The damaged spent fuel rods must be stabilized by encapsulation or dry re-fabrication technologies before geological disposal. For applying the dry re-fabrication technology, we manufactured a vertical type furnace to perform the fuel material recovery from damaged fuel rods by oxidative decladding technology. As driving forces to accelerate oxidative decladding rate, magnetic vibration and pulse hammering generated by a pneumatic cylinder were used in this study. The oxidative decladding efficiency and recovery rate of fuel oxide powder with rod-cut length, oxidation temperature and time, oxygen concentration, and gas mixtures were investigated using simfuel rod-cuts in a vertical furnace for fuel material recovery and powder quality improvement. The oxidative decladding was performed for 2.5-10 h as following operation parameters: simfuel rod-cut length of 50-200 mm, oxidative temperature from 450 to 580°C, oxygen concentration of 49.5 or 75.6%, and gas mixtures in O2/Ar or O2/N2. In magnetic vibration, oxidative decladding was progressed only at bottom portion of fuel rodcut. Whereas, oxidative decladding in pulse hammering was occurred at both top and bottom portions of fuel-rod. In pulse hammering method, the oxidative decladding conditions to declad rod-cuts of 50- 200 mm in length were established to achieve both decladding efficiency of ~100% and fuel material recovery rate of > 99%. These conditions were as follows: oxidation temperature and time at 500°C and 2.5-10 h, oxygen concentration at 75.6% under O2/N2 gas mixtures. As operation conditions for a pneumatic cylinder, stroking, actuating, and waiting times were 0.5, 3, and 12 s.

Ag-containing aluminosilicate sorbents capable of capturing iodine were prepared by sol-gelation from Na, Al, and Si alkoxides using co-solvent exchange, Ag/Na ion exchange, solvent exchange, and ambient-pressure drying. The Na+AlSi-OH gel was prepared using sodium methoxide (NaOMe): aluminum tri-sec-butoxide (Al(OsBu)3): tetraethyl orthosilicate (TEOS) molar ratios of 1.05:1:1, 1.3:1.1:1, 1.5:1.3:1. The solvent effect on textural properties such as Brunauer-Emmett-Teller (BET) surface areas and pore size distributions and Ag0 particle sizes was investigated using water with high surface tension, isopropanol and n-heptane with low surface tension. The BET surface area, average pore size, and cumulative pore volume for sorbents strongly increased with decreasing surface tension of solvents and increasing Al/Si atomic ratios. In addition, Ag0 particle sizes increased with decreasing surface tension of solvents.

The damaged spent fuel rods must be stabilized by encapsulation or dry re-fabrication technologies before geological disposal. For applying the dry re-fabrication technology, we manufactured a vertical type furnace to perform both fuel material recovery from damaged fuel rods by oxidative decladding and sinterability improvement of fuel powder by repetition of oxidative and reaction treatment. A horizontal type furnace provides only a diffusion-controlled reaction resulting in longer reaction time and decreasing amount of powder for oxidation and reduction, whereas a vertical type furnace with a submerged gas distributor gives rapid reaction due to flowing gas-solid contact by fluidization. For observation of fluidization behaviors of uranium oxides at room temperature, fluidized column was prepared with transparent cylindrical tube, pressure transmitter and gas flow meter. Number of size of orifice holes was determined by equations in Fluidization Engineering [D.Kunii, O. Levenspiel]. Before uranium oxide test, as surrogates, WO2 (10.8 g/cm3) and Ta2O5 (8.2 g/cm3) powder similar to density of UO2 (10.96 g/cm3) and U3O8 (8.3 g/cm3), respectively were used to achieve fluidization operation conditions in the region from minimum to expanded fluidization. Fluidization behaviors and pressure drop of powder bed was observed according to operation parameters such as gas velocity, number and size of orifice holes, and powder amount.

목 적 : 가입한 (±)구면렌즈 굴절력에 대응하는 조절력의 변화를 비교하여 렌즈의 적응효과를 알아보았다. 방 법 : 평균연령 21.76±1.76세의 51명(남자 26명, 여자 25명)을 대상으로 하였다. 대상자들의 완전교정 된 눈 앞에 S+1.00 D, S+2.00 D, S+3.00 D, S-1.00 D, S-2.00 D, S-3.00 D를 순서대로 가입하여, 가입 직 후, 15분 후, 그리고 30분 후에 각 단안조절력을 측정하였다. 측정값들은 완전교정 상태의 조절력과 비교 하였고, 렌즈 가입 전·후 측정된 단안조절력의 변화값은 가입한 굴절력 값에 대한 상대 비율로 계산하였다. 결 과 : S+1.00 D, S+2.00 D, S+3.00 D 가입 후 조절력은 완전교정 조절력보다 모두 유의하게 (p<0.001) 증가되었지만, 가입된 렌즈굴절력의 약 55~68% 수준이었다. S-1.00 D, S-2.00 D, S-3.00 D 가입 후 조절력은 완전교정 조절력보다 모두 유의하게(p<0.001) 감소되었고, 가입된 굴절력의 약 72~105% 수준이었다. 결 론 : 조절변화를 목적으로 구면렌즈를 처방할 때, 임상전문가들은 렌즈적응으로 인해 더해준 구면굴절 력 값보다 조절변화량이 대부분 감소될 것이라는 점을 고려해야 한다.

Despite the importance of behavioral ecotoxicological tests, few researches have been conducted to assess the quality of freshwater using behavior of test species, in part due to lack of standardized test method for quantifying the response. In this study, we developed a new test methods using non-biting midge larva’s burrowing behavior to assess field water quality and a new index, AUC (area under curve), to compare burrowing behavior quantitatively. Four kinds of field samples (residential, natural, agricultural and industrial areas) were tested using the method to validate our methodology and index. There were not significant differences in 96 h mortality and heavy metal concentration between samples, but AUC from the industry sample was significantly decreased.

