The bentonite buffer material is a crucial component in an engineered barrier system used for the disposal of high-level radioactive waste. Because a large amount of heat from the disposal canister is released into the bentonite buffer material, the thermal conductivity of the bentonite buffer is a crucial parameter that determines the design temperature. At the Korea Atomic Energy Research Institute (KAERI), a new standard bentonite (Bentonil-WRK) has been used since 2022 because Gyeongju (KJ) bentonite is no longer produced. However, the currently available data are insufficient, making it essential to investigate both the basic and complex properties of Bentonil-WRK. Thus, this study evaluated its geotechnical and thermal properties and developed a thermal conductivity empirical model that considers its dry density, water content, and temperature variations from room temperature to 90°C. The coefficient of determination (R2) for the model was found to be 0.986. The thermal conductivity values of Bentonil-WRK were 1–10% lower than those of KJ bentonite and 10–40% higher than those of MX-80 bentonites, which were attributable to mineral-composition differences. The thermal conductivity of Bentonil-WRK ranged between 0.504 and 1.149 W·(m−1·K−1), while the specific heat capacity varied from 0.826 to 1.138 (kJ·(kg−1·K−1)).

High level radioactive waste (HLW) final disposal repository is faced thermos-hydro-mechanical - radioactive condition because it is placed over 500 m in depth and waste emits decay heats for decades. Repository will be operated around 100 years and will be closed after all the wastes are disposed. The integrity of engineered barriers including buffer, backfill, concrete plug and canister and natural barrier (natural rock mass) will be stood during operating periods. Monitoring sensors for concrete and rock mass is conducted using piezo based sensors such as accelerometer or acoustic emission (AE) sensors. Typical accelerometer for harsh conditions is commonly expensive and data/power cable can be a potential groundwater inflow and nuclide outflow path. The fiber optic accelerometer whose data and power cable are united and has limited volume. Therefore, it can be a potential alternative sensor of piezo based sensors. The temperature limits and accelerated tests for fiber optic sensors are conducted. Most of sensors gives a malfunction around 130°C. The results of these experimental tests give a possibility of communications in compacted bentonite buffer and will be utilized for the design of monitoring systems for the repository.

The occurrence of shear failure in a rock mass, resulting from the sliding of joint surfaces, is primarily influenced by the surface roughness and contact area of these joints. Furthermore, since joints serve as crucial conduits for the movement of water, oil, gas, and thermal energy, the aperture and geometric complexity of these joints have a significant impact on the hydraulic properties of the rock mass. This renders them critical factors in related industries. Therefore, to gain insights into the mechanical and hydraulic behavior of a rock mass, it is essential to identify the key morphological characteristics of the joints mentioned above. In this study, we quantified the morphological characteristics of tensile fractures in granitic rocks using X-ray CT imaging. To accomplish this, we prepared a cylindrical sample of Hwang-Deung granite and conducted splitting tests to artificially create tensile fractures that closely resemble rough joint surfaces. Subsequently, we obtained 2D sliced X-ray CT images of the fractured sample with a pixel resolution of approximately 0.06 mm. By analyzing the differences in CT numbers of the rock components (e.g., fractures, voids, and rock matrix), we isolated and reconstructed the geometric information of the tensile fracture in three dimensions. Finally, we derived morphological characteristics, including surface roughness, contact area, aperture, and fracture volume, from the reconstructed fracture.

Engineered Barrier Systems (EBS) are a key element of deep geological repositories (DGR) and play an important role in safely isolating radioactive materials from the ecosystem. In the environment of a DGR, gases can be generated due to several factors, including canister corrosion. If the gas production rate exceeds the diffusion rate, pore pressures may increase, potentially inducing structural deterioration that impairs the function of the buffer material. Therefore, understanding the hydraulic-mechanical behavior of EBS due to gas generation is essential for evaluating the longterm stability of DGR. This study employed X-ray computed tomography (CT) technology to observe cracks created inside the buffer material after laboratory-scale gas injection experiments. After CT scanning, we identified cracks more clearly using an image analysis method based on machine learning techniques, enabling us to examine internal crack patterns caused by gas injection. In the samples observed in this study, no cracks were observed penetrating the entire buffer block, and it was confirmed that most cracks were created through the radial surface of the block. This is similar to the results observed in the LASGIT field experiment in which the paths of the gas migration were observed through the interface between the container and the buffer material. This study confirmed the applicability of high-resolution X-ray CT imaging and image analysis techniques for qualitative analysis of internal crack patterns and cracks generated by gas breakthrough phenomena. This is expected to be used as basic data and crack analysis techniques in future research to understand gas migration in the buffer material.

