The membrane structure should maintain the membrane materials in tension for structural stability guaranty. The anchoring part in the membrane structure is an important part. It has the function to introduce tension into membrane materials and function to transmit stress which membrane materials receives to boundary structure such as steel frames. In this paper, it grasps anchoring system of the anchoring part in the membrane structure concerning the fracturing characteristic condition of membrane structure, and the influence which is caused to yield it designates the stress state when breaking the membrane structure which includes the anchoring part and that stress transition mechanism is elucidated as purpose. This paper follows to previous paper, does 1 axial tensile test concerning the bolting part specimen, grasp of fracturing progress of the bolting part and the edge rope and hardness of the rubber, does the appraisal in addition with the difference of bolt tightening torque. As a result, the influence which the bolt anchoring exerts on the fracturing characteristics of the membrane material in the membrane structure anchoring part is examined.

본 연구는 현재 가설되어 가용 중인 프리스트레스트 구조물에 대해서 긴장 응력을 계측하는 방법에 관한 연구를 위해 외부 자화를 이용한 PSC 텐던의 긴장 응력 계측에 관한 연구를 진행하였다. 이에 유한요소해석을 이용하여 PSC 거더에 외부 자화 시 잔존 긴장 응 력을 검출하기 위해 PSC 거더 내부의 PS 텐던까지 영향을 줄 수 있는 코일 배치 및 크기 등을 고려하여 최적의 센서를 설계하였다. 또 한, 유한요소해석을 이용하여 설계한 센서와 동일한 수치 및 재질 데이터를 이용해 이론적 검증을 진행하였으며 타겟 위치에서 자화 의 세기를 계산하였을 때, 유한요소해석 결과와 동일한 결과를 얻어낼 수 있었다. 이를 통해 설계한 센서의 검증 및 비 접촉 외부 자화 EM 센서를 활용하여 PSC I형 거더 내부 텐던의 자화가 가능함을 확인하였다.

In this study, an AISI 316 L alloy was manufactured using a selective laser melting (SLM) process. The tensile and impact toughness properties of the SLM AISI 316 L alloy were examined. In addition, stress relieving heat treatment (650oC / 2 h) was performed on the as-built SLM alloy to investigate the effects of heat treatment on the mechanical properties. In the as-built SLM AISI 316 L alloy, cellular dendrite and molten pool structures were observed. Although the molten pool did not disappear following heat treatment, EBSD KAM analytical results confirmed that the fractions of the low- and high-angle boundaries decreased and increased, respectively. As the heat treatment was performed, the yield strength decreased, but the tensile strength and elongation increased only slightly. Impact toughness results revealed that the impact energy increased by 33.5% when heat treatment was applied. The deformation behavior of the SLM AISI 316 L alloy was also examined in relation to the microstructure through analyses of the tensile and impact fracture surfaces.

For form stability of membrane structures, membrane material is required to be in tension. Therefore, in planning and maintenance management, the engineer should consider enough about introduction of stress during construction and re-introduction of stress after completion. Clamping part is an important portion with the function for introducing tension into membrane materials, and the function to transmit stress to boundary structures, such as steel frames. Then, the purpose of this research is to clarify stress condition and stress transfer mechanism including clamping part of membrane structures, and to grasp the changing tendency of membrane structures with the passage of time. In this research, following previous one, we perform well-balanced evaluation by conducting tensile fractured tests of clamping part's specimens, and by measuring individually the amount of displacement of not only overall specimen's length but membrane material and clamping part. Thereby, we consider the influence the difference in the hardness of edge rope and the difference in the direction of thread affect modification and fracture load.

PURPOSES : Previously, airport concrete pavement was designed using only aircraft gear loading without consideration of environmental loading. In this study, a multiple-regression model was developed to predict maximum tensile stress of airport concrete pavement based on finite element analysis using both environmental and B777 aircraft gear loadings. METHODS: A finite element model of airport concrete pavement and B777 aircraft main gears were fabricated to perform finite element analysis. The geometric shape of the pavement, material properties of the layers, and the loading conditions were used as input parameters for the finite element model. The sensitivity of maximum tensile stress of a concrete slab according to the variation in each input parameter was investigated by setting the ranges of the input parameters and performing finite element analysis. Based on the sensitivity analysis results, influential factors affecting the maximum tensile stress were found to be used as independent variables of the multi regression model. The maximum tensile stresses predicted by both the multiple regression model and finite element model were compared to verify the validity of the model developed in this study. RESULTS: As a result of the finite element analysis, it was determined that the maximum tensile stress developed at the bottom of the slab edge where gear loading was applied in the case that environmental loading was small. In contrast, the maximum tensile stress developed at the top of the slab center situated between the main gears in the case that the environmental loading got larger. As a result of the sensitivity analysis and multiple regression analysis, a maximum tensile stress prediction model was developed. The independent variables used included the joint spacing, slab thickness, the equivalent linear temperature difference between the top and bottom of the slab, the maximum take-off weight of a B777 aircraft, and the composite modulus of the subgrade reaction. The model was validated by comparing the predicted maximum tensile stress to the result of the finite element analysis. CONCLUSIONS : The research shown in this paper can be utilized as a precedent study for airport concrete pavement design using environmental and aircraft gear loadings simultaneously.

