Spent nuclear fuel (SNF) characterization is important in terms of nuclear safety and safeguards. Regardless of whether SNF is waste or energy resource, the International Atomic Energy Agency (IAEA) Specific Safety Guide-15 states that the storage requirements of SNF comply with IAEA General Safety Requirement Part 5 (GSR Part 5) for predisposal management of radioactive waste. GSR Part 5 requires a classifying and characterizing of radioactive waste at various steps of predisposal management. Accordingly, SNF fuel should be stored/handled as accurately characterized in the storage stage before permanent disposal. Appropriate characterization methods must exist to meet the above requirements. The characterization of SNF is basically performed through destructive analysis/non-destructive analysis in addition to the calculation based on the reactor operation history. Burnup, Initial enrichment, and Cooling time (BIC) are the primary identification targets for SNF fuel characterization, and the analysis mainly uses the correlation identified between the BIC set and the other SNF characteristics (e.g., Burnup - neutron emission rate) for characterizing. So further identification of the correlation among SNF characteristics will be the basis for proposing a new analysis method. Therefore, we aimed to simulate a SNF assembly with varying burnup, initial enrichment, and cooling time, then correlate other SNF properties with BIC sets, and identify correlations available for SNF characterization. In this study, the ‘CE 16×16’ type assembly was simulated using the SCALEORIGAMI code by changing the BIC set, and decay heat, radiation emission characteristics, and nuclide inventory of the assembly were calculated. After that, it was analyzed how these characteristics change according to the change in the BIC set. This study is expected to be the basic data for proposing new method for characterizing the SNF assembly of PWR.

Flow-induced vibration can lead to fretting wear damage of fuel rods and spacer grids in nuclear reactors. Similarly, during the transport of spent nuclear fuel assemblies, continuous vibration and intermittent impact might also result in fretting wear due to dynamic interaction. Therefore, it is important to evaluate fuel rod damage due to fretting wear under such transport conditions. This study examines spent nuclear fuel rod specimens fabricated with hydride cladding tubes and simulated pellets, with hydrogen content ranging from 200 to 700 ppm and oxide film thickness ranging from 25 to 100 micrometers. Tests were conducted under a worst-case scenario, assuming continuous exposure to that condition during the expected transport time. Results indicate that the wear depth of all rod specimens occurred within the oxide film, suggesting a high resistance to fretting wear during transportation.

The Comprehensive Analyzer of Real Estimation for spent fuel POOL (CAREPOOL) has been developed for evaluating the thermal safety of a spent nuclear fuel pool (SFP) during the normal and accident conditions. The management of spent nuclear fuel function provides a management tool for spent nuclear fuel in the SFP. The fuel assemblies both in SFP and reactor side can be shown graphically in the screen. The loading sequence into transfer cask can be checked respectively in the CAREPOOL. A basic heat balance equation was used to estimate the SFP temperature using the heat load calculated in the previous step. The characteristics of typical SFPs and associated cooling systems at reactor sites in the Korea were applied. Accident simulation like station black out leading to loss of SFP cooling or inventory is possible. Emergency cooling water injection pipe installed subsequent to the events at Fukushima 2011 is also modeled in this system. The CAREPOOL provides four main functions- management of spent nuclear fuel, decay heat calculation by ORIGEN-S code, estimation of the time to boil/fuel uncovering by thermal-hydraulics calculations, fuel selection for periodic spent fuel transferring campaign. All of these are integrated into the GUI based CAREPOOL system. The CAREPOOL would be very beneficial to nuclear power plant operator and trainee who have responsibility for the SFP operation.

There have been a variety of issues related to spent nuclear fuel in Korea recently. Most of the issues are related to intermediate storage and disposal of spent nuclear fuel. However, recently, various studies have been started in advanced nuclear countries such as the United States to reduce spent nuclear fuel, focusing on measures to reduce spent nuclear fuel. In this study, a simple preliminary assessment of the thermal part was performed for the consolidation storage method which separates fuel rods from spent nuclear fuel and stores them. The preliminary thermal evaluation was analyzed separately for storing the spent fuel in fuel assembly state and separating the fuel rods and storing them. The consolidation storage method in separating the fuel rods was advantageous in terms of thermal conductivity. However, detailed evaluation should be performed considering heat transfer by convection and vessel shape when storing multiple fuel bundles simultaneously.

