<Objective> Injection of a linear transgene into male pronucleus has been widely used to produce Transgenic (Tg) mice. This approach however is inefficient and results in concatemerised transgene insertion and associated reduced protein expression from such insertions. The objective of this study is to develop active transgenesis method by using a piggyBac transposase plasmid DNA, and generate double transgene harboring transgenic mice. <Method> We examined the piggyBac transposase plasmid (pm- GENIE‐3) on its ability to produce transgenic animals with NaOH, HCl and FuGENE6 treated sperm followed by ICSI‐Tr, for its effectiveness in creating EGFP Tg mice, as judged by offspring epifluorescence. After these steps, we explored if the embryo development affects ICSI‐Tr efficiency by using substrate‐free media or aphidicolin. Moreover, we tested to determine if transgenesis is possible by directly injecting the DNA into the cytoplasm or into pronuclei. Finally, we attempted the introduction of two transgenes, such as EGFP and dsRED simultaneously in one transposon and the ability to generate double Tg mice by using NaOH treated sperm during ICSI‐Tr. <Results> The best results were obtained when sperm were treated with NaOH and co‐incubated with circular plasmid DNA of pmGENIE‐3. This resulted in Tg pups that could successfully express EGFP, with efficiencies of 37.9% of born animals being transgenic. Furthermore, the effectiveness of this method was proved by the production of Tg offspring from inbred strains of mice, such as C57BL/6, Balb/c and CD‐1 nude. While injection of DNA into the pronucleus or cytoplasm of one cell embryos, and delayed embryo development‐method were not as effective as ICSI‐Tr in producing Tg mice, they nevertheless proved successful. Finally, NaOH‐ICSI‐Tr successfully obtained Tg mice expressing both the EGFP and dsRED transgene. In conclusion, the current study developed an active form of NaOH‐ICSI‐Tr mediated transgenesis utilizing the piggyBac transposition machinery, and was successful in obtaining Tg mice which expressed simultaneously not only EGFP but also the dsRED transgene stably inserted in these animals.

In order to clarify the wear resistance as cutting tools, the effect of oxygen addition on oxidation behavior of the β-Si3N4 ceramics with 5 mass% Y2O3 and 2 or 4 mass% Al2O3 was investigated by performing oxidation tests in air at 1300° to 1400°C and cutting performance tests. From test results, we could conclude that the mechanical properties of β-Si3N4 ceramics depending on oxygen introduction are much effective on cutting performance improvements of β-Si3N4 ceramics.

Sintered materials have been applied widely in Valve Seat Inserts (VSI). The demands for VSIs are not only good heat and wear resistance but also good machinability. The sintered materials, which are made of a mixture of manganese containing iron powder and certain types of sulfide powder, have superior machinability due to precipitation of the fine MnS particles in the matrix. This report introduces a new VSI material, which has both superior machinability, and wear resistance due to applies of this "MnS precipitation" technique.

Sintered materials have been applied widely in Valve Seat Inserts (VSI). The amount of wear on VSIs increases when used in gas (LPG, CNG) engines because of their dry environments. In this paper, two newly developed high performance VSI materials for gas engines are introduced. These materials applied new techniques, which are both high performance hard particle and new distribution method of solid lubricant, to increase wear resistance.

WC-TiC-TaC binderless cemented carbide was oxidized under low partial pressure of oxygen (50ppm) at 873K for 1 to 20 h. Surface roughness was measured using atomic force microscope, and effect of TiC amount on oxidation behavior of the carbide was investigated. WC phase was oxidized more easily than WC-TiC-TaC solid solution phase. With an increase in TiC amount, WC-TiC-TaC phase increased and the oxidation resistance of the carbide increased.

The effect of TiC content on oxidation behavior of the sintered WC-TiC-TaC alloys with 2 mass% TaC and different TiC amounts of 3-45 mass% was investigated through oxidation tests in air at 973K. As a result of the tests, it was revealed that with increasing TiC content in the alloys, mass changes caused by oxidation and thickness of the scale decreased. Thus, it is considered that the main component of the scales changed gradually from to with increasing TiC content in the alloys, and oxygen diffusion through the scale to the alloys was inhibited gradually.

This paper is aimed to study the computer simulation of sintering process for ceramics by Monte Carlo and molecular dynamics methods. Plural mechanisms of mass transfer were designed in the MC simulation of sintering process for micron size particles; the transfer of pore lattices for shrinkage and the transfer of solid lattices for grain growth ran in the calculation arrays. The MD simulation was performed in the case of nano size particles of ionic ceramics and showed the characteristic features in sintering process at atomic levels. The MC and MD simulations for sintering process are useful for microstructural design for ceramics.