This study examines paraelectric Bi1.5Zn1.0Nb1.5O7 (BZN), which has no hysteresis and high dielectric strength, for energy density capacitor applications. To increase the breakdown dielectric strength of the BZN film further, poly(vinylidene fluoride) BZN-PVDF composite film is fabricated by aerosol deposition. The volume ratio of each composition is calculated using dielectric constant of each composition, and we find that it was 12:88 vol% (BZN:PVDF). To modulate the structure and dielectric properties of the ferroelectric polymer PVDF, the composite film is heat-treated at 200 oC for 5 and 30 minutes following quenching. The amount of α-phase in the PVDF increases with an increasing annealing time, which in turn decreases the dielectric constant and dielectric loss. The breakdown dielectric strength of the BZN film increases by mixing PVDF. However, the breakdown field decreases with an increasing annealing time. The BZN-PVDF composite film has the energy density of 4.9 J/cm3, which is larger than that of the pure BZN film of 3.6 J/cm3.

경량콘크리트와 FRP 보강근을 사용하여 구조체를 만들기 위해서는 경량콘크리트와 FRP 보강근과 사이의 부착특성을 파악하는 것이 대단히 중요하다. 앞선 연구에서 보통콘크리트와 이형 GFRP 보강근 사이의 정규화된 부착강도는 전경량콘크리트와 이형 GFRP 보강근 사이의 정규화된 부착강도보다 크게 나타났으나, 보통콘크리트와 모래분사형 GFRP 보강근 사이의 정규화된 부착강도는 전경량콘크리트와 모래분사형 GFRP 보강근 사이의 정규화된 부착강도보다 작은 값으로 나타났다. 이러한 결과는 보통콘크리트의 부착강도가 전경량콘크리트의 부착강도보다 더 클 것이라는 ACI의 일반적인 예상에 반하는 것이다. 따라서 본 연구에서는 전경량콘크리트가 아닌 모래경량콘크리트와 모래분사형 GFRP 보강근 사이의 부착특성을 실험을 통하여 분석하고 경량콘크리트와 모래분사형 GFRP 보강근 사이의 그 일반적인 경향을 조사하였다. 실험 결과, 모래경량콘크리트에 모래분사형 GFRP 보강근을 사용한 경우의 정규화된 부착강도 역시 보통콘크리트에 모래분사형 GFRP 보강근을 사용한 경우보다 크게 나왔으며, 추후 경량콘크리트와 모래분사형 GFRP 보강근 사이의 부착특성에 대하여 더 많은 조사가 필요하다고 판단된다.

In this paper, 'Pico scope' was used to measure and analyze high voltage waveforms of 'Grade injector' and 'IQA injector' due to defective solenoid injector of CRDI diesel engine, and the following conclusions were obtained. In the case of the injector of 'Grade Injector' and 'IQA Injector', there was no change in the injection timing of the injector while the injector was installed. However, by controlling the operation time, It is judged that the injector control is insufficiently controlled when the number of revolutions of the engine is increased to 2000 rpm and 3000 rpm in the idling state in the idling state because the injector failure is precisely controlled in the idling state, When determining the fault injector, the waveform of the 'Grade injector' and 'IQA injector' can be detected by waveform analysis by comparing the injection control time by measuring the high voltage waveform of the injector control in idle idling state. Can be easily diagnosed and maintained. I hope this study will be handed to the mechanics to make diagnosis of CRDI injector convenient.

The effect of EGR on fuel economy was investigated in a gasoline direct injection engine. The 1-D cycle simulation program of GT-Power was utilized to evaluate fuel consumption rate. At high load, fuel consumption increased by about 2~6% according to EGR rate. Knock mitigation was the main effects, gaining about 80% of the total fuel consumption improvement. At low load, fuel consumption reduction was 0.6~2%, which was much lower than that for high load. The lower improvement of fuel consumption at low load is attributed to solely dilution and chemical effects of exhaust gas.

