In South Korea, the level of Highway Pavement Management System (HPMS) was developed since early 2000. During this time numbers of professional pavement condition monitoring equipment were developed and applied in the actual field. One of the remarkable results is 3D Pavement condition Monitoring profiler vehicle (3DPM) designed and developed in Korea Expressway Corporation Research Division (KECRD). Thanks to this equipment, The surface condition of current pavement can successfully be monitored and proper following management strategy cab be established. However, the inner condition of pavement layer cannot be monitored dur to limitation of 3DPM equipment. In this paper, Bending Beam Rheometer (BBR) mixture creep test was performed to verify the effectiveness of current 3DPM equipment. It was found that the current 3DPM equipment has reasonable feasibility on surveying pavement condition.

PURPOSES : The purpose of this study is to provide basic data to improve the service life of asphalt pavement using basalt aggregate in Jeju Island by evaluating the performance of asphalt pavement through analysis of material and structural aspects. METHODS : To evaluate the performance of Jeju Island's asphalt pavement, cracks, permanent deformation, and longitudinal roughness were analyzed for the Aejo-ro road, which has high traffic and frequent premature damage. Cores were collected from Aejo-ro sections in good condition and damaged condition, and the physical properties of each layer were compared and analyzed. In addition, plate cores were collected from two sections with severe damage and the cause of pavement damage was analyzed in detail. RESULTS : About 45% of the collected cores suffered damage such as layer separation and damage to the lower layer. The asphalt content of surface layer in the damaged section was found to be 1.1% lower on average than that in the good condition section, and the mix gradations generally satisfied the standards. The density difference between the cores of each layer was found to be quite large, and the air voids was found to be at a high level. CONCLUSIONS : Test results on the cores showed that, considering the high absorption ratio of basalt aggregate, the asphalt content was generally low, and the high air voids of the pavement was believed to have had a significant impact on damage. High air voids in asphalt pavement can be caused by poor mixture itself, poor construction management, or a combination of the two factors. Additionally, the separation of each layer is believed to be the cause of premature failure of asphalt pavement.

PURPOSES : The objective of this study is to develop the data driven pavement condition index by considering the traffic and climatic characteristics in Incheon city. METHODS : The Incheon pavement condition index (IPCI) was proposed using the weighted sum concept with standardization and coefficient of variation for measured pavement performance data, such as crack rate, rut depth, and International Roughness Index (IRI). A correlation study between the National Highway Pavement Condition Index (NHPCI) and Seoul Pavement Condition Index (SPI) was conducted to validate the accuracy of the IPCI. RESULTS : The equation for determining the IPCI was developed using standardization and the coefficient of variation for the crack rate, rut depth, and IRI collected in the field. It was found from the statistical analysis that the weight factors of the IPCI for the crack rate were twice as high as those for the rut depth and IRI. It was also observed that IPCI had a close correlation with the NHPCI and SPI, albeit with some degree of scattering. This correlation study between the NHPCI and SPI indicates that the existing pavement condition index does not consider the asymmetry of the original measured data. CONCLUSIONS : The proposed pavement condition provides an index value that considers the characteristics of the original raw data measured in the field. The developed pavement condition index is extensively used to determine the timing and method of pavement repair, and to establish pavement maintenance and rehabilitation strategies in Incheon.

PURPOSES : The numeric-based Highway Pavement Management System (HPMS), along with an advanced three-dimensional pavement condition monitoring profiler vehicle (3DPM), in South Korea has presented remarkable advancements in pavement management since the early 2000. Based on these results, visual distress on pavement surfaces can be easily detected and analyzed. Additionally, the entire expressway pavement surface conditions in South Korea can be easily monitored using the current graphical user interface-based advanced information graphic (AIG) approach. Therefore, a critically negative pavement section can be detected and managed more easily and efficiently. However, the actual mechanical performance of the selected pavement layer still needs to be investigated in a more thorough manner not only to provide more accurate pavement performance results but also to verify the feasibility of the current 3DPM and AIG approaches. In this study, the low-temperature performance of the selected asphalt pavement layer section was evaluated to further verify and strengthen the feasibility of the current 3DPM and AIG approaches developed by the Korea Expressway Corporation. METHODS : Based on 3DPM and AIG approach, the positive and negative-riding-quality road sections were selected, respectively. The asphalt material cores were extracted from each section then bending beam rheometer mixture creep test was performed to measure their low-temperature properties. Based on the experimental results, thermal stress results were computed and visually compared. RESULTS : As expected, the asphalt material from the negative driving performance section presented a poorer low-temperature cracking resistance than that from the positive driving performance section. CONCLUSIONS : Current 3DPM equipment can successfully evaluate expressway surface conditions and the corresponding material performance quality. However, more extensive experimental studies are recommended to verify and strengthen the findings of this study

