PURPOSES: The objectives of this study are to analyze the current status of pothole during a rainy season and to suggest a future pavement maintenance method via pothole analysis. METHODS: Potholes are caused by moisture submerged in pavement. The pore pressure caused by traffic and environmental loads causes failure between the aggregate and asphalt binder. Thus, heavy rain is a primary pothole creator, especially in aged pavement. To prevent accidents on roadways, Gyeonggi-do has initiated a fast pothole repair program. However, the number of potholes increase every year. In this study, the current status of potholes and maintenance methods are analyzed. Based on these results, a future pavement maintenance method is suggested. RESULTS AND CONCLUSIONS : Gyeonggi-do’s pothole situation is worse than Seoul’s. Problems were founded, as follows. The amount of potholes was large, and the number increased annually. Pothole management is done at a basic level, because there is no long-term plan. Potholes occur frequently at the same site because of the poor quality of emergency repair. Finally, there is no systematic and comprehensive pavement management. Thus, pothole prevention measures are ill-prepared. Therefore, to reduce potholes and to manage high quality pavement, it is necessary to make a long-term pavement management plan.

PURPOSES : Exposed aggregate concrete pavements have been adopted in several countries because of their advantages of pavement texture characteristics, which can produce low tire-pavement noise and higher load-carrying capacities. The magnitude of tire-pavement noise greatly depends on the wavelength of pavement texture. The wavelength of exposed aggregate concrete pavement can be controlled with maximum sizing and by controlling the amount of coarse aggregates in the concrete mixture. In this study, the maximum size and the amount of coarse aggregate in the exposed aggregate concrete pavement are investigated to produce equal levels of wavelength in the asphalt pavement. METHODS: A simple method to measure the average wavelength of pavement texture is introduced. Subsequently, the average wavelength of typical asphalt pavement is investigated. A set of mixture designs of exposed aggregate concrete with three maximum-sized coarse aggregates, and three amounts of coarse aggregate are used. The average wavelengths are measured to find the mixture design needed to produce equal levels of wavelength as typical asphalt pavement. RESULTS : With a cement content of 420 kg/m3 and fine aggregate modulus of 30%, the number of exposed aggregates was 48, and the shortest texture depth provided a wavelength of 4.2 mm. According to the number of exposed aggregates, the exposed aggregate concrete pavement could be rendered low-noise, because its wavelength was similar to that of asphalt pavement ranging from 3.9 to 4.4 mm. CONCLUSIONS : Selection of appropriate maximum sizes and the amount of coarse aggregates for exposed aggregate concrete pavement can produce a wavelength texture closely resembling that of asphalt pavement. Therefore, the noise level of exposed aggregate concrete pavement can be reduced with an appropriate maximum size and the amount of coarse aggregates are employed.

PURPOSES: Using recyclable materials in asphalt pavement industry is one of the essential tasks not only for saving construction budgets but also for mitigating environmental pollutions. Over the past decades, several efforts have been made by road maintenance agencies to incorporate various recyclable materials into virgin asphalt paving mixtures. As a result, reclaimed asphalt pavement (RAP), which consists of old pavement material was selected as one of most widely used recyclable materials. In this paper, the effects of using different amounts of single-recycled RAP (SRRAP) and double-recycled RAP (DRRAP) on the low-temperature characteristics of asphalt mixtures were investigated. METHODS: To evaluate the low-temperature characteristics of SRRAP and DRRAP mixtures, two experiments, the bending beam mixture creep test and semicircular bending fracture test were performed. The experimental parameters: creep stiffness, m-value, thermal stress, critical cracking temperature, fracture energy, and fracture toughness were computed then compared. RESULTS : RAP mixtures (SRRAP or DRRAP) showed lower mechanical performance compared with conventional asphalt mixtures. The differences became distinct with increased RAP addition. However, the performance differences between SRRAP and DRRAP mixtures were not significant in all cases, which indicate the possible application of re-recycling technology (DRRAP) in the asphalt pavement industry. CONCLUSIONS : The addition of RAP to virgin asphalt can mitigate low-temperature performance despite the improvement in fracture performance observed in some cases. Therefore, using RAP (SRRAP or DRRAP) mixtures on inter or sublayer construction, but not on the surface layer, is recommended. Moreover, the possibility of applying double-recycling technology in asphalt pavement industry can be introduced in this study because not significant performance differences were found between SRRAP and DRRAP mixtures especially at low temperature.