This paper investigates the relationship between the waveform area and fuel injection quantity. It is on developing on analysis method of waveform the effect of waveform area on fuel injection quantity of CRDI Diesel engine. The experimental methods using Pico oscilloscope and fuel injection tester are employed to measure current and voltage waveform and fuel injection quantity of solenoid injector. The one normal and two abnormal solenoid injectors are used. The experiment is carried out during no-load condition. A summary of the important results are as follows. 1) The area of the voltage and current waveform of the abnormal injector becomes larger than the that of normal injector, and the area of the current and voltage waveform is inversely proportional to the fuel injection quantity. 2) The area of the current waveform can be obtained more accurate results than that of voltage waveform. 3) It is possible to infer the fuel injection quantity by measuring the current waveform and calculating the area.

본 연구에서는 물 직분사 시스템을 이용한 복숭아 적뢰·적화작업 가능성을 판단하기 위하여 성능 시 험을 수행하였다. 직분사 시스템은 농약방제용 동력분무기에 자체 개발한 직분사 분무건을 장착한 형태 로서 직분사 성능이 우수하고, 내마모성이 뛰어난 특수노즐을 사용하였다. 개발된 직분사 시스템의 주 요 영향 인자를 도출하기 위해 동력분무기 압력, 분사거리, 노즐직경에 따른 분사충격량과 분사집중도 를 도출하였으며, 복숭아 결과지내 꽃눈 적뢰·적화 시의 성능을 검증하기 위한 요인시험을 수행하였 다. 시험에서는 분무방향, 동력분무기 압력, 분사거리, 노즐직경에 따른 적뢰·적화율과 적엽아율을 도 출하였다. 시험 결과, 적뢰·적화율은 특정 작업조건인 경우 주요 꽃눈 생육단계인 분홍기, 풍선기 및 개화기에서 모두 약 70% 이상, 적엽아율은 10% 이하인 것으로 나타났다. 이러한 결과는 개발된 적뢰· 적화 시스템이 현장에서 적용 가능한 수준의 성능을 가지는 것을 의미하는 것으로, 본 연구 결과는 향 후 실증시험을 위한 기초자료로서 활용될 것이다.

This research aims to analyze the potential possibility of the butyl ether (BE, oxygenates of di-ether group) as a fuel additives for a naturally aspirated direct injection diesel engine fuel. Compared with the diesel fuel, smoke emission decreased approximately 26% by applying the blended fuel(diesel fuel 80 vol-% + BE 20vol-%) at the engine speed of 2,500 rpm and with full engine load. There was none significant difference between the blended fuel and the diesel fuel on the power, torque, and brake specific energy consumption rate of the diesel engine. But, NOx emission from the blended fuel was higher than that of the commercial diesel fuel. As a counter plan, the EGR method was employed to reduce the NOx. We found the possible area where the simultaneous reduction of the smoke and the NOx emission from the diesel engine was achieved by applying the BE blended fuel and the cooled EGR method.

Biodiesel fuel (BDF) can be effectively used as an alternative fuel in diesel engines. The BDF, however, may affect performance and exhaust emissions of the diesel engine because it's physical and chemical properties are different with from the diesel fuel such as viscosity, compressibility and so on. To investigate an effect of injection timing on characteristics of performance and exhaust emissions with the BDF in an IDI diesel engine, this research applied the BDF derived from soybean oil in this study. The engine was operated with six different injection timings from TDC to BTDC 12 ˚CA and six different loads at the engine speed of 1500 and 2000 rpm. In less then the BDF 20, it showed the similar trend compare to the diesel fuel. But, the best injection timing was 2˚CA retarded compare to the diesel fuel with BDF 50.