PURPOSES : In this study, a method for evaluating concrete bridge deck deterioration using three-dimensional (3D) ground penetrating radar (GPR) survey data and its in situ application are discussed. METHODS : Field surveys are conducted on two bridges in Yongsan-gu (Bridge A) and Seodaemun-gu (Bridge B) in Seoul using 3D GPR. The obtained survey data are used to calculate the dielectric constant map of each bridge using the extended common midpoint method. In addition, random points on both bridges are selected for the chloride content test in accordance with the KS F 2713 standard. The results from the dielectric constant map and chloride content test are compared. RESULTS : For Bridge A, it is discovered that the percentage of sections with a dielectric constant of 5.0 or less is 1.57%, whereas that above 5.0 is 98.43%; this indicates that the percentage of deteriorated sections for Bridge A is low. Meanwhile, for Bridge B, the dielectric constants calculated for the entire bridge exceed 5.0, which suggests no deterioration for Bridge B. Moreover, all the points selected for the chloride content test have less than 0.15% chloride content and have dielectric constants ranging from 5.0 to 7.0, which are favorable condition for the bridge deck. CONCLUSIONS : The analysis results of the dielectric constants of the concrete bridge deck obtained from the 3D GPR system are consistent with the actual chloride content results. Furthermore, additional verification of this method through field surveys on bridge sections with severe deterioration is highly recommended for future improvements.

PURPOSES : The purpose of this study is to establish a scientific and rational structure pavement maintenance technique and management standard through field investigation and analysis method development for measuring damage to structure pavement such that fundamental quality improvement can be promoted and the life of pavement prolonged. METHODS : In this study, the crack, plastic deformation, IRI, and SPI values measured using the existing RoadScanner of a corresponding section, as well as the relative dielectric constant values of a lower deck measured using a ground penetrating radar are reduced. The results of a small impact load test are verified by comparing the modulus of elasticity measured. RESULTS : In the Hongjecheon Overpass, when comparing the suspicion points of deterioration between the center of the lane and the 25 measurement data points of the wheel pass section based on the elastic modulus of the light falling weight deflectometer (LFWD), it is discovered that the lane comprises four centers (16%) and 18 wheelpaths (72%). The percentage of suspected deterioration points in the center is higher than that in the wheelpath. In addition, in the case of the Seoho Bridge, by comparing the suspicious points of deterioration for 11 measurement data points in the middle of the lane and the wheelpath section based on the elastic modulus of the LFWD, it is discovered that five points (45%) in both the middle of the lane and the wheel pass are similar. CONCLUSIONS : In this study, a comparative analysis of the LFWD elastic modulus and SPI factors (crack rate, plastic deformation, and IRI) of the Hongjecheon Overpass and Seoho Bridge is conducted to confirm the factors of pavement breakage. Among them, it is confirmed that it affects the pavement condition the most; however, to consider the LFWD elastic modulus as an evaluation criterion for future structure pavement, the data points must be verified via additional experiments to ensure high reliability.

PURPOSES : The purpose of this study was to develop the evaluation methodologies for spraying amount and sprayed condition of curing compound based on IoT technology when concrete pavements are constructed. METHODS : To measure the spraying amount of curing compound, a turbine type flowmeter was selected and a number of laboratory experiments were performed to verify the applicability of the selected sensor. To evaluate the uniformity of the sprayed curing compound on the concrete pavement surface, image process technologies were examined using pictures taken from the actual construction sites and from the test specimens. RESULTS : By performing experiments using water and curing compound, the selected flowmeter was verified to properly be applied to measure the spraying amount of curing compound with an acceptable accuracy. By conducting image processing using pictures of the sprayed curing compound on the concrete pavement surface, it was found that the 8 color analysis method was the best to evaluate the uniformity of the sprayed curing compound. CONCLUSIONS : From this study, it was concluded that the spraying amount of curing compound could be accurately measured using a turbine type flowmeter and the uniformity of the sprayed curing compound on the concrete pavement surface could be properly evaluated using an image processing technology.

PURPOSES : The purpose of this study is to enhance the reliability of artificial intelligence for a noise-based pavement condition rating system (to a target performance of 95 %). METHODS : By comparing four types of pattern recognition artificial intelligence, this work acquires high-quality learning data and optimizes data learning through analysis of error characteristics. RESULTS : The system reliability improved up to 97 % (82 % in a prior study). In addition, 100 % was achieved for the E(F) condition grade, which has a direct impact on maintenance decision making. CONCLUSIONS : KNN-DTW (K-nearest neighbor dynamic time warping) is judged to be the most suitable type of artificial intelligence for a noise-based pavement condition rating system; a 4-grade system is the most suitable for classifying pavement condition.