Hydraulic conductivity is a critical design parameter for buffers in high-level radioactive waste repositories. Most employed prediction models for hydraulic conductivity are limited to various types of bentonites, the main material of the buffer, and the associated temperature conditions. This study proposes the utilization of a novel integrated prediction model. The model is derived through theoretical and regression analyses and is applied to all types of compacted bentonites when the relationship between hydraulic conductivity and dry density for each compacted bentonite is known. The proposed model incorporates parameters such as permeability ratio, dynamic viscosity, and temperature coefficient to enable accurate prediction of hydraulic conductivity with temperature. Based on the results obtained, the values are in good agreement with the measured values for the selected bentonites, demonstrating the effectiveness of the proposed model. These results contribute to the analysis of the hydraulic behavior of the buffer with temperature during periods of high-level radioactive waste deposition.

The bentonite buffer material is a crucial component in an engineered barrier system used for the disposal of high-level radioactive waste. Because a large amount of heat from the disposal canister is released into the bentonite buffer material, the thermal conductivity of the bentonite buffer is a crucial parameter that determines the design temperature. At the Korea Atomic Energy Research Institute (KAERI), a new standard bentonite (Bentonil-WRK) has been used since 2022 because Gyeongju (KJ) bentonite is no longer produced. However, the currently available data are insufficient, making it essential to investigate both the basic and complex properties of Bentonil-WRK. Thus, this study evaluated its geotechnical and thermal properties and developed a thermal conductivity empirical model that considers its dry density, water content, and temperature variations from room temperature to 90°C. The coefficient of determination (R2) for the model was found to be 0.986. The thermal conductivity values of Bentonil-WRK were 1–10% lower than those of KJ bentonite and 10–40% higher than those of MX-80 bentonites, which were attributable to mineral-composition differences. The thermal conductivity of Bentonil-WRK ranged between 0.504 and 1.149 W·(m−1·K−1), while the specific heat capacity varied from 0.826 to 1.138 (kJ·(kg−1·K−1)).

The bentonite buffer material is a crucial component for disposing of high-level radioactive waste (HLW). Several additives have been proposed to enhance the performance of bentonite buffer materials. In this study, unconfined compression tests were conducted on bentonite mixtures as well as pure bentonite buffer material. Joomunjin and silica sands were added at a 30% ratio, and graphite was added at 3% along with bentonite. The unconfined compression strength (UCS) and elastic modulus of pure bentonite were found to be 20% to 50% higher than those of bentonite mixtures under similar dry density and water content conditions. This decrease in strength can be attributed to the reduced cross-sectional area available for bearing the applied load in the bentonitemixture. Furthermore, the 3% graphite-bentonite mixture exhibited a 10% to 30% higher UCS and elastic modulus compared to the 30% sand-bentonite mixtures. However, since the strength properties of additive-bentonite mixtures are lower than those of pure bentonite, it is essential to evaluate thermohydraulic-mechanical functional criteria when considering the use of bentonite mixtures as buffer materials.

In environments where buffer materials are exposed to increased temperature due to the decay heat emitted by radioactive waste, it is crucial to assess the performance of the buffer material in relation to temperature effects. In this study, we conducted experiments using Bentonil-WRK, a calcium-type bentonite, compacted to a dry density of 1.65 g/cm3 and an initial water content of 15%. The experimental temperature conditions were set to 30, 60, 90, 110, and 130°C. We observed that the swelling pressure of the compacted bentonite buffer decreased as the temperature increased. The findings from this study can provide valuable guidance for the design of high-level waste repository in Korea.

Montmorillonite, a versatile clay mineral with a wide range of industrial applications, is often found in natural deposits with impurities that limit its effectiveness. This study investigates the use of column froth flotation as an innovative technique to improve the purity of montmorillonite by selectively removing impurities without affecting its essential properties. Column froth flotation, a well-established mineral separation method, is adapted to address the specific challenges associated with enhancing montmorillonite purity. The process involves conditioning raw montmorillonite with carefully chosen reagents to selectively separate impurities, including quartz, feldspar, and other minerals commonly found alongside montmorillonite in natural deposits. Experimental results confirm the effectiveness of column froth flotation in significantly enhancing the purity of montmorillonite. This method allows for efficient impurity removal while preserving the essential properties of montmorillonite, making it suitable for various industrial applications. The study also explores the optimal conditions and reagent choices to maximize the purification process. In conclusion, column froth flotation offers a promising avenue for enhancing montmorillonite purity without compromising its fundamental properties. This study provides valuable insights into optimizing the process for large-scale industrial applications, facilitating the development of highquality montmorillonite products tailored to specific industrial needs.