Butanol has an ability to improve the ignition quality due to its lower latent heat of vaporization; it has an advantage to reduce a volume of a fuel tank because its energy density is higher than that of ethanol. Also, butanol-diesel oil blending quality is good because butanol has an effect to prevent the phase-separation between two fuels. Even if the blended oil contains water, it can reduce the corrosion of the fuel line. Thus, it is possible to use butanol-diesel oil blended fuel in diesel engine without modification, and it may reduce the environment pollution due to NOx and particulate and the consumption of diesel oil. Therefore, some studies are being advanced whether butanol is adequate as an alternative fuel for diesel engines, and the results of the combustion and exhaust gas emission characteristics are being presented. Though the injection and spray characteristics of butanol are more important in diesel combustion, the has not yet dealt with the matter. In this study, the influence in which differences of physical properties between butanol and diesel oil may affect the injection and spray characteristics such as injection rate, penetration, spray cone angle, spray velocity and process of spray development were examined by using CRDI system, injection rate measuring device and spray visualization system. The results exhibited that the injection and macroscopic spray characteristics of two fuels were nearly the same.

디젤엔진에서는 2차 분사 시스템은 다양한 배기 시스템에 적용이 가능하고, 엔진 제어와 관계없이 독립적으로 제어가 가능하기 때문에 환원제 희석 면에서도 후분사 또는 다른 농후한 환원제 분위기 형성 방법 등에 비해 장점이 많다. 2차 분사 시스템에서는 환원제의 공급 방법에 따라서 촉매의 효율은 달라질 수밖에 없다. 환원제는 일정압력 이상으로 유지 및 최적화가 필요하고, 인젝터의 위치 및 각도의 선정은 매우 중요한 인자이다. 본 논문에서는 2차 분사 조건을 변화시켜 환원제의 농도와 양을 변화시켰다. De-NOx 촉매 시스템에서 최대의 NOx 정화 효율에 적합한 환원제 분사 조건들의 선정이 필요하고, 분무 도달거리, 분무 평균 입경, 분무각, 분사량 등의 분무 특성과 환원제의 균일 분포를 잘 파악하여야 한다. 이와 같은 목적을 위하여 2차 분사에서 충돌판 형상에 의한 분무 및 거동 특성은 가시화 방법과 디지털 화상 처리 기법을 사용하여 분석하였으며, 충돌판 형상의 영향성과 각 형상에 대한 최적 각도 범위를 도출하였다.

FRP (Fiber Reinforced Polymer) reinforced lightweight concrete structures can offer corrosion resistance and weight reduction effect simultaneously, so practical use of the structures may be expected afterwards. But, to construct the concrete structures using lightweight concrete and FRP bar, one of many important things to be previously investigated is to study bond characteristic between the lightweight concrete and the FRP bar. So, bond characteristics between lightweight concrete and two types of GFRP bar (helically deformed GFRP bar and sand coated GFRP bar) were investigated in this study. To do this study, literature review and bond strength test using a number of bond strength specimens were conducted. As a result, it could be seen that the bond strength of helically deformed GFRP bar and sand coated GFRP bar in the lightweight concrete were 49% and 81%, respectively, for the bond strength of steel reinforcement in the normal concrete.

화물창의 내부 세정은 압축공기 또는 고압수를 이용하고 있으나 전용 세정기를 이용하지 않은 경우 위험성이 높은 작업이다. 이 연구에서는 화물창 고압세척기를 개발하기 위해 분사노즐의 유동특성을 수치해석 기법을 적용하여 고찰하였다. 그 결과 입자의 크기는 영향은 크지 않았으며 공급압력이 높을수 록 노즐부 끝단에서 유속과 분사거리는 지수함수로 증가하였다.

Biodiesel as alternative energy source of the traditional petroleum fuels has increased interest, because environmental pollution based exhaust emissions from vehicle became serious. The advantage of biodiesel produced from esterification of vegetable and animal oils can be used without the modification of existing diesel engine, but glycerin is generated by production process. In this study, the usability of non-esterification biodiesel as an alternative fuel was investigated in a indirect injection diesel engine. The non-esterification biodiesel has not generated glycerin in esterification process and reduced the 20 percent of cost because it has not used methanol in the production process. Experiments were conducted by using the 5, 10 and 20 percentage of biodiesel and 4 and 8 percentage of biodiesel with 1 and 2 percentage of WDP in baseline diesel fuel. The smoke emission of biodiesel was reduced in comparison with diesel fuel, but power, torque and brake specific energy consumption was similar to diesel fuel.