삼불화알루미늄(AlF3)이 포함된 염화물-불화물 혼합 용융염에서 ZIRLO 튜브를 이용한 지르코늄 전해정련공정을 실증하였다. 순환 전압전류실험 결과, AlF3의 농도가 증가함에 따라 금속환원의 개시 전위가 일정하게 증가하고 지르코늄-알루미늄 합금형성과 관련된 추가적인 peak의 크기가 점차 증가하는 것으로 나타났다. 전류조절 전착법과 달리, −1.2 V의 일정전위 에서 수행한 지르코늄 전해정련에서 방사형 판 구조의 지르코늄 성장이 염의 상단 표면에서 확연하게 나타났으며, 전착물 지름의 크기는 AlF3의 농도에 따라 점차 증가하는 것으로 나타났다. 주사전자현미경(SEM)과 에너지 분산 X선 분광기(EDX) 와 X선 광전자 분광기(XPS)를 이용하여 판 구조의 지르코늄 전착물을 분석한 결과, 극미량의 알루미늄이 지르코늄-알루미늄 합금 형태로 존재하며, 전착물의 상단과 하단 간에 서로 다른 화학성분구조를 갖는 것으로 나타났다. AlF3의 첨가는 전착물 내 잔류염 양을 줄이고, 지르코늄 회수를 위한 전류효율을 향상시키는 데 효과적인 것으로 나타났다.

전극 구성에 따른 고효율 전해정련공정의 일반적인 모델을 구축하기 위하여, 상미분방정식 인터페이스를 갖는 COMSOL Multiphysics V5.3 전착 모듈을 사용하여 수치해석을 실시하였다. 구축된 모델은 한국원자력연구원에서 제작한 실험실 규 모 (1kg 우라늄/day 규모) 다중배열전극 전해정련장치를 사용해 전극 간 거리, 전극 배열을 변수로 하여 실시한 실험의 전 류밀도-전위 곡선과 비교하였다. 공정온도는 500℃이다. 용융염은 3wt% UCl3가 포함된 LiCl-KCl 공융염을 사용하였다. 검 증된 모델을 이용하여 전류밀도-셀전위 곡선을 계산한 결과 전극 간 거리가 가까울수록, 전극 배열은 양극/음극 면적비가 증 가할수록 셀 전위가 낮아져 전해정련장치의 우라늄 처리효율을 향상시킬 수 있다는 것을 확인하였다. 이러한 접근은 고출력 사용후핵연료 전해정련기의 안전설계를 위한 데이터베이스 구축에 유용할 것이다.

Zirconium(Zr) nuclear fuel cladding tubes are made using a three-time pilgering and annealing process. In order to remove the oxidized layer and impurities on the surface of the tube, a pickling process is required. Zr is dissolved in HF and HNO3 mixed acid during the process and pickling waste acid, including dissolved Zr, is totally discarded after being neutralized. In this study, the waste acid was recycled by adding BaF2, which reacted with the Zr ion involved in the waste acid; Ba2ZrF8 was subsequently precipitated due to its low solubility in water. It is very difficult to extract zirconium from the as-recovered Ba2ZrF8 because its melting temperature is 1031 oC. Hence, we tried to recover Zr using an electrowinning process with a low temperature molten salt compound that was fabricated by adding ZrF4 to Ba2ZrF8 to decrease the melting point. Change of the Zr redox potential was observed using cyclic voltammetry; the voltage change of the cell was observed by polarization and chronopotentiometry. The structure of the electrodeposited Zr was analyzed and the electrodeposition characteristics were also evaluated.