Buffer materials are one of the engineering barrier components in high-level radioactive waste disposal facilities. Compacted bentonite has been known as the most suitable buffer material so far, and research is being conducted worldwide to determine the characteristics of suitable bentonite blocks in each country. Therefore, this study aims to compare and analyze various properties of different buffer material candidates, including thermal, hydraulic, and mechanical properties. Buffer material candidates for Korea disposal system, Kyungju Bentonite (KJ-I, KJ-II), and Bentonil- WRK were compared. The properties were compared and analyzed based on experimental and literature data. The data obtained from this report can be used to understand the behavior of buffer materials and assess whether they meet various criteria, such as temperature and saturation, and ultimately serve as an essential input variable database for safety evaluations of disposal systems.

In the design of HLW repositories, it is important to confirm the performance and safety of buffer materials at high temperatures. Most existing models for predicting hydraulic conductivity of bentonite buffer materials have been derived using the results of tests conducted below 100°C. However, they cannot be applied to temperatures above 100°C. This study suggests a prediction model for the hydraulic conductivity of bentonite buffer materials, valid at temperatures between 100°C and 125°C, based on different test results and values reported in literature. Among several factors, dry density and temperature were the most relevant to hydraulic conductivity and were used as important independent variables for the prediction model. The effect of temperature, which positively correlates with hydraulic conductivity, was greater than that of dry density, which negatively correlates with hydraulic conductivity. Finally, to enhance the prediction accuracy, a new parameter reflecting the effect of dry density and temperature was proposed and included in the final prediction model. Compared to the existing model, the predicted result of the final suggested model was closer to the measured values.

Bentonite has been considered as a potential buffer material in the engineering barriers of highlevel radioactive waste disposal systems. The intrusion of groundwater and heat from the waste change the temperature of the bentonite, which can alter the hydraulic properties of the bentonite. In this study, temperature effects on permeability were observed in two Ca-type bentonites. Laboratory tests were conducted on two types of block that were compacted using Korean Gyeongju bentonite and bentonil-WRK at different dry densities. Permeability tests were conducted at three different temperatures, namely 30°C, 60°C, and 90°C, using deionized water. Moreover, comparison between two Ca-type bentonites is carried out.

In order to reduce the area of the high-level radioactive waste (HLW) repository, a buffer material with high thermal conductivity is required. This is because if the thermal conductivity of the buffer material is high, the distance between the disposal tunnels and the deposition holes can be reduced. Sand, which is a natural material and has higher thermal conductivity than bentonite, is added to bentonite to develop an enhanced buffer material. For the sand-bentonite mixture, it is important which sand to use and how much to add because an enhanced buffer material should satisfy both hydraulic (H) and mechanical (M) performance criteria while improving thermal conductivity (T). In this study, we would like to show what type of sand and how much sand should be added to develop an enhanced buffer material by adding sand to Gyeongju bentonite, a representative bentonite in Korea. For this purpose, the thermal conductivity, hydraulic conductivity, and swelling pressure of the sand-Gyeongju bentonite mixture according to the sand addition rate were measured. It is more efficient to use silica sand with smaller particles than Jumunjin sand which is a representative sand in Korea as an additive for an enhanced buffer material than using the Jumunjin sand. In order for the sand-Gyeongju bentonite buffer material to satisfy both the hydraulic and mechanical performance criteria as a buffer material while increasing the thermal conductivity, it is judged that the optimum dry density is 1.7 g/cm3 at least and the optimum sand addition rate is 10% at most.

The buffer block, which is one of the main components of the engineering barrier system, plays an essential role in mitigating groundwater infiltration and radionuclide transport in a high-level nuclear waste repository. To achieve those purposes, the compacted buffer block must satisfy the functional safety criteria for dry density, water content, and many other components. In this study, the compation curves of the compacted bentonite-sand mixtures were evaluated to identify the relationship between the dry density and the water content of the buffer material. The floating die press at 10 MPa and the cold isostatic press at 40 MPa were applied to compaction of a buffer block with a diameter of 100 mm and a thickness of 10 mm. The condition of a bentonite-sand mixing ratio was 6:4, 7:3, 8:2, and 9:1 with 9 to 21% water content. As a result, the maximum dry density increases, the optimum moisture content decreases as the sand content of buffer material increases. This study can provide the conditions for manufacturing the compacted bentonite-sand buffer block.