In Korea, the construction of dry storage facilities for spent nuclear fuel is being promoted through the 2nd basic plan for high-level radioactive waste management. When operating dry storage facilities, exposure dose assessment for workers should be performed, and for this, exposure scenarios based on work procedures should be derived prior. However, the dry storage method has not yet been sufficiently established in Korea, so the work procedure has not been established. Therefore, research is needed to apply it domestically based on the analysis of spent nuclear fuel management methods in major overseas leading countries. In this study, the procedure for receiving and storing spent nuclear fuel in a concrete overpack-based storage facility was analyzed. Among the various spent nuclear fuel management systems, the metal overpack-based HI-STAR 100 system and the concrete overpackbased HI-STORM 100 system are quite common methods in the United States. Therefore, in this study, work procedures were analyzed based on each final safety analysis report. First, the HI-STAR 100 overpack enters the facility and is placed in the transfer area. Remove the impact limiter of the overpack and install the alignment device on the top of the overpack. Place the HI-TRAC, an on-site transfer device, on top of the alignment unit and remove the lids of the two devices to insert the canister into the HI-TRAC. When the canister transfer is complete, reseat the lid to seal it, and disconnect the HI-TRAC from the HI-STAR 100. Raise the canister-loaded HI-TRAC over the alignment device on the top of the HI-STORM 100 overpack and remove the lids of the two devices that are in contact. Insert the canister into the HI-STORM 100 and reseat the lid. The HI-STORM 100 loaded with spent nuclear fuel is transferred to the designated storage area. In this study, the procedure for receiving and storing spent nuclear fuel in a concrete overpack-based storage facility was analyzed. The main procedure was the transfer of canisters between overpacks, and it was confirmed that HI-TRAC was used in the work procedure. The results of this study can be used as basic data for evaluating the exposure dose of operating workers for the construction of dry storage facilities in Korea.

Once systems, structures and components (SSCs) of dry storage systems are classified with respect to safety function or safety significance (i.e., safety classification), appropriate engineering rules can be applied to ensure that they are designed, manufactured, maintained, managed (e.g. aging management) etc. In Unites States, the systems, structures and components (SSCs) consisting DSSs are classified into two or several grades (i.e., class A, B and C or not important to safety, and important to safety (ITS) or not important to safety (NITS)) with respect to intended safety function and safety significance. This classification methods were based on Regulatory Guide 7.10 (i.e., guidance for use in developing quality assurance programs for packaging). Also, in Korea, SSCs of DSSs should be classified into ITS and NITS in much the same as method based on Regulatory Guide 7.10. In that guidance, for providing graded approach to manage the SSCs of packaging, they were trying to classifying SSCs in accordance with radiological consequences. But there was limitations that the provided classification criteria was still qualitative, so that it was not enough for managing the SSCs according to graded approach. On the other hand, in some other nuclear facilities (i.e., nuclear power plant, radioactive waste management facility and disposal facility etc.), quantitative criteria relevant to radiological consequence (i.e., radiation doses to workers or to the public) or inventory of radioactivity are existed so that it can be applied for classifying safety classes. In summary, the study on the application safety classification that applied quantitative criteria to perform safety classification of SSCs in DSS is inadequate or insufficient. The purpose of this study is proposing the preliminary framework for estimating safety significance of SSCs in DSS which can be utilized in our further advanced studies. In this study, a framework was established to estimate the safety significance of SSCs related to radiation shielding and confinement using MCNP® 6.2 and Microsoft Excel. Referring to the methodology of IAEA Specific Safety Guide 30, we assumed severity for failures of components that could lead to degradation of the SSC’s performance. The safety class of SSC was decided based on the impact of SSC’s failure on consequences.