PURPOSES: The purpose of this study is to determine the effective maintenance method for a deteriorated jointed plain concrete pavement by evaluating the long-term performance of the repaired concrete overlay sections. METHODS: Long-term performance evaluation was conducted for the test section at the intersection between SeoPa and IlDong in National Road No. 37. Firstly, the distress conditions of the concrete pavement, which was constructed in December 2003, were evaluated by referring to the existing report. Secondly, the results of pretreatment, material properties, and initial performance evaluation were analyzed for the overlay test conducted in 2011. Finally, a field survey was carried out using visual inspection and nondestructive testing with a FWD in August 2018, and long-term performance evaluation was conducted for about seven years after maintenance. RESULTS: Visual inspection of the old concrete pavement showed severe damage such as joint spalling and asphalt patching. The cores taken from the old concrete had indirect tensile strength of 2.6-3.8 MPa. It is difficult to determine the freeze-thaw resistance because the average amount of air was only 1.6-2.2%, and spacing factor values were over 400㎛ regardless of location. During maintenance, overlay and partial depth repair were performed by applying three types of overlay materials which are typical in Korea. On the material side, high compressive strength (over 40 MPa) and chlorine ion penetration resistance (less than 1,000 coulomb) at 56 days were achieved. In August 2018, seven years after maintenance, visual inspection and nondestructive testing using FWD were conducted for long-term performance evaluation. Regardless of the maintenance materials, surface deficiencies such as spalling and map cracking occurred extensively near the joint. CONCLUSIONS: In conclusion, if the strength and durability index of aged concrete pavement is low, then it was determined that partial depth repair at the joint is not an effective maintenance alternative. In the case of overlay, the durability of the overlay material is considered the most important factor. In the absence of adequate reinforcement at the joint of the distressed concrete pavement, freeze-thaw damage caused by moisture penetration through the joint and failure of the old concrete are repeated, making it difficult to ensure long-term durability.

PURPOSES : In Korea, concrete pavements with transverse tining, which have excellent skid resistance, have been mainly constructed to secure road bearing capacity and safety. However, transverse tining has higher noise level of approximately 4-5 dB(A) compared with asphalt pavement. As a method to determine low-noise characteristics of concrete pavements, the fine-size exposed aggregate concrete pavement (EACP) has been studied in Korea and abroad. The surface of EACPs consists of exposed coarse aggregates and 2-3 mm removal surface mortar. EACPs have the advantages of maintaining low-noise and adequate skid-resistance levels during the performance period. Although EACPs have been widely studied to reduce noise, quantitative noise analysis with various paving methods has not been performed owing to differences in mixture proportioning, construction conditions, environmental conditions, and measurement methods. Therefore, the purpose of this study is to investigate the low-noise characteristics of fine-size EACPs by comparing noise with various paving methods, including concrete and asphalt pavements. METHODS: In this study, noise data were collected to quantitatively analyze the low-noise characteristics of EACPs compared with various paving methods such as transverse tining, longitudinal tining, SMA, and HMA. RESULTS: The evaluation of the low-noise characteristics of EACPs compared with transverse tining showed that the relative noise of 13 mm EACP with transverse tining was reduced by approximately 2% at 60 km/h, 4% at 80 km/h, and 5% at 100 km/h. The relative noise of 10 mm EACP with transverse tining was reduced to 3%, 7%, and 8% at 50 km/h, 80 km/h, and 100 km/h, respectively. In addition, it was confirmed that the noise of 10 mm EACP was similar to that of asphalt pavement. CONCLUSIONS : It was confirmed that EACP using 10 mm coarse aggregates generates lower noise than that using 13 mm coarse aggregates. Therefore, the use of coarse aggregates smaller than 10 mm needs to be considered to improve the low-noise effect of EACP.