The operation time of a disposal repository is generally more than one hundred years except for the institutional control phase. The structural integrity of a repository can be regarded as one of the most important research issues from the perspective of a long-term performance assessment, which is closely related to the public acceptance with regard to the nuclear safety. The objective of this study is to suggest the methodology for quantitative evaluation of structural integrity in a nuclear waste repository based on the adaptive artificial intelligence (AI), fractal theory, and acoustic emission (AE) monitoring. Here, adaptive AI means that the advanced AI model trained additionally based on the expert’s decision, engineering & field scale tests, numerical studies etc. in addition to the lab. test. In the process of a methodology development, AE source location, wave attenuation, the maximum AE energy and crack type classification were subsequently studied from the various lab. tests and Mazars damage model. The developed methodology for structural integrity was also applied to engineering scale concrete block (1.3 m × 1.3 m × 1.3 m) by artificial crack generation using a plate jacking method (up to 30 MPa) in KURT (KAERI Underground Research Tunnel). The concrete recipe used in engineering scale test was same as that of Gyeongju low & intermediate level waste repository. From this study, the reliability for AE crack source location, crack type classification, and damage assessment increased and all the processes for the technology development were verified from the Korea Testing Laboratory (KTL) in 2022.

The buffer is installed around the disposal canister, subjected to heating due to decay heat while simultaneously experiencing expansion influenced by groundwater inflow from the surrounding rock. The engineering barrier system for deep geological disposal require the evaluation of longterm evolution based on the verification of individual component performance and the interactions among components within the disposal environment. Thus, it is crucial to identify the thermalhydro- mechanical-chemical (THMC) processes of the buffer and assess its long- and short-term stability based on these interactions. Therefore, we conducted experimental evaluations of saturationswelling, dry heating, gas transport, and mineralogical alterations that the buffer may undergo in the heated-hydration environment. We simulated a 310 mm-thick buffer material in a cylindrical form, simulating the domestic disposal system concept of KRS+ (the improved KAERI reference disposal system for spent nuclear fuel), and subjected it to the disposal environment using heating cartridges and a hydration system. To monitor the thermal-hydro-mechanical behavior within the buffer material, load cells were installed in the hydration section, and both of thermal couples and relative humidity sensors were placed at regular intervals from the heat source. After 140 days of heating and hydration, we dismantled the experimental cell and conducted post-mortem analyses of the samples. In this post-mortem analysis, we performed functions of distance from the water contents, heat source, wet density, dry density, saturation, and X-Ray diffraction analysis (XRD). The results showed that after 140 days in the heated-hydration environment, the samples exhibited a significant decrease water contents and saturation near the heat source, along with very low wet and dry densities. XRD Quantitative Analysis did not indicate mineralogical changes. The findings from this study are expected to be useful for input parameters and THMC interaction assessments for the long-term stability evaluation of buffer in deep geological disposal.