본 연구에서는 LNG-FPSO 선박에 탑재되어 있는 장비들의 운영효율을 최대화하기 위한 상태기반유지보수(CBM) 활동을 지원하는 보전시스템을 개발하였다. 개발된 보전시스템에서는 상태기반유지보수를 수행할 주요 장비들을 식별하여 이를 PWBS(Product Work Breakdown Structure)로 정의하였고 식별된 장비들로부터 실시간 수집되는 센서데이터를 이용하여 장비들의 고장분석과 최적 유지보수 방안을 결정하기 위한 경제성평가 등을 수행하며, 이들을 수행하기 위해 필요한 입출력 데이터를 저장, 관리하는 고장사례 및 유지보수데이터베이스를 구축하였다. 개발시스템의 성능검증을 현재 개발 중인 LNG-FPSO 선박의 Inlet 시스템의 Compressor와 화물창의 Pump Tower 등과 같은 주요 장비들을 대상으로 실시하였고 이를 바탕으로 상태기반유지보수의 가능성을 확인하였다.

To achieve the fabrication of high-quality Ag-coated Cu particles through a wet chemical process, we reported herein pretreatment conditions using an ammonium-based mixed solvent for the removal of a Cu2O layer on Cu particles that were oxidized in air for 1 hr at 200 oC or for 3 days at room temperature. Furthermore, we discussed the results of post-Ag plating with respect to removal level of the oxide layer. X-ray diffraction results revealed that the removal rate of the oxide layer is directly proportional to the concentration of the pretreatment solvent. With the results of Auger electron spectroscopy using oxidized Cu plates, the concentrations required to completely remove 50-nm-thick and 2-nm-thick oxides within 5 min were determined to be X2.5 and X0.13. However, the optimal concentrations in an actual Ag plating process using Cu powder increased to X0.4 and X0.5, respectively, because the oxidation in powder may be accelerated and the complete removal of oxide should be tuned to the thickest oxide layer among all the particles. Back-scattered electron images showed the formation of pure fine Ag particles instead of a uniform and smooth Ag coating in the Ag plating performed after incomplete removal of the oxide layer, indicating that the remaining oxide layer obstructs heterogeneous nucleation and plating by reduced Ag atoms.

Nd-Fe-B permanent magnets have been used in a wide variety of applications because of their high magnetic flux density. So, demand for neodymium has been increasing in worldwide. In this study, an electrowinning process was performed in LiF-NdF3-Nd2O3 high temperature molten salts. However, a corrosion resistant material for use in the molten salt must be found for stable operation because of the harsh corrosion environment of the electrowinning process. Therefore, for this paper, boron nitride(BN), aluminum nitride(AlN), and silicon nitride(Si3N4) were selected as protective and structural materials in the high temperature electrolyte. To investigate the characteristics of BN, AlN, and Si3N4, in molten salts, materials were immersed in the molten salts for 24, 72, 120, and 192 hours. Also, surface condition and stability were investigated by SEM and EDS and corrosion products were calculated by HSC chemistry. As a result, among BN, AlN, and Si3N4, AlN was found to show the best protective material properties.

The self-propagating high temperature synthesis approach was applied to synthesize amorphous boron nanopowders in argon atmospheres. For this purpose, we investigated the characteristics of a thermally induced combustion wave in the B2O3 + α Mg system(α = 1.0-8.0) in an argon atmospheres. In this study, the exothermic nature of the B2O3-Mg reaction was investigated using thermodynamic calculations. Experimental study was conducted based on the calculation data and the SHS products consisting of crystalline boron and other compounds were obtained starting with a different initial molar ratio of Mg. It was found that the B2O3 and Mg reaction system produced a high combustion temperature with a rapid combustion reaction. In order to regulate the combustion reaction, NaCl, Na2B4O7 and H3BO3 additives were investigated as diluents. In an experimental study, it was found that all diluents effectively stabilized the reaction regime. The final product of the B2O3 + α Mg system with 0.5 mole Na2B4O7 was identified to be amorphous boron nano-powders(< 100 nm).