As temporary storage facilities for spent nuclear fuel (SNF) are becoming saturated, there is a growing interest in finding solutions for treating SNF, which is recognized as an urgent task. Although direct disposal is a common method for handling SNF, it results in the entire fuel assembly being classified as high-level waste, which increases the burden of disposal. Therefore, it is necessary to develop SNF treatment technologies that can minimize the disposal burden while improving long-term storage safety, and this requires continuous efforts from a national policy perspective. In this context, this study focused on reducing the volume of high-level waste from light water reactor fuel by separating uranium, which represents the majority of SNF. We confirmed the chlorination characteristics of uranium (U), rare earth (RE), and strontium (Sr) oxides with ammonium chloride (NH4Cl) in previous study. Therefore, we prepared U-RE-SrOx simulated fuel by pelletizing each elements which was sintered at high temperature. The sintered fuel was again powdered by heating under air environment. The powdered fuel was reacted with NH4Cl to selectively chlorinate the RE and Sr elements for the separation. We will share and discuss the detailed results of our study.

A radiation shielding resin with thermal stability and high radiation shielding effect has been developed for the neutron shielding resin filled in the shielding shell of dry storage/transport cask for spent nuclear fuel. Among the most commercially available neutron shielding resins, epoxy and aluminum hydroxide boron carbide are used. But in case of the resin, hydrogen content enhances the neutron shielding effect through optimization of aluminum hydroxide, zinc borate, boron carbide, and flame retardant. We developed a radiation shielding material that can increase the boron content and have thermal stability. Flame retardancy was evaluated for thermal stability, and neutron shielding evaluation was conducted in a research reactor to prove the shielding effect. As a result of the UL94 vertical burning test, a grade of V-0 was received. Therefore, it was confirmed that it had flame retardancy. According to an experiment to measure the shielding rate of the resin against neutron rays using NRF (Neutron Radiography Facility), a shielding rate of 91.54% was confirmed for the existing resin composition and a shielding rate of 96.30% for the developed resin composition. A 40 M SANS (40 M Small Angle Neutron Scattering Instrument) neutron shielding rate test was performed. Assuming aging conditions (6 hours, 180 degrees), the shielding rate was analyzed after heating. As a result of the experiment, the developed products with 99.8740% and 99.9644% showed the same or higher performance.

One of the most important factors in the delivery and acceptance requirements for dry storage of spent fuel is the burnup of spent fuel. Here, burnup has a unit of MWD/MTU and is used as a measure of how much nuclear fuel is depleted in a nuclear reactor. In addition, since it is one of the most basic characteristic information for the soundness evaluation of spent nuclear fuel, it is a required item not only by regulatory agencies but also by KORAD, the acquiring agency. The burnup of spent nuclear fuel is the burnup calculated through flux mapping using signals measured from in-reactor instruments during nuclear power plant operation (hereinafter: actual burnup) and the burnup calculated using the core design code (hereinafter: design burnup). In this paper, the design burnup of spent nuclear fuel discharged from OPR100 NPPs (Nuclear Power Plants) in Korea was recalculated to confirm the reliability of the actual burnup currently managed at the nuclear power plant. Basically, since spent nuclear fuel must maintain subcriticality under wet storage or dry storage, a burnup error of about 5% is considered as a conservative approach when evaluating the criticality safety of wet storage tanks and dry storage systems. Therefore, in this paper, we tried to verify whether the difference between actual burnup and design burnup for all spent nuclear fuel released from domestic OPR100 type light water reactor nuclear power plants is within 5%. As a result of the evaluation, the largest deviation between actual burnup and design burnup was about 1,457 MWD/MTU, and when converted into a percentage, it was about 3.3%. Therefore, it was confirmed that the actual burnup managed by OPR1000 NPPs in Korea has sufficient reliability. In the future, we plan to check the reliability of the performance burnup managed in WH NPPs, and some of them will be verified through measurement.