In this study, tensile stresses of partially delaminated CFRP sheets were analytically evaluated. The analytical model is a 15-m long concrete beam with a rectangular cross-section of 2×3 m and uses 480 2D-plate elements and 5760 3D-solid elements for mesh construction. The elastic modulus of concrete and CFRP sheet used in the analysis are 27,536 MPa and 200,000 MPa, respectively, and the compressive strength of concrete and tensile strength of CFRP sheet are 30.0 MPa and 4,000 MPa, respectively. In order to evaluate the change of the tensile stress due to the delamination of the CFRP sheet, the whole attached model and the partially delaminated model according to the position of delamination were considered. As a result of the finite element analysis, the tensile stress of the entire attached CFRP sheet showed a constant tensile stress on the whole cross section, and the tensile stress of the partially delaminated CFRP sheet showed the maximum tensile stress on the position of delamination. Based on the results of this study, future research will be carried out to optimize the layout and shape of CFRP sheets embedded with optical fiber sensors.

Until recently, almost all ETFE film structures that have been erected is the cushion type because there are problems at lower allowable strength under elastic range and viscosity behaviour such as creep and relaxation of ETFE films under long-term stresses. But the number of tension type structures is currently increasing. This paper proposes the stretch fabrication of ETFE film to verify the applicability of ETFE films to tensile membrane structures. First of all, to investigate the possibility of application on tensile membrane structures, the stretch fabrication test is carried out, and it is verified that it is possible to increase the yield strength of the film membrane structures. After simulating the experiment also carries out an analytical investigation, and the effectiveness of the elasto-plastic analysis considering the viscous behavior of the film is investigated. Finally, post-aging tension measurement is conducted at the experimental facilities, and the viscosity behavior resulting from relaxation is investigated with respect to tensile membrane structures.

Most of the structural forms in which ETFE film is used are the cushion(pneumatic membrane structures) and tension type(tensile membrane structures), which have been generally accepted to be the most efficient forms. Tensile membrane structures are pulled outward from the exterior to introduce initial stress. And such structures offer the advantage of a natural shape formed by tensile stress and eliminate the need for blast air. Recently, the number of tension type structures is increasing. However, there are problems of creep and relaxation of ETFE films under long-term stresses. In this paper, the stretch fabrication method is proposed for stretching the film into the plastic region during initial tensioning as a way to increase its strength. And its effectiveness is confirmed by investigating experimental and analytical test using ETFE films.

막재는 매우 유연하여 압축력이 가해지면 주름이 생길 수 있다. 이러한 주름은 막재료를 재단하거나 접합하는 과정에서 생기는 제작오차, 시공오차 및 장기간의 편심하중에 의해 막재 표면에 주름이 발생할 수 있다. 본 논문에서는 막재 요소가 단축응력상태가 되어 주름을 일으키는 과정을 기술하고 주름을 체크할 수 있는 방법을 제안하였다. 막구조물에 대한 형상해석이 완료된 후 실제 하중을 적용한 응력-변형해석 시, 주응력을 계산하여 주응력 2가 0보다 작은 경우 주름이 발생한 것으로 간주되었다. 적용성을 알아보기 위해서 먼저 안장형 구조물을 해석하였고, 실제구조물인 수원야외 음악당 지붕구조에 설치된 막구조물과 1975년 오키나와 엑스포에 세워졌던 막구조물을 예제로 하여 본 논문에서 제안된 방법을 적용하여 해석해 보았다.