The buffer is a critical barrier component in an engineered barrier system, and its purpose is to prevent potential radionuclides from leaking out from a damaged canister by filling the void in the repository. No experimental parameters exist that can describe the buffer expansion phenomenon when Kyeongju bentonite, which is a buffer candidate material available in Korea, is exposed to groundwater. As conventional experiments to determine these parameters are time consuming and complicated, simple swelling pressure tests, numerical modeling, and machine learning are used in this study to obtain the parameters required to establish a numerical model that can simulate swelling. Swelling tests conducted using Kyeongju bentonite are emulated using the COMSOL Multiphysics numerical analysis tool. Relationships between the swelling phenomenon and mechanical parameters are determined via an artificial neural network. Subsequently, by inputting the swelling tests results into the network, the values for the mechanical parameters of Kyeongju bentonite are obtained. Sensitivity analysis is performed to identify the influential parameters. Results of the numerical analysis based on the identified mechanical parameters are consistent with the experimental values.

A compacted bentonite buffer is a major component of engineered barrier systems, which are designed for the disposal of high-level radioactive waste. In most countries, the target temperature required to maintain safe functioning is below 100°C. If the target temperature of the compacted bentonite buffer can be increased above 100°C, the disposal area can be dramatically reduced. To increase the target temperature of the buffer, it is necessary to investigate its properties at temperatures above 100°C. Although some studies have investigated thermal-hydraulic properties above 100°C, few have evaluated the water suction of compacted bentonite. This study addresses that knowledge gap by evaluating the water suction variation for compacted Korean bentonite in the 25–150°C range, with initial saturations of 0 and 0.22 under constant saturation conditions. We found that water suction decreased by 5–20% for a temperature increase of 100–150°C.

The buffer material plays a role in preventing the excessive rise in temperature generated from the high-level radioactive waste by dissipating the decay heat to the rock. For this reason, the buffer material must have thermal properties to ensure the performance of the deep geological repository. This study measured the thermal conductivity of sand-bentonite according to the mixing ratio to improve the thermal properties. The compacted buffer was manufactured with a sand-bentonite mixing ratio of 6:4, 7:3, and 8:2 with 9 to 12% water content. As a result, the thermal conductivity increases as the ratio of sand increases. As a further study, it is necessary to experiment on whether sand-bentonite’s hydraulic, mechanical, and chemical performance is suitable for the stable operation of a repository.

To decrease area of the repository for high-level radioactive waste, enhancing the disposal efficiency is needed for public acceptance. Previous studies regarding the performance assessment of KRS and KRS+ repository did not consider area-based variations of the geothermal gradient and rock thermal properties in Korea. This research estimated deposition hole spacing based on performance assessment of a repository using the distribution of geothermal gradient and rock thermal properties in Korea to increase disposal efficiency. Distributions of geothermal gradient, rock thermal properties were investigated based on 2019 Korea geothermal atlas published by Korea Institute of Geoscience and Mineral Resources (KIGAM). Effect of thermal performance parameters was analyzed using coupled thermal-hydraulic numerical simulations, and effect of rock thermal conductivity and deposition hole spacing on the maximum temperature of buffer was relatively large. In addition, distribution maps of thermal performance of a repository and deposition hole spacing were plotted using thermal performance parameters-maximum temperature of buffer regression equations and GIS data given by KIGAM. In the regions showing the highest maximum temperature of buffer in Korea, required deposition hole spacings were 10.5 m, 10.0 m, 10.1 m, respectively for KJ-II, MX-80, and FEBEX bentonite cases, and thereby additional disposal area of 40%, 33.3%, and 34.7% were required compared to that of the KRS+ repository. On the other hand, high disposal efficiency can be obtained in the regions showing the low maximum temperature of bentonite buffer. The methodology provided in this research can be used as one of the references for the selection of domestic candidate repository sites. Additional mechanical performance analysis should be conducted using distributions of mechanical properties of rock mass in Korea.

Increasing thermal conductivity of buffer materials makes the disposal tunnel and hole spacings in high-level radioactive waste (HLW) repositories decrease, so that the area of the HLW repository decreases, which gives more choices to choose the HLW repository site and economical cost savings to construct HLW repositories. Thus, developing enhanced buffer materials with improved thermal conductivity is needed. One of the methods to develop enhanced buffer materials is to add additives to the bentonite which is main material for buffer materials. Most additives have high thermal conductivity, but most additives do not swell or less swell than bentonite, so that the swelling pressure of the enhanced buffer materials by additives decreases compared to the swelling pressure of pure bentonite buffer materials. Swelling pressure is an important performance criterion to design buffer materials. Thus, it is important to confirm the swelling pressure of the enhanced bentonite. However, it is not simple to measure the swelling pressure of the buffer materials and furthermore, it takes several days to measure the swelling pressure of the buffer materials. For these reasons, swelling index can be considered to predict the swelling pressure of the enhanced buffer materials relatively. In this study, it was investigated through tests how the swelling index of bentonite-sand mixtures change according to the amount of sand and it was found that the linear relationship between swelling index and sand amount in the bentonite-sand mixtures.