Al-B4C neutron absorbers are currently widely used to maintain the subcriticality of both wet and dry storage facilities of spent nuclear fuel (SNF), thus long-term and high-temperature material integrity of the absorbers has to be guaranteed for the expected operation periods of those facilities. Surface corrosion solely has been the main issue for the absorber performance and safety; however, the possibility of irradiation-assisted degradation has been recently suggested from an investigation on Al-B4C surveillance coupons used in a Korean spent nuclear fuel pool (SFP). Larger radiation damage than expectation was speculated to be induced from 10B(n, α)7Li reactions, which emit about a MeV α-particles and Li ions. In this study, we experimentally emulated the radiation damage accumulated in an Al-B4C neutron absorber utilizing heavy-ion accelerator. The absorber specimens were irradiated with He ions at various estimated system temperatures for a model SNF storage facility (room temperature, 150, 270, and 400°C). Through the in-situ heated ion irradiation, three exponentially increasing level of radiation damages (0.01, 0.1, and 1 dpa or displacement per atom) were achieved to compare differential gas bubble formation at near surface of the absorber, which could cause premature absorber corrosion and subsequential 10B loss in an SNF storage system. An extremely high radiation damage (10 dpa), which is unlikely achievable during a dry storage period, was also emulated through high temperature irradiation (350°C) to further test the radiation resistance of the absorber, conservatively. The irradiated specimens were characterized using HR-TEM and the average size and number density of radiation-induced He bubbles were measured from the obtained bright field (BF) TEM micrographs. Measured helium bubble sizes tend to increase with increasing system (or irradiation) temperature while decrease in their number density. Helium bubbles were found from even the lowest radiation damage specimens (0.01 dpa). Bubble coalescence was significant at grain boundaries and the irradiated specimen morphology was particularly similar with the bubble morphology observed at the interface between aluminum alloy matrix and B4C particle of the surveillance coupons. These characterized irradiated specimens will be used for the corrosion test with high-temperature humid gas to further study the irradiation-assisted degradation mechanism of the absorber in dry SNF storage system.

In the event of a loss of a SNF (spent nuclear fuel) transport cask during maritime transportation, it is essential to evaluate the critical depth at which the integrity of the cask can be maintained under high water pressure. SNF transport casks are classified as Type B containers and the integrity of of the containment boundary must be maintained up to a depth of 200 meters unless the containment boundary was breached under beyond-design basis accidents. However, if an intact SNF cask is lost at a depth deeper than 200-meter, release of radioactive material may occur due to breach of containment boundary with over-pressure. In this study, we developed a code for the evaluation of the pressure limit of SNF transport cask, which can be evaluated by inputting the main dimensions and loading conditions of cask. The evaluation model was coded as a computer module for ease of use. In the previous study, models with three different fidelities were developed to ensure the reliability of the calculation and maintain sufficient flexibility to deal with various input conditions. Those three models consisted of a high-fidelity model that provided the most realistic response, a low-fidelity model with parameterized simplified geometry, and a mathematical model based on the shell theory. The maximum stress evaluation of the three models confirmed that the mathematical model provides the most conservative results than the other two models. The previous results demonstrate that mathematical models can be used in the code of computer modules. In this study, additional models of transport cask were created using parametric modeling techniques to improve the accuracy of the pressure limit assessment code for different cask and situations. The same boundary conditions and loading conditions were imposed as in the previous simplified model, and the maximum stress results considering the change in the shape of the transport container were derived and compared with the mathematical model. The comparison results showed that the mathematical model had more conservative values than the simplified model even under various input conditions. Accordingly, we applied the mathematical model to develop a transportation container pressure limit evaluation code that can be simulated in various situations such as shape change and various situations.

Long-term safe storage of spent nuclear fuel (SNF) determines sustainability of the current light water reactor (LWR) fleet. In the U.S., SNF is stored in stainless steel canister in dry cask storage system (DCSS) after spending several years in wet pool storage system while there is no DSCC in Republic of Korea. The SNF storage time in DSCC is expected to be multiple decades since no permanent geological repositories are identified in both countries. One limiting factor for extended storage of SNF in DSCC is chloride-induced stress corrosion cracking (CISCC) in the welded regions of the stainless steel canisters. The propensity for the occurrence of CISCC has warranted the development of the mitigation and repair technologies to ensure the safe and long-term storage for both present and new canister although no CISCC failure was reported yet. This study investigates cold spray deposition coatings of 304 L and 316 L stainless steels on prototypical stainless steel canisters such as sensitized flat and C-ring samples. The cold spray technology has been identified as the most promising approach by Extended Storage Collaboration Program (ESCP) driven by Electric Power Research Institute (EPRI). The talk includes microstructural characterization, adhesion strength measurement, residual stress evaluation, and corrosion behavior of the coated materials in boiling MgCl2 solution and electrochemical corrosion tests in NaCl solution. In addition, the capability of repair of cracks on the canister surface using the coating technology will be presented.

