본 연구에서는 어장환경평가가 수행된 어류가두리 양식장의 조사 결과 중 일부를 대상으로 저서동물지수(Benthic Health Index, BHI)를 이용하여 양식장의 건강도를 평가하였으며, 평가 결과로 산출된 각 등급의 양식장 환경 특성을 파악하였다. 평가대상 어류가두리 양식장은 동해, 서해, 남해에 위치한 43개 양식장으로, BHI 1등급은 8개 양식장, 2등급은 4개 양식장, 3등급은 12개 양식장, 4등급은 19개 양식장이 포함되었다. 1등급 어류가두리양식장은 사질 퇴적상, 양식강도가 낮은 양식장이 포함되었으며, 2등급 어류가두리양식장은 해수 유통이 원활한 해역에 위치한 양식장이 속하였다. 3, 4등급이 속한 어류가두리양식장은 높은 강도로 양식 활동이 진행되고 있는 대다수의 양식장이 포함되었다. 3등급과 4등급의 양식장은 총유기탄소는 큰 차이가 없었으나, 다모류 군집분석의 결과는 4등급의 양식장에서의 유 기물 농축이 더 높은 것으로 나타났다.

We investigated physicochemical properties and isotopic compositions of organic matter (δ13CTOC and δ15NTN) in the old fish farming (OFF) site after the cessation of aquaculture farming. Based on this approach, our objective is to determine the organic matter origin and their relative contributions preserved at sediments of fish farming. Temporal and spatial distribution of particulate and sinking organic matter (OFF sites: 2.0 to 3.3 mg L-1 for particulate matter concentration, 18.8 to 246.6 g m-2 day-1 for sinking organic matter rate, control sites: 2.0 to 3.5 mg L-1 for particulate matter concentration, 25.5 to 129.4 g m-2 day-1 for sinking organic matter rate) between both sites showed significant difference along seasonal precipitations. In contrast to variations of δ13CTOC and δ15NTN values at water columns, these isotopic compositions (OFF sites: -21.5‰ to - 20.4‰ for δ13CTOC, 6.0‰ to 7.6‰ for δ15NTN, control sites: - 21.6‰ to - 21.0‰ for δ13CTOC, 6.6‰ to 8.0‰ for δ15NTN) investigated at sediments have distinctive isotopic patterns (p<0.05) for seawater-derived nitrogen sources, indicating the increased input of aquaculture-derived sources (e.g., fish fecal). With respect to past fish farming activities, representative sources (e.g., fish fecal and algae) between both sites showed significant difference (p<0.05), confirming predominant contribution (55.9±4.6%) of fish fecal within OFF sites. Thus, our results may determine specific controlling factor for sustainable use of fish farming sites by estimating the discriminative contributions of organic matter between both sites.

This study is aimed to figure out the productivity and variability of cage-aquaculture changes. According to the analysis, the productivity of major fish species has been increasing, except mullet. Although the regional productivity has decreased in the last two years, it has been on the rise considering as a whole. Gyeongsangnam-do showed the highest level of productivity by region. Productivity by species was also higher than other regions in the cases of rock fish, mullet and sea bream followed by productivity of Chungcheongnam-do. The production of marine cage-culture in Jeollanam-do is the second largest in Korea in value/weight while its productivity is lower than that of Chungcheongnam-do. When it comes to comparison by region, Gyeongsangnam-do shows the lowest productivity variation. And Jeollanam-do shows the second-lowest variation in productivity that is only about half of that of Chungcheongnam-do province. Thus, it is found that Jeollanam-do region has an advantage in management stability while its productivity is low. On the other hand, productivity by species was also analyzed. Gyeongsangnam-do has the highest productivity by species for rock fish, mullet and sea bream whereas rock bream productivity is the highest in Jeollanam-do. Therefore, it probably needs to reflect these results when choosing regional-focused incubation fish species.

This study is aimed to analyze the economic feasibility of yellowtail culture using the copper alloy net cage in Gyeongsangbuk-do. First of all, in order to evaluate the copper alloy net cage on yellowtail culture, I review the trend on the yellowtail culture industry and research the concept of copper alloy net cage. The copper-alloy net cage is now recognized as an advantages of its system stability, recycling, antibiosis and food safety. The results were summarized as follows: first, there was significant meaning of the profit model of yellowtail culture by the price difference. Second, I analyzed in the economic feasibility of yellowtail culture using the copper alloy net cage, internal rate of return (IRR) was 51.58%, a benefit-cost ratio was shown to be 2.27 and net present value (NPV) was 1,087,337 thousand won, which indicates the economic feasibility of yellowtail culture using the copper alloy net cage is profitable. Finally, in order to improve the economic valuation, it is necessary to focus more on the developing of technology and cost reduction strategy on the copper alloy net cage.