Rock discontinuities in underground rock behave as weak planes and affect the safety of underground structures, such as high-level radioactive waste disposal and underground research facilities. In particular, rock discontinuities can be a main flow path of groundwater and induce large deformation caused by stress disturbance or earthquakes. Therefore, it is essential to investigate the characteristics of rock discontinuities considering in-situ conditions when constructing highlevel radioactive waste disposal, which needs to assure the long-term safety of the structure. We prepared Hwang-Deung granite rock block specimens, including a saw-cut rock surface, to perform multi-stage direct shear tests as a preliminary study. In the multi-stage direct shear tests, we can exclude possible errors induced by different specimens for obtaining a full failure envelope by using an identical specimen. We applied the initial normal stress of 3 MPa on the specimen and increased the normal stress to 5 and 10 MPa step by step after peak shear stress observation. We obtained the mechanical properties of saw-cut rock surfaces from the experiments, including friction coefficient and cohesion. Additionally, we investigated the effect of filling material between rock discontinuities, assuming the erosion and piping phenomenon in the buffer material of the engineering barrier system. When the filling material existed in the rock surfaces, the shear characteristics deteriorated, and the effect of bentonite was dominant on the shear behavior.

The engineered barrier system (EBS), composed of spent nuclear fuel, canister, buffer and backfill material, and near-field rock, plays a crucial role in the deep geological repository for high-level radioactive waste. Understanding the interactions between components in a thermo-hydro-mechanical -chemical (THMC) environment is necessary for ensuring the long-term performance of a disposal facility. Alongside the research project at KAERI, a comprehensive experimental facility has been established to elucidate the comprehensive performance of EBS components. The EBS performance demonstration laboratory, which installed in a 1,000 m2, consists of nine experimental modules pertaining to rock mechanics, gas migration, THMC characteristics, buffer-rock interaction, buffer & backfill development, canister corrosion, canister welding, canister performance, and structure monitoring & diagnostics. This facility is still conducting research on the engineering properties and complex interactions of EBS components under coupled THMC condition. It is expected to serve as an important laboratory for the development of the key technologies for assessing the long-term stability of engineered barriers

Due to the necessity of isolating spent nuclear fuel (SNF) from the human life zone for a minimum of 106 years, deep geological disposal (DGD) has emerged as a prominent solution for SNF management in numerous countries. Consequently, the resilience of disposal canisters to corrosion over such an extended storage period becomes paramount. While copper exhibits a relatively low corrosion rate, typically measured in millimeters per million years, in geological environment, special attention must be directed towards verifying the corrosion resistance of copper canister welds. This validation becomes inevitable during the sealing of the disposal canister once SNFs are loaded, primarily because the weld zone presents a discontinuous microstructure, which can accelerate both uniform and localized corrosion processes. In this research, we conducted an in-depth analysis of the microstructural characteristics of copper welds manufactured by TIG-based wire are additive manufacturing, which is ideal for welding relatively large structures such as a disposal canister. To simulate the welds of copper canister, a 12 mm thick oxygen-free plate was prepared and Y and V grooves were applied to perform overlay welding. Both copper welding zones were very uniform, with negligible defects (i.e., void and cracks), and contained relatively large grains with columnar structure regardless of groove types. For improving microstructures at welds with better corrosion resistance, the effect of preheat temperature also investigated up to 600°C.

The Barcelona Basic Model (BBM) is an elasto-plastic model used to describe the coupled thermo-hydro-mechanical behaviors of unsaturated soil. BBM is frequently adopted to model the unique swelling behavior of bentonite, which is generally considered as the buffer material between the host rock and the canister containing high-level radioactive waste in deep geological repositories, under the changing thermal, hydraulic, mechanical and chemical conditions during the lifetime of repository. Therefore, a variety of the continuum-based numerical methods tried to add the BBM for modelling the multi barrier systems of geological repository and succeeded to describe the elasto-plastic deformation of bentonite. However, to demonstrate the entire barrier systems the host rock should be modelled simultaneously with the buffer materials, and the continuum-based methods may be limited in their ability to reflect the fracture networks in the host rock which could be the major flow channels of groundwater. This research applies BBM in 3DEC, a three-dimensional block-based discrete element method, and validates the model by comparing the change of specific volume and mean effective stress during three numerical test cases. Discontinuum-based numerical methods with BBM can be extended to describe the coupled thermo-hydro-mechanical processes of multi-barrier systems in geological repositories, with a focus on the interaction between the host rock and bentonite.