PURPOSES: Using recycled asphalt materials (called Reclaimed Asphalt Pavement: RAP) from existing asphalt pavement layers in newly constructed asphalt pavement is an essential option not only for lowering the construction budget but also for mitigating environmental pollution for society. For this reason, many pavement agencies in South Korea, the USA, and Canada have observed the effect of RAP on conventional asphalt pavement to evaluate and set proper material specifications and addable amounts. In this paper, effect of recyclable material on low-temperature performance of asphalt materials was investigated with two different mechanical tests. Among the recyclable material sources, RAP and Taconite Aggregate (TA), which is mainly produced in northern Minnesota (USA), were considered. METHODS : To evaluate the low-temperature mechanical performance of a RAP mixture, two different experimental tests (In-Direct Tensile (IDT) low temperature creep test and Semi-Circular Bending (SCB) test) were considered. The mechanical parameters creep-stiffness, relaxation modulus, fracture energy, and fracture toughness were computed then compared. RESULTS: More brittle characteristics were observed with RAP-added asphalt mixtures compared to the conventional asphalt mixtures, as expected. However, the differences of computed mechanical performances were not significantly distinct for RAP mixtures compared to conventional mixtures when the RAP proportion was around 20%, and with the addition of TA up to 20%. CONCLUSIONS : It can be concluded that up to 20% of RAP addition (along with TA up to 20%) in a virgin asphalt mixture does not provide significant performance reduction. This addable proportion can be viewed as a successful minimum level when considering the addition of RAP to hot-mix asphalt (HMA). Moreover, applying TA with RAP could offer a successful alternative for asphalt recycling and the materials industry.

PURPOSES: The performance of both string line and multi-sonic sensor systems were investigated with respect to achieving smoothness in a 5 cm-thick Stone Mastic Asphalt (SMA) wearing layer. METHODS: String line and multi-sonic sensor systems were applied in the leading and trailing lanes, respectively, with two-lane simultaneous paving. RESULTS: Two systems did not show any significant statistical difference in initial International Roughness Index(IRI). The multi-sonic sensor system produced smoothness similar to that by the string line system. CONCLUSIONS : The string line system was found to be very effective in eliminating roughness below a wavelength of about 2 m, confirming that a string line reference is the best system to obtain a smoother surface. A multi-sonic sensor system evidently demonstrated the capability of replicating a reference level and, partly showed a roughness averaging effect within the system length. It can further be concluded that the effect of smoothness of the underlying layer on the upper layer smoothness cannot be ignored.

PURPOSES: The objective of this study was to develop an asphalt pavement response model for a subsurface cavity section using the 3D finite element method and a statistical approach. METHODS: It is necessary to analyze the structural behavior of asphalt pavement with a subsurface cavity to evaluate the degree of risk for a road cave-in. A 3D finite element model was developed to simulate the subsurface cavity underneath asphalt pavement and was verified using the ILLIPAVE program. Finite element analysis was conducted for asphalt pavement sections with different asphalt layer thickness/modulus, and cavity depth and length, to generate the artificial pavement response database. The critical pavement response considered in this study was the tensile strain at the bottom of the asphalt layer because fatigue cracking is the main cause of road cave-in. The relationship between the critical pavement response and influencing factors was investigated using the pavement response database. The statistical regression approach was adopted to develop the asphalt pavement response model for predicting the critical pavement response of asphalt pavement with a subsurface cavity. RESULTS : It was found from the sensitivity analysis that the asphalt layer thickness or modulus, and cavity depth or length, are the major factors affecting road cave-in incidents involving asphalt pavement. The asphalt pavement response model showed high accuracy in predicting the tensile strain at the bottom of asphalt layer. It was found from the verification study that the R square value between finite element model and pavement response model were 0.969 and 0.978 in the cavity and intact sections, respectively. CONCLUSIONS: The work reported in this paper was intended to figure out the pavement structural behavior and to develop a pavement response model for the occurrence of cavities underneath asphalt pavement using 3D finite element analysis. In the future, critical pavement response will be utilized to establish the criteria of risk of road cave-in based on various different conditions.