양식업이 발달한 통영 오비도 주변해역에서 하계 해양환경요인의 변화 특성과 그에 따른 식물 플랑크톤의 변화양상을 파악하여, 가두리 양식 생물에 미칠 수 있는 잠재적인 환경요인을 분석 하였다. 조사는 2개의 정점에서 2016년 6월부터 9월까지 격주로 4개월간 수행되었다. 6월과 7월은 강한 수온 성층이 형성되었으며, 8월에는 특이적으로 강한 양쯔강 희석수의 영향으로 8월 10일 29℃ 전후로 고수온이 관찰되었다. 조사기간 동안 질산염+아질산염, 암모늄, 인산염, 규산염은 각각 0.08~5.11 μM, 0.08~34.62 μM, 0.01~ 1.15 μM, 1.46~31.79 μM의 범위를 보였다. Chlorophyll a 농도는 0.49~7.39 μg l-1의 범위를 보였다. 9월의 빈번한 잦은 강우 및 양식어장에 서 용출된 영양염류는 장시간 지속되지 못하고 빠르게 소비되거나 확산되었다. 이후 강우로 인한 영양염 유입과 함께 표층을 중심으로 Chaetoceros debilis, C. pseudocurvisetus, Pseudonitzschia delicatissima와 같은 규조류가 최대 4.74 × 109 cells l-1로 크게 증식하였다. 또한 용 존산소 변동은 4.52~7.62 μg l-1로 식물플랑크톤 대증식 이후 조사에서 유기물질이 분해됨에도 불구하고 빈산소 수괴(< 4.00 mg l-1)의 형성은 관찰되지 않았다. 따라서 본 해역은 하계의 식물 플랑크톤 증식 및 가두리양식장이 밀집됨에도 불구하고, 다른 반폐쇄적 만과 달리 해류 순환 이 원활한 특징으로 인해 빈산소 수괴는 나타나지 않았다.

Mobile fish-cage was developed assuming a cage net with an enclosed area, which and estimated the hydrodynamic characteristics of the cage through the model experiment. Flux-shielding plates, installed in the bow were compared with the resistance test carried out by making a hole, bilge keel and stud, and basic block flow rate consisting of the results to a flat surface plate. The experimental results confirmed the improved resistance performance effect of 3~6% in the bilge keel and the stud form. To assess the stability of the fish-cage, evaluation of the stability in accordance with the stability criteria for determining the floating docks had confirmed that it satisfied the static stability performance under operating conditions at sea.

The sea cage in marine aquaculture might be varied such as on the stability and shape in the open sea by environmental factors. To evaluate the stability of net cage structures in the open sea, the physical and numerical modeling techniques were applied and compared with field observations. This study was carried out to analyse the stability and the volume loss which would have an effect on the fish swimming behavior in the octagonal pillar type fish cage under the open sea. As a results, the volume loss ratio of the fish cage as measured using a depth sensor was indicated a value of the 30.3% under the current velocity (1.1m/s). The fish cage should be consisted of a concrete block with a weight over 10 tons, a mooring rope diameter over 28mm PP, and a shackle of 25mm under the current speed of 1m/sec for reasonable stability.

Nowadays, consumption of fisheries products is increasing. There are several factors, one of which is a quantitative development through aquaculture. Another factor is an increase qualitative consumption of fish which require that fish be supplied alive. This requires a lot of technical effort to transport the live fish that have low survival rate (c.f. tuna and mackerel) in coastal waters and in the open sea. To develop a towing cage for transporting the live fish, model test in a circulate water channel and simulation by computer tool were carried out. In order to spread vertically, floats were attached at the upper part of the cage, and iron chains attached at the lower part of the cage. For horizontal spreading, kites were attached on the cage. The tension and spreading performance of the cage were measured. The result shows that the tension and reduction ratio of inside volume of the cage were tended to increase with increased towing speeds. The suitable operation condition in towing cage was 1.0 m/s towing speeds with vertical spreading force 8.7 kN, horizontal spreading force 5.6 kN; in this case the reduction ratio of inside volume of the cage was estimated as 25%.