The effects of Nb and Cr addition on the microstructure, corrosion and oxide characteristics of Zr based alloys wereinvestigated. The corrosion tests were performed in a pressurized water reactor simulated-loop system at 360oC. Themicrostructures were examined using OM and TEM, and the oxide properties were characterized by low-angle X-ray diffractionand TEM. The corrosion test results up to 360 days revealed that the corrosion rates were considerably affected by Cr contentbut not Nb content. The corrosion resistance of the Zr-xNb-0.1Sn-yCr quaternary alloys was improved by an increasing Nb/Cr ratio. The crystal structure of the precipitates was affected by a variation of the Nb/Cr ratio. The Zr-Nb beta-enrichedprecipitates were mainly formed in the high Nb/Cr ratio alloy while Zr(NbCr)2 precipitates were frequently observed in the lowNb/Cr ratio alloy. The studies of oxide characteristics revealed that the corrosion resistance was related to the crystal structureof the precipitate.

The production of nuclear fuel cladding tube is expected to increase with the nuclear power plant expansion. Zirconium(Zr) scrap that is generated during manufacturing is also expected to increase. Zr electrorefining experiment was carried out in the fluoride salt of LiF-KF-ZrF4 using multiple electrode for scale up and improving throughput Zr electrorefiner development. The Zr reduction peak observed at -0.8 V(vs.Ni). Polarization behavior showed that the amount of applied current increases because of decreasing cell resistance as the number of cathode increases. Experimental results showed the highest recovery rate about 98% at lowest current density of 25.64 mA/cm2 using 6 electrodes. XRD and TG analysis result show that pure Zr was recovered 99.92% and ICP analysis shows that lower impurity content than conventional impurity content of the Anode(97.8%). Electrorefining consumes energy about 7.15 kWh/kg less than 39.7% compared to the Kroll process using 6 electrode width of 20 mm and height of 65 mm. Because of increasing cell efficiency and recovery rate, using multiple cathode is determined as an efficient technique for scale up electrorefining Zr scrap.

To elucidate the effects of a pretreatment process on the uniformity of Ag electroless plating on Cu flakes, pretreatment time was mainly considered with a mixed solution of 0.15 M ammonium hydroxide and 0.0375 M ammonium sulphate. Optical inspection of Ag-coated Cu flakes determined that the optimal pretreatment time is 120 s. Repetition of the sequence in which Ag plating was done immediately after the pretreatment of 120 s clearly enhanced the plating uniformity. Scanning electron microscopy revealed that holes were formed irregularly on some Cu flakes during the period from the asdropping of an Ag precursor solution to 5 min. The hole formation was judged to be due to continuous removal of Cu on the local surfaces by the repetitive formation and elimination of Cu2O or Cu(OH)2 layers. However, the increase of the amount of Ag coating suppressed the hole creation and increasingly enhanced the antioxidant property.

To synthesize Sn nanoparticles (NPs) less than 30 nm in diameter, a modified polyol process was conducted at room temperature using a reducing agent, and the effects of different pH values of the initial solutions on the morphology and size of the synthesized Sn NPs were analyzed. tin(II) 2-ethylhexanoate, diethylene glycol, sodium borohydride, polyvinyl pyrrolidone (PVP), and sodium hydroxide were used as a precursor, reaction medium, reducing agent, capping agent, and pH adjusting agent, respectively. It was found by transmission electron microscopy that the morphology of the synthesized Sn NPs varied according to the pH of the initial solution. Moreover, while the size decreased to 11.32 nm with an increase up to 11.66 of the pH value, the size increased rapidly to 39.25 nm with an increase to 12.69. The pH increase up to 11.66 dominantly promoted generation of electrons and increased the amount of initial nucleation in the solution, finally inducing the reduced-size of the Sn particles. However, the additional increase of pH dominantly induced a decrease of PVP by neutralization, which resulted in acceleration of the agglomeration by collisions between particles.