PURPOSES: In this study, algorithms were proposed for determining the crack condition of an asphalt pavement image using deep learning methods. METHODS: For the configuration of a deep learning network, the study used a Convolution Neural Network and You Only Look Once algorithms. To obtain input data for analysis, a camera was mounted on the bonnet of the vehicle to obtain images of asphalt pavement and to mark the ground-truth cracks in the asphalt pavement image. In addition, an algorithm suitable for the automatic determination function of Deep Learning was proposed in order to calculate the crack ratio and crack rating. RESULTS: The result of analysis showed that the recall rate of cracks in this system was higher from FPPW 5.0E-06 to 96.03%. Furthermore, the accuracy of the grading system was found to be 100%, enabling the determination of very accurate ratings. The rate of processing per image was 0.4448 seconds on average, and the real-time analysis of pavement images presented no problem because the assessment took place within a short time. CONCLUSIONS : Applying this system to the pavement management system is expected to reduce the time required in finishing work and to determine a quantitative crack rating.

PURPOSES : This paper proposes a design framework for planetary road infrastructure by considering the characteristic environment, natural resource, and loading conditions on the Moon and Mars. METHODS : From the perspective of civil engineering, available literatures such as technical articles, NASA (National Aeronautics and Space Administration) Technology Roadmaps 2015, Strategic Knowledge Gap, and mechanistic-empirical pavement design method are comprehensively reviewed for planetary road construction. The concept of in situ resource utilization (ISRU) is re-interpreted by comparing ISRU on the Earth and Moon with emphasis on the significance of interconnection between resource utilization and infrastructure development. RESULTS : According to the literature reviews, the factors that have significant effect on planetary road pavement design, construction, and maintenance are selected and evaluated. In addition, by considering the interconnection issue, a design framework is suggested that includes the resource issues not only of planetary road pavement but also of construction equipment. Subsequently, the framework is widened to apply for preliminary planetary infrastructure. CONCLUSIONS : Although the proposed preliminary design framework is not conclusive and has to be elaborated, an initial framework to consider interconnection issues and ISRU is suggested for planetary road pavement. The suggested framework will be applied for road pavement design and will be used to evaluate the cost-benefit ratio of alternatives.

PURPOSES: This study analyzes feasibility for application white pavement markings in the roadways with median barrier. METHODS : By reviewing numerous relevant laws, standards, and operational cases, the white pavement markings' excellence was demonstrated. Driver’s behavior was analyzed through a virtual driving experiment using driving simulator and field tests. RESULTS: First, white pavement markings are superior to yellow pavement markings in terms of visibility, economics, and safety. Second, as a result of virtual driving experiment, the color of line in the roadway with median barrier didn’t affect the driver’s behavior such as the average vehicle speed, the distance bias in the lane and the separation distance from the centerline. Third, field test demonstrated that the driver tended to recognize the median barrier as an obstacle. In addition, the central driving ratio in the lane was increased due to improving the visibility of line at night in case of the white pavement markings. CONCLUSIONS : The application of white pavement markings in the roadways with median barrier can enhance traffic safety by improving the visibility of line at night.

PURPOSES : In this study, the propriety of expansion joint spacing of airport concrete pavement was examined by using weather and material characteristics. METHODS: A finite element model for simulating airport concrete pavement was developed and blowup occurrence due to temperature increase was analyzed. The critical temperature causing the expansion of concrete slab and blow up at the expansion joint was calculated according to the initial vertical displacement at the joint. The amount of expansion that can occur in the concrete slab for 20 years of design life was calculated by summing the expansion and contraction by temperature, alkali-silica reaction, and drying shrinkage. The effective expansion of pavement section between adjacent expansion joints was calculated by subtracting the effective width of expansion joint from the summation of the expansion of the pavement section. The temperature change causing the effective expansion of pavement section was also calculated. The effective expansion equivalent temperature change was compared to the critical temperature, which causes the blowup, according to expansion joint spacing to verify the propriety of expansion joint applied to the airport concrete pavement. RESULTS: When an initial vertical displacement of the expansion joint was 3mm or less, the blowup never occurred for 300m of joint spacing which is used in Korean airports currently. But, there was a risk of blow-up when an initial vertical displacement of the expansion joint was 5mm or more due to the weather or material characteristics. CONCLUSIONS: It was confirmed that the intial vertical displacement at the expansion joint could be managed below 3mm from the previous research results. Accordingly it was concluded that the 300m of current expansion joint spacing of Korean airports could be used without blowup by controling the alkali-silica reaction below its allowable limit.