Various models have been proposed to describe the swelling behavior of buffer in high level waster repository. One of the most notable models, the Barcelona Basic Model (BBM), is a mechanical model that simulates the behavior of unsaturated ground and is widely applied to soils that undergo large expansion due to water. Among the BBM parameters of Kyeongju bentonite, which is found in Korea, there are no experimental data for parameters that describe the unsaturated state. Such hydromechanical properties should be characterized through experimental programs. However, such experiments are highly complicated and require long periods of time to produce an unsaturated state through different methods according to the suction range. Although there are several studies in which geotechnical parameters were obtained through a back analysis instead of direct experiments, few studies have employed machine learning methods for the identification of geotechnical parameters. In this study, instead of direct experiments, the results of a relatively simple swelling pressure experiment was compared to the numerical analysis results to propose a method of determining some of BBM parameters. Influential factors were identified by a sensitivity analysis and the values of the factors were estimated using an artificial neural network and optimization method. The obtained parameters were applied to the numerical model to estimate the swelling pressure growth, which was subsequently compared to the experimental value. As a result, it was found that there was no significant difference between the two swelling values.

A geological repository system consists of a disposal canister with packed spent fuel, buffer material, backfill material, and intact rock. Among these, the bentonite buffer is one of the most important components to assure the safe disposal of high-level radioactive waste (HLW). As the bentonite buffer is installed as a block type, it is important to fabricate homogeneously. Generally, floating die method and cold isostatic press (CIP) method are used to fabricate bentonite blocks. In this paper, two bentonite blocks were produced using float die method at first, and CIP method was additionally applied to just one block. After that, several samples were cored from two blocks. The dry density and water content of several samples produced from two blocks were measured.

Colorectal cancer causes the most cancer-associated death worldwide, having a high cancer incidence. Pectin is a complex polysaccharide present in various fruits, emerging as an anti-carcinogenic candidate. Although pectin has a suppressive capacity for colon carcinogenesis, the effect of reactive oxygen species (ROS) generation and colonic aberrant foci formation in the colon carcinogenesis mouse model remains unclear. Therefore, this study investigates the regulatory effect of pectin supplementation on colon carcinogenesis induced by azoxymethane (AOM) and dextran sodium sulfate (DSS) in mice. In an animal experiment, thirty male institute for cancer research (ICR) mice were divided into two experimental groups; AOM/DSS (control group) and AOM/DSS + pectin (5% in drinking water). Furthermore, the number of aberrant crypt foci (ACF) and aberrant crypt (AC) on colonic mucosa were counted, and thiobarbituric acid-reactive substances (TBARS) assay was performed to estimate lipid peroxidation in feces. Pectin treatment significantly decreased the number of ACF and AC per colon compared with the control. Additionally, fecal TBARS level in the pectin group was significantly lower than those in the control group. Conclusively, these findings indicate that pectin-inhibited hyperplastic alteration and oxidative stress suppress colitis-associated colon carcinogenesis.

In the majority of countries, the upper limit of buffer temperature in a repository is set to below 100℃ due to the possible illitization. This smectite-to-illite transformation is expected to be detrimental to the swelling functions of the buffer. However, if the upper limit is increased while preventing illitization, the disposal density and cost-effectiveness for the repository will dramatically increase. Thus, understanding the characteristics and creating a database related to the buffer under the elevated temperature conditions is crucial. In this study, a strategy to investigate the bentonite found in Korea under the elevated temperatures from a mineral transformation and radionuclides retardation perspective was proposed. Certain long-term hydrothermal reactions generated the bentonite samples that were utilized for the investigation of their mineral transformation and radionuclide retardation characteristics. The bentonite samples are expected to be studied using in-situ synchrotron-based X-Ray Diffraction (XRD) technique to determine the smectite-to-illite transformation. Simultaneously, the ‘high-temperature and high-pressure mineral alteration measurement system’ based on the Diamond Anvil Cell (DAC) will control and provide the elevated temperature and pressure conditions during the measurements. The kinetic models, including the Huang and Cuadros model, are expected to predict the time and manner in which the illitization will become detrimental to the performance and safety of the repository. The sorption reactions planned for the bentonite samples to evaluate the effects on retardation will provide the information required to expand the current knowledge of repository optimization.