Hydraulic conductivity is a critical design parameter for buffers in high-level radioactive waste repositories. Most employed prediction models for hydraulic conductivity are limited to various types of bentonites, the main material of the buffer, and the associated temperature conditions. This study proposes the utilization of a novel integrated prediction model. The model is derived through theoretical and regression analyses and is applied to all types of compacted bentonites when the relationship between hydraulic conductivity and dry density for each compacted bentonite is known. The proposed model incorporates parameters such as permeability ratio, dynamic viscosity, and temperature coefficient to enable accurate prediction of hydraulic conductivity with temperature. Based on the results obtained, the values are in good agreement with the measured values for the selected bentonites, demonstrating the effectiveness of the proposed model. These results contribute to the analysis of the hydraulic behavior of the buffer with temperature during periods of high-level radioactive waste deposition.

The bentonite buffer material is a crucial component in an engineered barrier system used for the disposal of high-level radioactive waste. Because a large amount of heat from the disposal canister is released into the bentonite buffer material, the thermal conductivity of the bentonite buffer is a crucial parameter that determines the design temperature. At the Korea Atomic Energy Research Institute (KAERI), a new standard bentonite (Bentonil-WRK) has been used since 2022 because Gyeongju (KJ) bentonite is no longer produced. However, the currently available data are insufficient, making it essential to investigate both the basic and complex properties of Bentonil-WRK. Thus, this study evaluated its geotechnical and thermal properties and developed a thermal conductivity empirical model that considers its dry density, water content, and temperature variations from room temperature to 90°C. The coefficient of determination (R2) for the model was found to be 0.986. The thermal conductivity values of Bentonil-WRK were 1–10% lower than those of KJ bentonite and 10–40% higher than those of MX-80 bentonites, which were attributable to mineral-composition differences. The thermal conductivity of Bentonil-WRK ranged between 0.504 and 1.149 W·(m−1·K−1), while the specific heat capacity varied from 0.826 to 1.138 (kJ·(kg−1·K−1)).

The bentonite buffer material is a crucial component for disposing of high-level radioactive waste (HLW). Several additives have been proposed to enhance the performance of bentonite buffer materials. In this study, unconfined compression tests were conducted on bentonite mixtures as well as pure bentonite buffer material. Joomunjin and silica sands were added at a 30% ratio, and graphite was added at 3% along with bentonite. The unconfined compression strength (UCS) and elastic modulus of pure bentonite were found to be 20% to 50% higher than those of bentonite mixtures under similar dry density and water content conditions. This decrease in strength can be attributed to the reduced cross-sectional area available for bearing the applied load in the bentonitemixture. Furthermore, the 3% graphite-bentonite mixture exhibited a 10% to 30% higher UCS and elastic modulus compared to the 30% sand-bentonite mixtures. However, since the strength properties of additive-bentonite mixtures are lower than those of pure bentonite, it is essential to evaluate thermohydraulic-mechanical functional criteria when considering the use of bentonite mixtures as buffer materials.

In environments where buffer materials are exposed to increased temperature due to the decay heat emitted by radioactive waste, it is crucial to assess the performance of the buffer material in relation to temperature effects. In this study, we conducted experiments using Bentonil-WRK, a calcium-type bentonite, compacted to a dry density of 1.65 g/cm3 and an initial water content of 15%. The experimental temperature conditions were set to 30, 60, 90, 110, and 130°C. We observed that the swelling pressure of the compacted bentonite buffer decreased as the temperature increased. The findings from this study can provide valuable guidance for the design of high-level waste repository in Korea.

In the design of HLW repositories, it is important to confirm the performance and safety of buffer materials at high temperatures. Most existing models for predicting hydraulic conductivity of bentonite buffer materials have been derived using the results of tests conducted below 100°C. However, they cannot be applied to temperatures above 100°C. This study suggests a prediction model for the hydraulic conductivity of bentonite buffer materials, valid at temperatures between 100°C and 125°C, based on different test results and values reported in literature. Among several factors, dry density and temperature were the most relevant to hydraulic conductivity and were used as important independent variables for the prediction model. The effect of temperature, which positively correlates with hydraulic conductivity, was greater than that of dry density, which negatively correlates with hydraulic conductivity. Finally, to enhance the prediction accuracy, a new parameter reflecting the effect of dry density and temperature was proposed and included in the final prediction model. Compared to the existing model, the predicted result of the final suggested model was closer to the measured values.

In order to reduce the area of the high-level radioactive waste (HLW) repository, a buffer material with high thermal conductivity is required. This is because if the thermal conductivity of the buffer material is high, the distance between the disposal tunnels and the deposition holes can be reduced. Sand, which is a natural material and has higher thermal conductivity than bentonite, is added to bentonite to develop an enhanced buffer material. For the sand-bentonite mixture, it is important which sand to use and how much to add because an enhanced buffer material should satisfy both hydraulic (H) and mechanical (M) performance criteria while improving thermal conductivity (T). In this study, we would like to show what type of sand and how much sand should be added to develop an enhanced buffer material by adding sand to Gyeongju bentonite, a representative bentonite in Korea. For this purpose, the thermal conductivity, hydraulic conductivity, and swelling pressure of the sand-Gyeongju bentonite mixture according to the sand addition rate were measured. It is more efficient to use silica sand with smaller particles than Jumunjin sand which is a representative sand in Korea as an additive for an enhanced buffer material than using the Jumunjin sand. In order for the sand-Gyeongju bentonite buffer material to satisfy both the hydraulic and mechanical performance criteria as a buffer material while increasing the thermal conductivity, it is judged that the optimum dry density is 1.7 g/cm3 at least and the optimum sand addition rate is 10% at most.