The natural barrier system surrounding the geological repository for high-level radioactive waste plays a crucial role in preventing or delaying the leakage of radionuclides. Therefore, the natural barrier should ensure low permeability to prevent groundwater flow into the engineered barrier system throughout the repository’s lifetime. Crystalline rock, considered as the host rock for the geological repository in Korea, exhibits low intact rock permeability, but the crystalline rock often contains the multiple discontinuities due to its high brittleness that can allow the unexpected fluid flow. Therefore, the long-term hydraulic behavior of the discontinuity should be characterized while considering additional thermal, mechanical, and chemical effects. In comparison to thermal, hydraulic, and mechanical processes, the chemical processes on the discontinuities progress relatively slowly, resulting in limited researches to include these chemical processes. This research introduces mechanisms the involving coupled thermal-hydraulic-mechanicalchemical processes focusing on the rough fracture surfaces and asperities. The chemically-induced changes in mechanical and hydraulic properties are described based on pressure solution and precipitation concepts. A comprehensive review of laboratory tests, field tests, and numerical simulations is conducted related to the chemically-induced coupled processes in fractured rock. Laboratory tests, in particular, concentrate on microscopic changes in fracture asperities induced by pressure solution to analyze chemically-induced aperture changes. The TOUGHREACT, an integral finite difference method program for thermal-hydraulic-chemical simulations, is generally employed to model the chemical response of pressure solution and precipitation on fracture surfaces. The TOUGHREACT includes a module to describe effective porosity and permeability changes based on the modified cubic law, so the real-time change of the fracture permeability can be reflected during the flow simulation. Considering the coupled thermal-hydraulic-mechanicalchemical processes of discontinuity, it becomes evident that the chemical processes under repository conditions (long-term, high temperature, and high pressure) can disturb the hydraulic performance of the natural barrier, so further research is required to characterize the chemically-induced coupled processes for assessing the long-term performance of the natural barrier system.

The compacted bentonite buffer is a key component of the engineered barrier system in deep geological repositories for high-level radioactive waste disposal. Groundwater infiltration into the deep geological repository leads to the saturation of the bentonite buffer. Bentonite saturation results in bentonite swelling, gelation and intrusion into the nearby rock discontinuities within the excavation damaged zone of the adjacent rock mass. Groundwater flow can result in the erosion and transport of bentonite colloids, resulting in bentonite mass loss which can negatively impact the long-term integrity and safety of the overall engineered barrier system. The hydro -mechanicalchemical interactions between the buffer, surrounding host rock and groundwater influence the erosion characteristics of the bentonite buffer. Hence, assessing the critical hydro-mechanicalchemical factors that negatively affect bentonite erosion is crucial for the safety design of the deep geological repository. In this study, the effects of initial bentonite density, aperture, discontinuity angle and groundwater chemistry on the erosion characteristics of Bentonil WRK are investigated via bentonite extrusion and artificial fracture experiments. Both experiments examine bentonite swelling and intrusion into simulated rock discontinuities; cylindrical holes for bentonite extrusion experiments and plane surfaces for artificial fracture experiments. Compacted bentonite blocks and bentonite pellets are manufactured using a compaction press and granulation compactor respectively and installed in the transparent extrusion cells and artificial fracture cells. The reference test condition is set to be 1.6 g/cm3 dry density and saturation using distilled water. After distilled water or solution injection, the axial and radial expansion of the bentonite specimens into the simulated rock discontinuities are monitored for one month under free swelling conditions with no groundwater flow. Subsequent flow tests are conducted using the artificial fracture cell to determine the critical flow rate for bentonite erosion. The intrusion and erosion characteristics are modelled using a modified hydro-mechanicalchemical coupled dynamic bentonite diffusion model and a fluid-based hydro-mechanical penetration model.

Buffer materials play an important role in preventing the leakage of radionuclides from the residue. The mineralogical properties of these buffer materials are critical in repository design. This study presents the fundamental properties of Na-type MX80 and a novel Ca-type Bentonil- WRK. The CaO to MgO ratio in Bentonil-WRK was approximately 1:1, and the CaO to Na2O ratio was approximately 2.8:1. These results suggest that Bentonil-WRK demonstrates a lower swelling index compared to Gyeongju bentonite due to its CaO-to-MgO ratio’s proximity to 1:1, despite having a higher montmorillonite content than Gyeongju bentonite. The results of this research can provide useful foundational data for the evaluation of the thermal-hydraulic-mechanical-chemical behavior of buffer materials.