용융염 전해정련공정은 사용후핵연료로부터 전기화학적인 방법을 통해 음극에서 우라늄을 회수 하는 공정이다. 이 때 우라 늄은 약 30wt%의 염을 포함하고 있어 순수한 우라늄을 얻기 위해서는 염을 제거하는 Cathode Process (CP)가 필수적이다. CP는 대량의 우라늄을 처리해야 하므로 파이로공정의 난관중의 하나로 인식되고 있으며, 우라늄의 순도가 최종적으로 결정 되는 단계이므로 매우 중요한 공정이다. 현재, 이에 대한 연구는 주로 실험적 방법에 근거 하고 있어 염 제거 공정 중 온도, 압력, 염 가스의 거동을 관찰하기 어렵다. 따라서 본 연구에서는, 공정의 운전 조건에 대해 적합한 수학적 모델을 이용하여 전산모사 해석을 진행하였다. 본 연구는 증류부에서 염 가스의 증류 량, 확산계수에 의해 계산된 장치 내 염 가스의 이동 그 리고 응축부에서의 응결속도를 중점적으로 연구하였다. 장치내의 각각의 염 가스 거동을 정의하기 위해 Hertz-Langmuir 관 계식, Chapman-Enskog Theory, ANSYS-CFX의 상용 코드를 사용하였다. 그리고 HSC Chemistry에서 염의 물성 값을 이용 하여 모델을 구성하였다. 본 연구의 전산모사 해석을 통해 얻은 연구 결과를 이용하여 염 가스의 거동과 장치의 최적 운전 조건을 예측하였다. 따라서 본 해석 결과는 CP의 물리적 현상을 깊게 이해하는데 쓰일 뿐 아니라, 공학규모의 CP 장치를 상 용규모로 확장하는데 이용 할 수 있다.

이 연구는 자돈의 분변에서 분리된 Enterococcus faecim 193이 생산한 박테리오신을 부분정제하고 그 특성을 파악하여 천연 식품보존제 또는 첨가제로서의 이용가능성을 알아보고자 실시되었다. Enterococcus faecium 193의 배양시간에 따른 항균활성을 측정한 결과 항균활성은 3시간째부터 나타나기 시작하여 12시간째에 1280 AU/ml로 최대 활성을 나타내었다. Enterocin 193은 단백질 분해효소(trypsin, pepsin, 및 proteinase K)의 처리에 의해 항균활성이 소실되었으나 넓은 범위의 pH (1-11)와 열처리(121℃, 15분)에 비교적 안정하였다. 또한 50% 농도의 acetone, acetonitrile, chloroform 및 ethanol 등 유기용매에 안정하였으나, 50% methanol을 처리할 경우 항균활성이 50% 감소하였다. 이 박테리오신은 황산암모늄 침전, 소수성 크로마토그래피와 젤 여과 크로마토그래피에 의해 정제되었고 specific activity는 14.8배 증가하였다. SDS-PAGE에 의해 측정한 이 단백질의 분자량은 약 5 kDa이었다.

Synthesis of sub-micron 2SnO·(H2O) powders by chemical reduction process was performed at room temperature as function of viscosity of methanol solution and molecular weight of PVP (polyvinylpyrrolidone). Tin(II) 2-ethylhexanoate and sodium borohydride were used as the tin precursor and the reducing agent, respectively. Simultaneous calcination and sintering processes were additionally performed by heating the 2SnO·(H2O) powders. In the synthesis of the 2SnO·(H2O) powders, it was possible to control the powder size using different combinations of the methanol solution viscosity and the PVP molecular weight. The molecular weight of PVP particularly influenced the size of the synthesized 2SnO·(H2O) powders. A holding time of 1 hr in air at 500˚C sufficiently transformed the 2SnO·(H2O) into SnO2 phase; however, most of the PVP (molecular weight: 1,300,000) surface-capped powders decomposed and was removed after heating for 1 h at 700˚C. Hence, heating for 1 h at 500˚C made a porous SnO2 film containing residual PVP, whereas dense SnO2 films with no significant amount of PVP formed after heating for 1 h at 700˚C.