In this study, we modeled a ship or marine structure into a rectangular resistance body and tried to examine surrounding flow characteristics and pressure distributions behind the resistance body experimentally and investigated pressure characteristics by a 3-dimension numerical simulation. As a result, the reattachment point of the mainstream separated from the upper part and proceeding to the rear part was about x/H=6, but by the influence of the negative pressure area formed behind the resistance body and interference of the flow flowed in winding from left and right, the reattachment point of some flows was formed near x/H=1.33. The perpendicular velocity component behind x/H=0 varies in size with the recycle flow shapes formed from the influence of the resistance body, but generally it shows a negative distribution and there is a decreasing pattern as it goes to the down part. We verified the result of the calculation by comparing the velocity distribution of 3-dimension numerical simulation using a commercial software and the PIV(particle image velocimetry) measurements. In the numerical simulation results, the static pressure characteristic behind the resistance body was proportional to the inflow velocity, and the dynamic pressure shows a similar pattern with constant-velocity from the experiment.

고준위폐기물처분장에서 완충재는 오랜 기간 동안 방사성핵종의 붕괴열과 여러가지 화학조건의 지하 수에 노출되며, 이러한 열수조건은 완충재물질의 차수 및 핵종저지 방벽성능에 심각한 영향을 줄 수 있 다. 본 연구에서는 국산 스멕타이트를 대상으로 열수실험을 수행하고, 열수반응에 의한 스멕타이트 점토 의 팽창도, 층전하, 양이온교환능의 변화를 조사하였다. 열수실험 결과, 온도와 용액 중 칼륨농도를 증가 시켰을 때, 스멕타이트의 팽창도는 감소하였고, 층전하는 더 큰 음전하를 가졌으며, 양이온교환능도 감소 하였다.

Elevated expression of survivin is strongly associated with tumorigenesis and even in human common cancers. The purpose of this study is to confirm whether survivin is associated with odontogenic tumor expecially in the development and growth in ameloblastomas. For the control group; 3 specimens obtained from normal oral mucosa without any inflammatory reaction were used. For the experimental group, specimens obtained from 17 subjects of ameloblastomas; follicular type, plexiform type, granular cell type, acantomatous type and unicystic ameloblastoma. All the specimens were embedded in paraffin, sectioned 5μm or more in thickness, and stained with hematoxylin- eosin stain method. For immunostain, the specimens were incubated with 1:200 diluted primary antibody, followed by the secondary antibody. The bound antibodies were visualized by addition of diaminobenzidine tetrahydrochloride (DAB) for 30 minutes at room temperature. The specimens were counterstained with Gill’s Hematoxylin and mounted. Intensity of survivin immunoreactivity specimens was quantitatively scaled using under the light microscope with the following criteria; Intensive reaction; +++, Moderate reaction; ++, Minimal reaction; +. Using the image analyzer (Korea Optical System), immunoreactivity of the tumor cells in various fields was measured and statistically analyzed with SPSS 17.0 Program. In control group, moderate positive reaction was noted in the cytoplasm of cells in the basal and spinous layer, but negative reaction was revealed in the nucleus. Expression of survivin was significantly increased in the cytoplasm of ameloblastomas as compared to that of control group (p<0.05). Expression of survivin in the nucleus and the cytoplasm of the tumor cells between subtype of ameloblastoma was not significantly different. These results suggest that expression of survivin is closely associated with the development, and growth of the ameloblastomas. However it is unlikely that survivin can be used as a marker for cellular malignancy.

고준위폐기물처분장의 완충재 물질로 사용되는 팽윤성 점토는 방벽재로서 그 기능을 제대로 발휘하기 위해 오랫동안 물리 화학적으로 안정해야 한다. 팽윤성 점토의 장기건전성 관련인 자들을 검토하고, 처분장 성능에 대한 각 인자의 중요성을 평가하였다. 검토결과, 붕괴 열에 의한 온도상승, 지하수 화학, 콘크리트에 의한 pH 증가, 유기물과 미생물, 방사선 조사 및 기계적 교란은 완충재물질로서 팽윤성 점토의 장기건전성에 중요한 인자임을 확인하였다. 본 연구는 고준위폐기물 처분장에서 팽윤성 점토의 완충재 설계를 위한 기초자료로 유용하게 활용될 것이다.

고준위폐기물처분장의 공학적 성능은 공학적 방벽의 열적-수리적-역학적 거동에 의해 크게 좌우된다. 2002년에 제안된 기준처분시스템 완충재의 열적-수리적-역학적 거동 실증을 위해서, 엔지니어링 규모의 실증장치인 KENTEX를 제작설치 하였다. 이 실증실험은 2005년 5월 31일에 시작하여 현재 진행 중에 있다. 본 논문에서는 운전 중인 KENTEX시설과 이 시설에서 수행 중인실험 및 향후 연구내용을 소개하고, 또한 센서 설치 및 운전조건 결정을 위해 수행한 운전 전 T-H-M 모델 계산결과도 기술하였다. 한국형 기준처분시스템의 실증연구와 관련하여, KENTEX 실증실험은 향후 추진될 지하시험시설에서의 현장시험에 필요한 자료와 경험을 제공하고, 기준처분시스템의 열적-수리적-역학적 거동특성과 평가모델을 검증할 것이다. 실험적으로는 처분장 완충재로 사용되는 벤토나이트 블록의 제작 및 설치에 대한 엔지니어링 타당성을 보여 주는데 유용하게 활용될 것이다.