Nuclear inspection is necessary to verify nuclear activities. If North Korea takes denuclearization, North Korea’s nuclear materials should be verified through non-destructive testing and destructive testing for nuclear material production. Since destructive testing of all substances is impossible, nondestructive testing is essential. Most non-destructive tests are performed by measuring the energy of gamma rays, but the characteristics of nuclear fuel can be evaluated by measuring neutron sources when enclosed with thick shields and when shielding structures are difficult to remove. Before the neutron source evaluation of MAGNOX used by North Korea, the relative characteristics will be evaluated later by analyzing the burnup, enrichment, and cooling time of the spent nuclear fuels discharged from the domestic nuclear power plant. This study evaluated the source strength and major nuclides according to burnup for the WH17×17 nuclear fuel assembly. The depletion calculation was conducted using SCALE 6.2 ORIGEN, and 3.5wt% enrichment, 10, 20, 30, 40, 50, 60 MWd/kg burnup, and five years cooling time, the minimum requirement for transport specified in the notice of the Nuclear Safety Commission, was applied. Although the impact assessment on enrichment should be evaluated with MCNP Tally to consider the fission reaction of the generated neutrons, this study only evaluated the spontaneous fission and (a, n) reactions that occurred first because it only evaluates the burnup impact. As burnup increased, neutron generation increased, and most of the total neutron strength occurred through spontaneous fission from the 10 MWd/kg burnup step. The influence of Pu-240 nuclides was dominant in the 10 MWd/kg burnup step but most neutrons were generated in tiny amounts of Cm- 244 generated from 20 MWd/kg burnup. Since DPRK’s 5 MWe Yongbyon MAGNOX has very low burnup (about 0.7 MWd/kg), the primary neutron sources of 10 MWd/kg, Am-241 and Pu isotopes, especially Pu-240, are expected to be used as indicators for evaluating spent nuclear fuel characteristics. If only specific nuclides are evaluated as major neutron sources at lower burnup than those evaluated in this study, in that case, the accuracy of non-destructive testing can be improved. Additionally, the evaluation according to the enrichment and cooling time should be considered as well.

The disposal of spent nuclear fuel (SNF) poses a significant challenge due to its high radioactivity and heat generation. However, SNF contains reusable materials, such as uranium and trans-uranium, which can be recovered through aqueous reprocessing or pyrochemical processes. Prior to these processes, voloxidation is necessary to increase reaction kinetics by separating fuels from cladding and reducing the particle size. In the voloxidation, uranium dioxide (UO2) from SNF is heated in the presence of oxygen and oxidized to triuranium octoxide (U3O8), resulting a release of gaseous fission products (FPs), including technetium-99 (Tc-99), which poses a risk to human health and the environment due to its high mobility and long half-life of 2.1×105. To date, various methods have been developed to capture Tc in aqueous solutions. However, a means to capture the gaseous form of Tc (Tc2O7) is essential in the voloxidation. Due to the radioactive properties of technetium isotopes, rhenium is often used as a substitute in laboratory settings. The chemical properties of rhenium and technetium, such as their electronic configurations, oxidation states, and atomic radii, are similar and these similarities indicates that the adsorption mechanism for rhenium can be analogous to that for technetium. In the previous study, a disk-type adsorbent based on CaO developed was effective in capturing Re. However, this study lacked sufficient data on the chemical properties and capture performance of the adsorbent. Furthermore, the fabrication of disk-type adsorbents is time-consuming and requires multiple steps, making it impractical for mass production. This study introduces a simple and practical method for preparing CaO-based pellets, which can be used as an adsorbent to capture Re. The results provide a better understanding of the adsorption behavior of CaO-based pellets and their potential for capturing Tc-99. To the best of our knowledge, this is the first study to apply a CaO-based pellet to capture Re and investigate its potential for capturing Tc-99.

