendorfi was bent upward. The results showed that the baculum morphology differed among these four species. These findings can be utilized as an identification key for these species, and they can be used as baseline data for studying the phyletic relationships of bats.

Flexural capacity of a Textile Reinforced Mortar(TRM) was investigated by an experimental study. The test program was accomplished on reinforced concrete(RC) slabs consisted of concrete(average compressive strength of 22.23 MPa) and rebar(strength class of SD400). RC slab had 450 mm and 150 mm in size and 2,600 mm in clear span. Strengthening was accomplished by applying carbon-fiber mesh in layers of mortar. Control slab(unstrengthened) and six slabs strengthened with TRM were fabricated to confirm the reinforcing performance in this study. Test variables considered amount of reinforcement and use of anchorage. As a results, it was validated that the flexural capacity of slabs strengthened with TRM increased from 159.9% to 285.2% according to the amount of TRM compared with unstrengthened slab. Experimental results indicated that there are increase in ductility as well as load carrying and deformation capacities when using multiple layers of textile.