PURPOSES: The permeable pavement type has been rapidly developed for solving problems regarding traffic noise in the area of housing complex and heavy rainwater drainage in order to account for the climate change. In this regards, the objective of this study is to figure out the characteristics of pavement types. METHODS: The laboratory test for deriving optimum asphalt content (OAC) was conducted using the mixtures of the permeable asphalt surface for the pavement surface from Marshall compaction method. Based on its results, the pavement construction at the test field was conducted. After that, the site performance tests for measuring the traffic noise, strength and permeability were carried out for the relative evaluation in 2 months after the traffic opening. The specific site tests are noble close proximity method (NCPX), Light falling deflectometer test (LFWD) and the compact permeability test. RESULTS : The ordered highest values of the traffic noise level can be found such as normal dense graded asphalt, drainage and porous structure types. In the results from LFWD, the strength values of the porous and drainage asphalt types had been lower, but the strength of normal asphalt structure had relatively stayed high. CONCLUSIONS: The porous structure has been shown to perform significantly better in permeability and noise reduction than others. In addition to this study, the evaluation of the properties and the determination of the optimum thickness for the subgrade course under the porous pavement will be conducted using ground investigation technique in the further research.

PURPOSES : The objective of this study is to develop a pavement rehabilitation decision tree considering current pavement condition by evaluating severity and distress types such as roughness, cracking and rutting. METHODS: To improve the proposed overall rehabilitation decision tree, current decision tree from Korea and decision trees from other countries were summarized and investigated. The problem when applying the current rehabilitation method obtained from the decision tree applied in Seoul was further analyzed. It was found that the current decision trees do not consider different distress characteristics such as crack type, road types and functions. Because of this, different distress values for IRI, crack rate and plastic deformation was added to the proposed decision tree to properly recommend appropriate pavement rehabilitation. Utilizing the 2017 Seoul pavement management system data and considering all factors as discussed, the proposed overall decision tree was revised and improved. RESULTS: In this study, the type of crack was included to the decision tree. Meanwhile current design thickness and special asphalt mixture were studied and improved to be applied on different pavement condition. In addition, the improved decision tree was incorporated with the Seoul asphalt overlay design program. In the case of Seoul's rehabilitation budget, rehabilitation budget can be optimized if a 25mm milling and overlay thickness is used. CONCLUSIONS: A practical and theoretical evaluation tool in pavement rehabilitation design was presented and proposed for Seoul City.

This study was conducted to develop a heat interception permeability aggregate pavement material that resists increase of air temperature and has permeability by decreasing pavement temperature of city in summer. For this study, a heat interception polymer binder mixed with heat interception material and polyurethane binder. And the study made heat interception permeability aggregate pavement material by mixing heat interception polymer binder. Using the materials, the study conducted flexural strength test and temperature reduction effect experiment. As the result, flexural strength was 5.43MPa average and the temperature reduction effect was effective up to maximum 16 degrees Celsius compared to current asphalt concrete.