핵연료는 원자로 운전 중 예기치 못한 상황에서 연료 결함을 초래할 수 있다. 핵연료 결함은 연료봉의 수소화나 이물질에 의한 금속 마모, 그리고 펠렛과 피복관의 상호작용에 의해 피복관이 손상된다. 이렇게 손상된 핵연료의 결함원인을 규명하는 것은 원자력발전의 안전운전에 중요하다고 사료된다. 핵연료가 손상되면 원자로 냉각재가 오염되어 원자로 출력을 낮추거나, 발전소를 정지할 수도 있다. 모든 사용후연료는 건식저장고로 이동 보관되어야 하나, 결함연료는 이동할 수 없으므로 이 연구의 목적은 중수로형 원자로에서 연료가 인출된 후 사용후연료 저장조에서 보관된 연료에 대하여 결함 여부를 판단할 수 있 는 기술을 개발하고자 하였다. 이 연구를 통하여 핵종 누설 검출 기술을 이용한 사용후연료 검사기술을 개발하였으며, 이 기술을 월성발전소에 적용함으로써, 검사기술 및 검사시스템에 대한 성능을 입증하였다.

경제적이고 우수한 핵확산저항성을 갖는 파이로공정의 핵심 단위공정인 전해제련 공정에서 U와 TRU를 동시에 회수하기 위해 환원전극으로써 LCC가 사용된다. 한가지 원소만을 회수하는 금속음극과는 달리 LCC는 전기화학적으로 U와 TRU의 선택적 분리가 어려워 핵확산저항성을 높이는 기술의 핵심이라고 할 수 있다. LCC를 담아놓는 LCC 도가니는 U나 TRU로만 전착되어야하기 때문에 도가니는 전기적으로 절연되어야 한다. LCC와의 안정성과 회수된 TRU 및 용융염과의 화학적 안전성은 물론 공정 중 전착될 수 있는 금속 Li과의 반응성도 고려되어야하므로 LCC 도가니의 소재 특성은 매우 중요하다. 본 연구에서는 Al2O3, MgO, Y2O3, BeO 네 가지 대체 세라믹 소재의 화학적 안정성을 500℃에서 모의 LCC로 열역학적 및 실험적으로 평가하였다. 세라믹 기판 위의 LCC 접촉각은 화학적 반응성을 예측하기 위해 시간에 따라 측정하였다. Al2O3는 가장 낮은 화학적 안정성 갖고 BeO는 재료 내에 존재하는 기공은 접촉각감소에 영향을 주었다. MgO, Y2O3는 우수한 화학적 안정성을 나타내었다.

Sulgidduk is a kind of basic steamed rice cake in Korea. Multifunctional portable grinder was used for making sulgidduk and investigated the characteristic changes of rice powder for deciding the proper particle size of rice powder. Operation times for grinding the water absorbed swelled rice were 10, 20, 30 and 40 seconds. Moisture contents of rice powder and sulgidduk showed an increasing tendency with an increase of operation times for grinding. Springiness showed significant differences according to the operation times. Cohesiveness was decreased severely after 40 seconds grinding. Chewiness showed high after 20 seconds grinding in all groups; however, decreased after 40 seconds grinding and showed similar chewiness of the control group. Fracturability also showed severe increased tendency after 20 seconds grinding and decreased after 30 seconds grinding. Strength and hardness showed significant differences; they were increased until 30 seconds and severely decreased after 40 seconds grinding. L values showed significant differences in all the groups (p≤0.05). The a and b values did not show any differences in all groups. Overall sensory evaluations, such as colors, flavors and texture, were increased with operation times for grinding and showed significant differences among the groups (p<0.05). As a result of this study, 40 seconds grinding times were the best condition for making sulgidduk, using by multifunctional grinder.