The buffer block, which is one of the main components of the engineering barrier system, plays an essential role in mitigating groundwater infiltration and radionuclide transport in a high-level nuclear waste repository. To achieve those purposes, the compacted buffer block must satisfy the functional safety criteria for dry density, water content, and many other components. In this study, the compation curves of the compacted bentonite-sand mixtures were evaluated to identify the relationship between the dry density and the water content of the buffer material. The floating die press at 10 MPa and the cold isostatic press at 40 MPa were applied to compaction of a buffer block with a diameter of 100 mm and a thickness of 10 mm. The condition of a bentonite-sand mixing ratio was 6:4, 7:3, 8:2, and 9:1 with 9 to 21% water content. As a result, the maximum dry density increases, the optimum moisture content decreases as the sand content of buffer material increases. This study can provide the conditions for manufacturing the compacted bentonite-sand buffer block.

The buffer material plays a role in preventing the excessive rise in temperature generated from the high-level radioactive waste by dissipating the decay heat to the rock. For this reason, the buffer material must have thermal properties to ensure the performance of the deep geological repository. This study measured the thermal conductivity of sand-bentonite according to the mixing ratio to improve the thermal properties. The compacted buffer was manufactured with a sand-bentonite mixing ratio of 6:4, 7:3, and 8:2 with 9 to 12% water content. As a result, the thermal conductivity increases as the ratio of sand increases. As a further study, it is necessary to experiment on whether sand-bentonite’s hydraulic, mechanical, and chemical performance is suitable for the stable operation of a repository.

Increasing thermal conductivity of buffer materials makes the disposal tunnel and hole spacings in high-level radioactive waste (HLW) repositories decrease, so that the area of the HLW repository decreases, which gives more choices to choose the HLW repository site and economical cost savings to construct HLW repositories. Thus, developing enhanced buffer materials with improved thermal conductivity is needed. One of the methods to develop enhanced buffer materials is to add additives to the bentonite which is main material for buffer materials. Most additives have high thermal conductivity, but most additives do not swell or less swell than bentonite, so that the swelling pressure of the enhanced buffer materials by additives decreases compared to the swelling pressure of pure bentonite buffer materials. Swelling pressure is an important performance criterion to design buffer materials. Thus, it is important to confirm the swelling pressure of the enhanced bentonite. However, it is not simple to measure the swelling pressure of the buffer materials and furthermore, it takes several days to measure the swelling pressure of the buffer materials. For these reasons, swelling index can be considered to predict the swelling pressure of the enhanced buffer materials relatively. In this study, it was investigated through tests how the swelling index of bentonite-sand mixtures change according to the amount of sand and it was found that the linear relationship between swelling index and sand amount in the bentonite-sand mixtures.

A geological repository system consists of a disposal canister with packed spent fuel, buffer material, backfill material, and intact rock. Among these, the bentonite buffer is one of the most important components to assure the safe disposal of high-level radioactive waste (HLW). As the bentonite buffer is installed as a block type, it is important to fabricate homogeneously. Generally, floating die method and cold isostatic press (CIP) method are used to fabricate bentonite blocks. In this paper, two bentonite blocks were produced using float die method at first, and CIP method was additionally applied to just one block. After that, several samples were cored from two blocks. The dry density and water content of several samples produced from two blocks were measured.

Extensive studies have been conducted on thermal conductivity of bentonite buffer materials, as it affects the safety performance of barriers engineered to contain high-level radioactive waste. Bentonite is composed of several minerals, and studies have shown that the difference in the thermal conductivity of bentonites is due to the variation in their mineral composition. However, the specific reasons contributing to the difference, especially with regard to the thermal conductivity of bentonites with similar mineral composition, have not been elucidated. Therefore, in this study, bentonites with significantly different thermal conductivities, but of similar mineral compositions, are investigated. Most bentonites contain more than 60% of montmorillonite. Therefore, it is believed that the exchangeable cations of montmorillonite could affect the thermal conductivity of bentonites. The effect of bentonite type was comparatively analyzed and was verified through the effective medium model for thermal conductivity. Our results show that Ca-type bentonites have a higher thermal conductivity than Na-type bentonites.

In this paper, a local deformation effect in thin-walled box beams is investigated via a finite element modal analysis. The analysis is carried out for single-cell and multi-cell box beam configurations. The single-cell box beam with and without a neck, which mimics a simple wind-turbine blade, is analyzed first. The results obtained by shell elements are compared to those of one-dimensional(1D) beam elements. It is observed that the wall thickness plays a crucial role in the natural frequencies of the beam. The 1D beam analysis deviates from the shell analysis when the wall thickness is either thin or thick. The shell modes(local deformations) are dominant as it becomes thin, whereas the shear deformation effects are significant as it does thick. The analysis is extended to the single-cell box beam with a neck, in which the shell modes are confined to near the neck. Finally the multi-cell box beam with a taper, which is quite similar to real wind-turbine blade configuration, is considered to investigate the local deformation effect. The results reveal that the 1D beam analysis cannot match with the shell analysis due to the local deformation, especially for the lagwise frequencies. There are approximately 5∼7% errors even if the number of segments is increased.