Periodontal ligament (PDL) tissue is a connective tissue that is interposed between the roots of the teeth and the inner wall of the alveolar bone socket. PDL is always exposed to physiologic mechanical force such as masticatory force and PDL cells play important roles during orthodontic tooth movement by synthesizing and secreting different mediators involved in bone remodeling. The Wnt/β-catenin signaling pathway was recently shown to play a significant role in the control of bone formation. In the present study, we applied cyclic tensile stress of 20% elongation to cultured human PDL cells and assessed its impact after six days upon components of the Wnt/β-catenin signaling pathway. RTPCR analysis showed that Wnt1a, Wnt3a, Wnt10b and the Wnt receptor LRP5 were down-regulated, whereas the Wnt inhibitor DKK1 was up-regulated in response to these stress conditions. In contrast, little change was detected in the mRNA expression of Wnt5a, Wnt7b, Fz1, and LRP6. By western blotting we found decreased expression of the β-catenin and p-GSK-3β proteins. Our results thus show that mechanical stress suppresses the canonical Wnt/β-catenin signaling pathway in PDL cells.

This paper investigates tensile characteristics of the stress aging heat-treated SM45C steel which are aging temperature at 250℃, 300℃, aging time at 1, 3 hours, and applied load at 300, 400N conditions by using acoustic emission. Most suitable aging condition was aging temperature 300℃, aging time 1 hour, and aging applied load 300N. And increased yield load 28.3% than non-treatment specimen in this condition. AE energy in elastic limit increased about 16.7 times than non-treatment specimen. When aging time is 3 hours, yield load decreased than other conditions that possibility is high to have itself defect on inside the specimen or coarse grain size precipitation is different in happened over-aging phenomenon. Especially, in case of 300℃, 3 hours and 400N condition appeared AE energy in elastic limit fairly high about 30 times than non-treatment specimen. This is considered by emit a lot of energies when material causes plastic deformation because the ductility increases on specimen by over-aging phenomenon.

선박용 강판(KR Grad A-3)과 라임티타니아계 피복 아아크 용접봉(E4303)을 이용하여 대기중용접 및 습식 수중 용접하여 TRC 임계응력치, 열 사이클, 경도분포, 확산성 수소량, micro조직 등을 실험적으로 조사한 결과를 요약하면 다음과 같다. 1. TRC 시험에 의한 초기 임계응력치 Σ 하(cr) 은 대기중 용접 및 수중용접의 어느 쪽에서도 Y groove 형상의 경우가 각각 71kg/mm 상(2), 51kg/mm 상(2) 로서 가장 높고, 반대로 45˚r 형 groove의 경우가 각각 52kg/mm 상(2), 41kg/mm 상(2)로서 최저이며, 수중용접부의 냉파괴 감수성이 대기중용접보다 높다. 2. 용접부의 경도는 조립 열영향부에서 가장 높고 대기중용접에서 약 H 하(k) 365, 수중용접에서는 급격한 냉각속도 때문에 약 H 상(k) 670으로 높게 되어 후자의 경우 파괴 감수성의 증가에 의한 낮은 임계응력치를 갖게 된다. 3. 48시간 동안의 확산성 수소량은 대기중용접에서 약 18cc/100g-weld-metal, 수중용접의 경우 약 48cc/100g-weld-metal로서 수중용접의 경우가 약 3배 정도 더 침입하고 있으므로 이의 방지책이 필요하다.

This feasibility study examines if the tensile stress on bonded PSC tendon could be estimated by means of measuring electrical impedance. The impedances of the five beam specimens with different tensile stress levels were measured. As tensile stress on the tendon increases, the impedance of the tendon considerably decreases. Thus, it seems that the estimation of the tensile stress on the tendon could be possible by measuring the electrical impedance.

실제 교량의 바닥판에 적용할 목적으로 섬유의 길이 및 혼입량을 달리한 두 가지 초고성능 시멘트 복합체를 고려하고 있다. 이 연구의 목적은 이 두 재료의 균열저항성을 평가하는 것이다. 두 재료에 대한 휨인장 파괴실험을 수행하였고, 실험으로부터 얻은 하중-균열개구변위 관계를 최적으로 모사하는 인장응력-균열개구 관계를 역해석을 통해 파악하였다. 역해석결과 13 mm 길이의 섬유를 2% 함유한 UHPCC는 16.3 mm와 19.5 mm 길이의 섬유를 각각 0.5%와 1.0% 함유한 UHPCC에 비해 파괴에너지가 작은 것으로 나타났다. 균열을 보다 분산시키고 균열폭을 감소시키기 위해서는 길이가 긴 두 종류의 섬유를 혼용한 UHPCC를 사용하는 것이 바람직할 것으로 판단된다.