South Korea has been storing UNF in spent fuel pool dry storage facility within Nuclear Power Plants. The dry storage facility of used nuclear fuel (UNF) is essential to sustain safety and sustain stable operation of a nuclear power plant. Most abroad countries have attempted to develop a variety of dry storage facility for used nuclear fuel in order to retain the safe restoration. Many studies have been conducting to safety evaluation for the dry storage facility. However, there is not a ventilation evaluation in the wake of fire event that could influence of the thermal effect on the dry storage facility, even though it will likely to occur fire events such as wildfire, air craft crash. In practice, it happened to catastrophic disaster due to the wild fire adjacent to ul-jin mountain. Also, it happened to fire accident near to the Japonia NPP in Ukraine territory caused of military air plane missile. It has not mostly been studied on the ventilation evaluation considered to thermal safety in the dry storage facility excepted for some researches. It could need the mechanical ventilation systems such as HVAC system in the dry storage system, so that thermal effect can be reduced. In this study, we conducted to the ventilation control modelling by using fire modelling tool (Fire Dynamic Simulator v.6.7). The ventilation scenarios made up for 3 case that can compare flowrate variation with ventilation control. As a result of modelling, there is no differentiation between ventilation control using performance curve with not using performance curve even though the pressure fluctuation would be increased, compared with the case of considering performance curve. Second, it evaluated that the mode for fraction control would occur to pressure rise in the state of controlling the ventilation system flowrate. However, sensitivity of flowrate control was more decreased below less than 5 seconds. Third, in the case of on/off control system revealed more higher resolution than other cases caused by flowrate variation. These results could be considered as the design guidelines for the development dry storage facility to improve the thermal performance that can reduce thermal risk. Furthermore, the study results would expect HVAC system installed in dry storage to help automatic ventilation control relevant to dry storage safety increased.

When the recycling technology of spent nuclear fuels (SNF) for future nuclear reactor systems and the treatment technology of SNF for disposing of in a disposal site use a molten salt such as LiCl-KCl eutectic as a processing medium one of the essential unit processes is a distillation process that remove the salt component mixed with fission products recovered. Especially, in case of Pyro-SFR recycling system the recovered nuclear fuel materials such as U, TRU and some of rare earths come from main three processes (electro-refining, electro-winning, and drawdown processes) for recycling of SNF. These recovered fuel materials contain large portion of molten salt or liquid cadmium which requires removal of them by distillation. In spent nuclear fuels discharged from PWR the portion of composing element is as follows. Uranium is about 95%, other actinides such as transuranic elements (TRU; Np, Pu, Am, Cm) is about 1%, the rare earths (lanthanides) is about 1%, and the other elements is about 3%. For example, americium (Am) in the recovered fuel materials has a problem that the reported loss of Am inevitably occurs during the vacuum salt distillation operation. A new segregation method of AMM (actinide metal mixture)–salt system is based on the difference in melting point of the actinide elements. It is possible to apply this segregation method to recovering other actinides from AMM with accompanied salt because of relatively large amount and lower melting point of a specific element in other actinides avoiding vacuum salt distillation. This new segregation method successfully tested using a surrogate element such as aluminum due to its similar melting point with a specific element. The segregation principle is solid-liquid separation, thus the solidified actinides mixture ingot can take out of a molten salt medium.

After Fukushima nuclear power plant accident in 2011, Concerns about accident of spent fuel pool increase. In Korea, the time of saturation of spent fuel pool is coming, but regulatory measures and safety evaluation are insufficient when occurring spent fuel pool accident. Thus, it is necessary to review of spent fuel pool accident in foreign countries to establish regulatory measures and safety evaluation of spent fuel pool accident suitable for domestic spent fuel pool. Therefore, we reviewed spent fuel pool accident that occurred at Fukushima Unit 4, SONGS Unit 2 and PAKS. In Japan, spent fuel pool accident occurred at Fukushima NPP in 2011. Tsunami was cause of the accident. Station Black Out occurred at Fukushima NPP and Emergency Diesel Generator lost their functions due to Tsunami. As a result, Loss of cooling happened in spent fuel pool at Fukushima NPP. For Unit 4, wall of spent fuel pool in Unit 4 was damaged due to hydrogen explosive, so loss of coolant in spent fuel pool of Unit 4 occurred. After the accident, the temperature of spent fuel pool increases to 75°C, but there was no damage to the spent fuel. In USA, spent fuel pool accident occurred at SONGS Unit 2 in 2013. The debris of nearby ocean is cause of the accident. The debris entered the system through a damaged Salt Water Cooling pump suction strainer. The debris obstructed flow through the Component Cooling Water heat exchanger and operation of Salt Water Cooling. The maximum spent fuel pool temperature during this event was 25.6°C. It was a value that satisfied the technical specifications of the SONGS NPP. In Ukraine, spent fuel pool accident occurred at PAKS in 2003. Unintentionally opened valve of cleaning tank is cause of the accident. Loss of coolant occurred in spent fuel pool of PAKS. Due to loss of coolant, spent fuels were exposed to the vapor state atmosphere, and oxidation occurred in the cladding tube of the spent fuel that rose to 1,400°C. In this study, Review of spent fuel pool accident in major foreign countries was conducted as basic studies for establishing regulatory measures and safety evaluation of spent fuel pool in Korea. Causes of each accident were different by structure of spent fuel pools. Result of this study will be contributed to establish safety measures of spent fuel pool accident suitable for domestic spent fuel pool facility.