The presence of technological voids in deep geological repositories for high-level radioactive nuclear waste can have negative effects on the hydro-mechanical properties of the engineered barrier system when groundwater infiltrates from the surrounding rock. This study conducted hydration tests along with image acquisition and X-ray CT analysis on compacted Korean bentonite samples, which simulated technological voids filling to investigate the behavior of fracturing (piping erosion) and cracking deterioration. We utilized a dual syringe pump to inject water into a cell consisting of a bentonite block and technological voids at a consistent flow rate. The results showed that water inflow to fill technological voids led to partial hydration and self-sealing, followed by the formation of an erosional piping channel along the wetting front. After the piping channel generated, the cyclic filling-piping stage is characterized by the repetitive accumulation and drop of water pressure, accompanied by the opening and closing of piping channels. The stoppage of water inflow leads to the formation of macro- and micro cracks in bentonite due to moisture migration caused by high suction pressure. These cracks create preferential flow paths that promote longterm groundwater infiltration. The experimental test and analysis are currently ongoing. Further experiments will be conducted to investigate the effects of different dry density in bentonite, flow rate, and chemical composition of injected water.

In this study, a third metal layer with a higher corrosion potential than copper was introduced between the copper and cast iron layer to strengthen the corrosion resistance of the copper layer which is considered as a corrosion resistant barrier in the disposal container for spent nuclear fuel. Three types of corrosion-resistant metals, silver, nickel, and titanium, were selected as the intermediate insertion layer, and the galvanic specimens of two bonded metals were exposed to KURT (KAERI Underground Research Tunnel) groundwater and a high voltage of 1.0 V was applied to corrode the specimens at electrochemically accelerated condition. Corrosion of copper part was confirmed in Cu-Ti, Cu-Ni, and Cu-Ag galvanic specimens, but copper part was not corroded in Cu-Fe galvanic specimen. If the corrosion-resistant intermediate layer proposed in this study works properly, the local corrosion problem of copper disposal canister is expected to be some degree solved, which can apply to a welding part or a stress concentrated part.

The concept of deep geological disposal for high-level radioactive waste is based on an engineered barrier system (EBS), including a canister, bentonite buffer and backfill material. The bentonite buffer is key component of the EBS to prevent groundwater infiltration and radionuclide leakage. However, the bentonite buffer can become saturated due to groundwater flow through the excavation damaged zone in the adjacent rock, causing erosion of bentonite buffer and affecting the long-term performance of EBS. While the RH (relative humidity) sensor is commonly used to assess the degree of saturation in the bentonite buffer, it has a critical challenge due to its sensor size, which can disturb the overall integrity of the bentonite buffer during the initial installation process. In contrasts, the electrical resistivity test, widely known as a non-destructive method, is used to predict soil properties such as the degree of saturation and water contents. This method measures the electric resistance of materials using electric current induced by electric potential difference between two electrodes. Notably, there is no study that assess the integrity of bentonite buffer in a nuclear waste repository using electrical resistivity measurement. This study presents the electrical resistance numerical module under steady state using commercial finite element method (FEM), and quantitatively estimate the change of electrical resistance according to saturation and erosion of bentonite buffer. Furthermore, the electric potential and current density distribution formed between two electrodes are analyzed.

