This study improved the work efficiency by supplementing the shortcomings of the manual process by developing a double tube feeding device, and the following results were obtained by conducting the production capacity, production length, and defect rate tests. Developed a double tube production system to enable the simultaneous production of two tubes, increasing the production volume by about 1.5 times. The product length has been improved from semi-automatic to automated, and the production capacity has been improved from 16 to 25 pieces per hour (based on 15m). Developed a double-tube input straight line automatic adjustment feeder, which resulted in reducing the defect rate to less than 1%.

In this study, the performance was checked and the optimal conditions were found by machining the inner surface of a round pipe using the magnetic abrasive finishing method. In this experiment, an AL 6063 pipe was used as a sample. To check the performance of magnetic abrasive finising, the machining effect of different abrasive particle mixing ratio, rotation speed, and magnetic pole arrangement was analyzed through surface roughness (Ra) and weight removal measurement. The optimum mixing ratio was 3:1 of electrolytic iron to magnetic abrasive particles, the rotational speed was 1600rpm, and the best surface roughness was obtained in the N-S-N arrangement of magnetic poles.

This is to develop a micro water turbine which makes some power from just a fluid velocity in the water pipe. While power is produced from impulsive force which generated by a high head in the case of existing water turbine, this is to produce a power from rotating force of helical turbine which rotated by fluid velocity in the water pipe. Some results of analysis fluid pattern at turbine blade for design shows that bubble is generated from turbulence surrounding blade and pulsatory motion generated as fluid being blocked and opened by blade due to turbine structure. This two phenomena cause to lower power production efficiency and shorten turbine durability. So this is studied to minimize bubble generation and pulsation for optimizing design of turbine blade. Therefore it is determined that the number of blade is three, geometric form of blade is NACA 4420 and angle of blade is 30 degree. An experiment equipment of water turbine is manufactured on the base of these factors(NACA 4420, angle 30。). It is obtained that power production of turbine increases in proportion to velocity which is changed from 1.7 m/sec to 3.5 m/sec. When fluid velocity is 1.7m/sec the power production of turbine is 355W. Power production increase continuously as increasing the fluid velocity and power is 2kW on 3m/sec of fluid velocity.

The performance of helical hydro turbine in water pipe line depends on the sectional shape of turbine blade, pitch angle of turbine blade, solidity and number of turbine blades, To investigate the effects of these design factors on the performance of helical hydro turbine, flow analysis was carried out by using commercial code ANSYS CFX version 14..5. From CFD analysis we obtained the optimum design factors which were the asymmetric blade shape of NACA4420, the pitch angle of 15 degrees and the solidity of 0.3. These results can be used for the actual design of sphere-shaped helical turbine in water pipe line.

OTEC(Ocean Thermal Energy Conversion) system using the temperature difference between cooler deep and surface ocean waters is one of the renewable energy. But in Korea, OTEC system can not apply except in winter because surface sea water temperature is not enough. C-OTEC(Combined OTEC) system is that utilizes temperature difference between sea water and the condenser of power plants via working fluid. It can be a good alternative in the warm surface sea water for Mid-latitudes region like Korea. In this study, a marine survey using multi-beam echo sounder, single-beam echo sounder and sparker seismic wave is performed and sea water intake pipe line is proposed for the 10kW C-OTEC Pilot Plant.

OO상수도 매설관로 주요 불탐구간의 매설환경 조건은 고압송유관, 광케이블, 전력선, 도시가스관 등 주변지장물의 전자기장 간섭이나 도로 성토에 따른 토피고 증가 및 주변 굴착공사에 따른 접근 불가 등의 상태이므로, 관로 유지관리를 위하여 직접적인 조사 등을 실시할 필요가 있는 것으로 판단된다.