This study aims to analyze the performance of a submersible fish cage which was designed for developing an economical cage system can be applied in korean aquaculture environment easily. To analyze the performance of the designed cage a model test was carried out. In the test, inclination changes of the upper frame and mooring tensions of model cage were measured during the submerging and surfacing motion in still water and wave condition (period: 2s, wave height: 0.1, 0.2, 0.3m). As a result, in the still water condition the model cage kept horizontal balance and inclination degree of the upper frame was about 1˚. In the wave condition, the model cage showed bilateral symmetric up-and-down motion but the average inclination degree of the upper frame was about 0˚. When the model cage reached at a depth of 1m, the up-and-down motion of the cage was decreased by 12% compared with that of at the surface (period 2s, height 0.3m). In the same wave condition, the maximum and average line tension under the bottom position were about 8% and 11% respectively compared with that of at surface.

Simulation technique for the fish behavior was applied to estimate fish school movement in the cage net. Individual-based fish behavior model (Huth and Wessel, 1991) was evaluated in a free area to understand the characteristics for the model, and the movement in the cage net was simulated by defining the fish reaction against the displacement of cage net. As a result, the distance to the net was not considerably changed and the space among fishes in cage net was slightly decreased by reducing the net space. Swimming area was, however, significantly affected by changing the net space and the relationship between swimming area and net displacement was theoretically estimated as y=-0.21x+1.02 (R2=0.96). these results leads the conclusion that individual-based model was appropriated to describe the fish school reaction in the cage net and be able to use for evaluating the influence on cultured fish.

In this research, the submersible fish cage was designed to avoid structural and biological damage during harsh sea conditions. The submersible cage system consists of netting, mooring ropes, a floating collar, floats, sinkers and anchors. Whole elements of the cage were modeled on the mass-spring model. The computer simulations were carried out to investigate the dynamic behavior of the cage and to calculate mooring line tension subjected to tidal currents and waves. As expected, the tension values in the mooring line of the submerged position are 36% less compared to that of the surface cage under the same loading conditions. As the wave was used in combination with the current velocity of 1m/s, the average tensile load for the submerged cage showed 85% of the value for the floating cage. The simulation results provide an improved understanding of the behaviors of the structure and valuable information on the optimized design of the cage system exposed to open ocean environmental factors.

Numerical modeling was used to evaluate the submerging characteristics of the submersible fish cage system operated by compressed air. The submerging characteristics calculated by numerical analysis as the cage was moved up and down were nearly identical to existing experiment results. Thus, the numerical model proposed in this study could be very useful in analyzing various parameters required for optimizing the design of a submersible fish cage system operated by compressed air.

규칙파와 불규칙파 및 흐름이 함께 작용하는 상태에 놓인 가두리 시설에 대해 작용 유체력을 가두리 시설의 부설 방향별로 해석하기 위하여, 정사각형 모형 가두리 시설과 원형 모형 가두리 시설을 대상으로 예인 수조에서 수리 모형 실험을 실시하였다. 실험에서 얻어진 결과를 요약하면 다음과 같다. 1. 규칙파를 받고 있는 정사각형 가두리 시설에 작용하는 유체력은 가두리 시설의 부설 방향별로 큰 차이를 보이지 않았다. 2. 불규칙파와 흐름을 동시에 받고 있는 가두리시설에 작용하는 파력 에너지의 피크 주파수는 파의 그것과 잘 일치하였고, 작용 유체력은 정사각형 가두리 시설보다 원형 가두리 시설에서 더 작았다. 3. 가두리 시설의 안정성에서 있어서는 그 구조가 원형인 것이 정사각형인 것보다 나은 편이었다.

To develop a new fish cage which is required for offshore or moving cage culturing system has been gradually increased against being closely dense of fish cage in shallow water. Though submersible fish cage culturing system is essential technology for converting from shallow water into the offshore, it was pointed out the serious problem about stability of which are sinking and floating state. This study is presented conceptual design of submersible fish cage centered with a mooring steel pile to acquire stability and faculty. Design of mooring steel pile for submersible fish cage culturing system needs to carry out optimal design of mooring steel pile for which much efforts are required. Formulation and optimal design process of submersible fish cage are organized into using Sequential Quadratic Programming method of numerical optimization. For submersible fish cage system centered with a mooring steel pile, process of the optimal design is proposed and the optimal solutions are obtained