Integrity evaluation scheme for Spent Fuel (SF) dry storage has been developed under transportation failure modes. This method especially considered the degradation characteristics of Spent Fuel (SF) during dry storage such as radial and circumferential hydride content, hydride volume fraction, oxide thickness, etc. Hydride and zircaloy cladding are considered as material composite system, using correlation models related to material properties. Critical Strain Energy Density (CSED) is compared with Strain Energy Density (SED), to evaluate cladding integrity. CSED serves as material characteristics, while SED can be considered as boundary condition. To calculate the CSED of cladding in the lateral failure mode, circumferential hydride concentration is used. SED is calculated considering both the bending moment and axial load. On the other hand, in the longitudinal failure case, fuel rod temperature, internal pressure, hoop stress, radial hydride concentration is used to calculate CSED. And pinch force (contact) was considered to evaluate SED. Model validations were conducted by comparing hot cell SF test and existing validated evaluation results. To separately handle normal transportation conditions from hypothetical accident conditions, SED according to stress-strain analysis results was separated into elastic and plastic regions. As a result of applying this scheme for 14×14 SF, failure probability of normal condition was zero, which is the similar result with DOE and same with EPRI. Regarding accident condition, lateral case showed similar result, but longitudinal case showed different but reasonable result, which was due to the different analysis conditions. The proposed methodology which was indigenously developed through this study is named as K-method.

Given the domestic situation, all nuclear power plants are located at the seaside, where interim storage sites are also likely to be located and maritime transportation is considered inevitable. Currently, Korea does not have an independently developed maritime transportation risk assessment code, and no research has been conducted to evaluate the release rate of radioactive waste from a submerged transportation cask in the sea. Therefore, secure technology is necessary to assess the impact of immersion accidents and establish a regulatory framework to assess, mitigate, and prevent maritime transportation accidents causing serious radiological consequences. The flow rate through a gap in a containment boundary should be calculated to determine the accurate release rate of radionuclides. The fluid flow through the micro-scale gap can be evaluated by combining the flow inside and outside the transportation cask. In this study, detailed computational fluid dynamic and simplified models are constructed to evaluate the internal flow in a transportation cask and to capture the flow and heat transfer around the transportation cask in the sea, respectively. In the future, fluid flow through the gap will be evaluated by coupling the models developed in this study.

In order to dispose of spent nuclear fuel (SNF) in deep geological repository, source term evaluation considering its specification, enrichment, burnup, cooling time should be performed. In this study, the measured values of Takahama-3 pressurized water reactor SNF (WH 17×17) samples were analyzed with SCALE 6.1/ORIGEN-S and TRITON code calculation results for validation. Unlike the ORIGENS code, TRITON code calculations differed from two-dimensional neutron flux distribution by using the multi-group cross-section library. Both calculation results from ORIGEN-S and TRITON code showed higher errors in 234U, 239Pu, and 241Pu compared to other actinide nuclides. In the case of axial locations of fuel rods in fuel assembly, fuel rods located at the edge of the fuel assembly presented increased errors due to nuclear reaction cross-section. Overall, the ORIGEN-S predictions informed more accurate agreement with the measured results compared with TRITON results. Especially to 235U, 239Pu, and 240Pu radionuclides, ORIGEN-S errors were denoted more than twice as low as the TRITON results. Comparing the calculation results with experimental results implied that the ORIGENS code was more accurate code than the TRITON code for source term evaluation.