In this study, we examined the effect of orifice diameter on atomization performance such as SMD(Sauter Mean Diameter), MMD(Mass median diameter), particle size distribution, spray distance, and spray angle when water was sprayed through a siphon nozzle. In addition, the behavior characteristics of spray were analyzed using the CFD(Computational Fluid Dynamics) commercial program. In the downstream direction of the flow, the dispersion and diffusion power of the droplets increased, greatly improving atomization performance. The spray spread in the radial direction when the jet velocity of water increased. As a result, atomization performance improved as the jet velocity increased.

In this study, factors analysis is performed for reducing friction in elevation motion of a large television stand over 50-inch. The first is a pipe type cross-section control for accurate position control of the piston rod. Here it was compared with the pipe type and labyrinth type orifice cross-section. The second study is for optimized piston structure development by comparison pipe orifice and labyrinth orifice. Consequently, in the orifice cross section study between pipe type and labyrinth type through CAE and experimental consideration, cross section of labyrinth type orifice is preferred for reducing of friction. The result of optimized piston structure development through experiment is fixed orifice specification as labyrinth orifice because pipe orifice is founded slip up/down phenomenon of the Ø0.4~1.0 orifice and the labyrinth orifice is not founded that of the Ø0.4~0.6 orifice both tests on 300 mm intervals.

In this study, factors analysis is performed for reducing friction in elevation motion of a large television stand over 50-inch. The first is a pipe type cross-section control for accurate position control of the piston rod. Here it was compared with the pipe type and labyrinth type orifice cross-section. The second study is for specification decision and volume compensation experiment as an apparatus for compensating of the volume of the cylinder is compressed as the volume of piston rod. Consequently, in the orifice cross section study between pipe type and labyrinth type through CAE and experimental consideration, cross section of labyrinth type orifice is preferred for reducing of friction. The result of total consideration in stability problem and performance of volume compensation for specification decision and volume compensation experiment is determined the final speculation of hollow rod φ8×φ4 and riveting system.

In this study, factors analysis is performed for reducing friction in elevation motion of a large television stand over 50-inch. The first is a pipe type cross-section control for accurate position control of the piston rod. Here, it was compared with the pipe type and labyrinth type orifice cross-section. The second study attempted to reduce the frictional force the gas seal lip technology. As the result of the first study, in the orifice cross section study between pipe type and labyrinth type through CAE and experimental consideration, cross section of labyrinth type orifice is preferred for reducing of friction. As the result of the second study, in the gas seal lip technology, the outer-inner diameter of φ20×φ8 in the test result of hollow rod is revealed more proper if the weight of 50 inch television assumed as 30kgf.

덕트에 설치되는 오리피스는 압력과 유량 제어용으로 많이 활용되고 있다. 선박의 거주 구역에 통풍 덕트는 환기와 배기를 위해 설치되며 및 선박의 설계 및 건조 후 검사는 공기 유속과 유량 그리고 소음 기준에 대해 수행된다. 이 연구에서는 선박의 선실 별 유량분배에 중요한 요소인 T-분지관을 대상 으로 오리피스를 적용한 경우 난류운동에너지 분포를 고찰하였다.

Recently, the Ranque-Hilsch vortex tube is widely used for the local cooler of industrial equipment for special purpose. Although many studies on energy extraction in the vortex tube using air as the working fluid have been made so far, a few experimental studies treated solid particles extraction for incompressible fluid. So, an experimental study for the solid particles extraction in the vortex tube(Ranque-Hilsch vortex tube) using the water which is essentially an incompressible fluid is presented. The experiments were carried out with various cold end orifice diameter ratios ranging from 0.25 to 0.70, the input pressure ranging from 1 to 3MPa was considered. The emphasis was given to examine the effect of geometry factors of vortex tube at working fluid(water) for solid particles(Al2O3) extraction. The optimum geometry factor and inlet pressure for the maximum solid particles extraction was found that the smaller cold end orifice diameter ratio and the higher inlet pressure in experimental condition increase.

High-pressure abrasive entrained jet have rapidly become important machining technology over the last two decades. However, suspension jet by high-pressure has been recently developed for packaging sawing. Ideally, diamond materials should be used for components in abrasive water-jet systems that are subject to high erosive conditions. Using the diamond orifices improve maintenance and extend wear part life. This paper gives insights to using an abrasive suspension jet with diamond orifice. The influences of orifice material and orifice design are evaluated.

가스터빈에서 연료 분무 노즐은 연소 특성에 영향을 미치는 중요한 부품이다. 스월 분무 장치를 설계하기 위하여 유량과 분무액적 평균 직경을 설계변수로 정하고 연료 분무 노즐의 최적화를 수행하였다. 설계변수는 이중 노즐의 실험값들을 비교하여 중요한 영향을 미치는 변수로 선정하였다. 민감도는 유량과 분무액적 평균 직경의 변화에 따른 값을 사용하였다. 이중 오리피스형 스월 분무장치의 형상 최적설계를 통하여 유량의 미립화를 높이도록 연구하였다. 최적설계를 위하여 실험 계획법을 이용하였으며, 영향을 적게 미치는 설계변수들은 설계대상에서 제외하였다. 분무 노즐의 분무액적 평균 직경을 사용한 결과는 Jasuja의 액적 평균 이론을 이용하여 도출된 결과와 유사함을 알 수 있었다. 연구 결과는 이중 오리피스형스월 분무장치와 이와 비슷한 종류의 노즐 최적화를 위한 특성을 파악하고 최적의 유량과 허용 공차를 제시하였다.

최근 구조물 진동제어 연구분야에서는 반능동형 진동제어(제진)장치어 대한 연구가 활발하게 진행되고 있다. 반능동형 제진장치는 수동형의 장점인 신뢰성과 경제성 및 능동형의 장점인 적용성(순응성)을 얻을 수 있기 때문이다. 본 연구에서는 반능동형 제진장치의 일종으로 2톤급 반능동형 오리피스 유체댐퍼를 설계ㆍ제작하여 구조물의 적용을 통해 성능을 검증하였다. 수동형 오리피스 유체댐퍼에 2단 솔레노이드 밸브를 설치하여 반능동형을 구현하였다. 단독 성능시험을 통해 동특성을 파악하고, 시험용 철골구조물 적용시험을 통해 외부하중을 받는 구조물의 진동제어용 장치로서의 가능성을 확인하였다.