Compacted bentonite buffer blocks placed in the engineered barrier system for high-level nuclear waste disposal can undergo swelling, intrusion into rock fractures, and erosion with saturation. Bentonite erosion and intrusion can lead to bentonite mass loss via groundwater flow and can ultimately compromise the overall integrity of the disposal system. To ensure the long-term safety of deep geological disposal, it is essential to assess the hydro-mechanical interactions between the bentonite buffer and surrounding rock. In this study, the impact of bentonite erosion and intrusion on the mechanical properties of the jointed rock mass were assessed via elastic wave propagation measurements using the quasi-static resonant column test. Granite rock discs obtained from the Korea Underground Research Tunnel and Gyeongju bentonite were used to simulate jointed rock specimens with different bentonite intrusion conditions. Different degrees of bentonite intrusion were simulated by mixing bentonite and water to create bentonite paste and gel. The longitudinal and shear wave velocities under different normal stress levels were used to quantify the effects of bentonite intrusion on the mechanical characteristics of the rock joint. Complementary numerical analysis using the three-dimensional distinct element code (3DEC) was conducted to provide improved understanding of wave propagation within bentonite gouge-filled rock mass.

The engineered barrier system (EBS) for deep geological disposal of high-level radioactive waste requires a buffer material that can prevent groundwater infiltration, protect the canister, dissipate decay heat effectively, and delay the transport of radioactive materials. To meet those stringent performance criteria, the buffer material is prepared as a compacted block with high-density using various press methods. However, crack and degradation induced by stress relaxation and moisture changes in the compacted bentonite blocks, which are manufactured according to the geometry of the disposal hole, can critically affect the performance of the buffer. Therefore, it is imperative to develop an adequate method for quality assessment of the compacted buffer block. Recently, several non-destructive testing methods, including elastic wave measurement technology, have been attempted to evaluate the quality and aging of various construction materials. In this study, we have evaluated the compressive wave velocity of compacted bentonite blocks via the ultrasonic velocity method (UVM) and free-free resonant column method (FFRC), and analyzed the relationship among compressive wave velocity, dry density, thermal conductivity, and strength parameter. We prepared compacted bentonite block specimens using the cold isostatic pressure (CIP) method under different water content and CIP pressure conditions. Based on multiple regression analysis, we suggest a prediction model for dry density in terms of manufacturing conditions. Additionally, we propose an empirical model to predict thermal conductivity and unconfined compressive strength based on compressive wave velocity. The database and suggested models in this study can contribute to the development of quality assessment and prediction techniques for compacted buffer blocks used in the construction of a disposal repository.

High level radioactive waste disposal repository is faced thermos-hydro-mechanical-radioactive condition. Factors according to these complex conditions are measured using multiple sensors installed in the disposal repository to check integrity of the structure. Wires of the sensors can be potential pathways of groundwater and nuclide flow and these pathways accelerates bentonite saturation. Therefore, it is worth to developing wireless sensors buried in the bentonite buffer which can communicate without wires. In start of the study, widely-utilized wireless communication methods including WiFi and LoRa are tested using compacted bentonite blocks to estimate the performance of them. Compacted bentonite blocks are prepaired using di-press method with metal molds and the dry density of them are about 1.6 g/cm3. All wireless communication methods are well communicated through the bentonite blocks over 50 cm. The further experimental tests will be conducted with different dry density and water contents. The results of these experimental tests give a possibility of wireless communications in compacted bentonite buffer and will be utilized for the design of wireless sensor systems for the repository monitoring.

The engineered barrier system (EBS) is an indispensable element of a deep geological repository (DGR) designed to prevent the discharge of radioactive materials into the environment. The buffer material is a vital component of the EBS by creating a physical and chemical barrier that prevents the migration of radioactive materials. In the disposal environment, gases can be generated from the corrosion of the canister. When the gas generation rate exceeds the diffusion rate, the buffer material’s performance can deteriorate by the physical damage induced by the increase in pore pressure. Therefore, understanding the EBS’s behavior under gas generation conditions is crucial to guarantee the longterm safety and performance of the DGR. Lab-scale and field-scale experiments have been conducted to examine the stability of the buffer material concerning gas generation and movement by the previous researchers. To evaluate long-term stability for more than 100,000 years, it is essential to assess stability using a numerical model verified by these experiments. This study investigated the effect of interfacial characteristics on the numerical modeling accuracy of experimental simulation while verifying a numerical model through field-scale experimental results. The findings of this study are expected to furnish fundamental data for establishing numerical analysis guidelines for the longterm stability assessment of disposal systems.