Subsurface cavities in the asphalt pavement which can cause road depression and cave-in accidents influence on the safety of pedestrians and vehicle drivers in the urban area. The existence of subsurface cavity can increase the tensile strain at the bottom of asphalt layer which is an indicator of fatigue cracking potential, and leads to the weakening of the pavement structural capacity. In this study, the finite element (FE) analysis was conducted to examine the relationship between the critical pavement responses and influencing factors, such as cavity depth and size, asphalt layer thickness, and asphalt concrete modulus. The surface deflections and tensile strains calculated from the ABAQUS FE program were compared to those from ILLIPAVE. It is found from this comparison that there are a good relationship between two analysis results. A three dimensional finite element model which is essential to simulate the hexahedral cavity were used to generate the synthetic database of critical pavement responses. To validate the developed model, the deflection data obtained from field Falling Weight Deflectometer (FWD) testing in four different locations were compared to FE deflections. It is found that the center deflections obtained from the FWD testing and FE analysis are similar to each other with an error values of 2.7, 4.4, 5.5, and 11.9 % respectively. The FE model developed in this study seems to be acceptable in simulating actual field cavity condition. On the basis of the data in the database, various analyses were conducted to estimate the effect of influencing factors on the critical pavement responses. It was found that the tensile strain at the bottom of asphalt layer is affected by all the factors but the most affected by the cavity depth and asphalt concrete modulus. Further studies are recommended to properly account for the effect of cavity’s geometry to pavement response.

Cold recycled asphalt has been utilized to overcome high energy consumption and working temperature and low recycled pavement material percentage in hot mix asphalt and concrete pavement [1]. Up to dates, asphalt recycling on site called as Cold In-Place Recycling (CIR), Cold Central Plant Recycling (CCPR) and even hot recycling technologies have been developed and applied to the fields, but limitations such as poor adhesion between gravel and asphalt, slow hydration time, bleeding pavement are reported, respectively [2, 3, 4]. Among these issues, hydration time and initial strength in application are all related to the property of mineral filler influencing the mechanical property of pavement mixture. Due to these reasons, there have been continuous needs to develop new mineral filler to overcome previously reported issues by with the respects of mineral composition, hydration reaction and surface reaction enhancement. In this study, several natural minerals such as alumina, silicate, and calcium oxide were utilized as raw materials and following characterizations using SEM, EDS, XRD, and BET were performed to evaluate materials properties and suggest research directions for the optimum mineral filler development.

In the United States and Europe, new environmentally friendly asphalt pavement has been researched as an alternative to traditional hot asphalt pavement. After the Paris Convention of 2015, policies should be found to reduce carbon dioxide. In the field of asphalt pavement, new methods are needed to reduce carbon dioxide from the traditional hot asphalt pavement. In Korea, waste asphalt is growing and natural aggregate is running dry. So the government is implementing policies to increase the use of waste resources. So, it created a new asphalt pavement method to reduce CO2 and use waste asphalt. It is a cold recycled asphalt pavement. Emulsified asphalt has a balance of dispersibility, stability, and adhesive between water, aggregates, and asphalt. But, the physical properties of emulsified asphalt can be degraded compared to traditional hot asphalt pavement. So there are limitations in actual use. The study compared the softening point, elastic recovery, and penetration properties of asphalt mix compounds by using latex in emulsified asphalt. In particular, cations latex was used for the emulsified asphalt, which could further improve the physical properties.

The world-wide need to reduce the energy used and the greenhouse gases emitted during cement manufacture has led to the pursuit of more eco-efficient materials, such as ground granulated blastfurnace slag(GGBS) and fly ash. Especially, GGBS is a by-product generated during the manufacture of pig ions. GGBS can be divided into water-cooled slag(WS) and air-cooled slag(AS). With comparison of WS, the AS is formed by allowing the molten slag to cool relatively slowly under ambient conditions. This study presents experimental findings on the mechanical and durability performance of cement concrete pavement with replacement of cement by WS and/or AS. In order to produce concrete specimens, total replacement of cement by GGBS(WS+AS) was fixed at 40% by mass. Concrete specimens were regularly monitored for the variation of mechanical properties such as flexural strength, compressive strength and initial surface absorption. In addition, in order to assess durability of concrete pavement with WS and/or AS, the chloride ion penetration resistance and scaling resistance tests were adopted, and the corresponding results were compared to those of plain concrete pavement. The test results indicated that the performance of concrete pavement was significantly dependent on the replacement level of WS by AS. Concrete specimens incorporating 20% replacement level of AS showed a poor mechanical performance, while 5% replacement of AS showed a beneficial effect both mechanical and durability performance. Especially, the 5% AS replacement led to the higher resistance of concrete pavement against frost-salt action. Based on the experimental results, the present study would be helpful to design high-performance cement concrete pavement.