본 연구에서는 생체모방형 비대칭 분리막 제조방법인 사각펄스양극산화법의 비대칭성 한계를 극복하기 위해 최근 보고된 셀렌산 전해액을 이용하고 표면개질에 따른 정류특성을 평가하였다. 분리막의 비대칭 원뿔형 채널은 최소직경이 10 nm이고 최대직경이 50 nm이며 길이가 5 μm이었다. 분리막의 정류특성은 기존 황산 전해액에서 제작된 것보다 높았으며 +1 V에서의 전류가 -1 V일 때보다 최대 2.9배를 나타내었다. 또한, 실란화 반응을 이용한 표면개질을 통해 술폰산기를 도입한 분리막은 반대로 -1 V에서의 전류가 +1 V일 때보다 전류의 최대 4.2배인 정류특성을 나타냈다. 실험에 대한 이론적 증명은 2D 모델에 수치해석 결과를 제시함으로써 뒷받침되었다. 본 연구의 결과는 서로 다른 정류방향을 갖는 두 종류의 이온 정류 분리막을 손쉽게 제작할 수 있는 방법을 제시하며 이온의 이동을 제어하기 위한 다양한 연구 분야에 활용될 수 있을 것으로 기대된다.

Intermetallic compound matrix composites have been expected to be established as high temperature structural components. Ni3Al is a representative intermetallic alloy, which has excellent ductility even at room temperature by adding certain alloying elements. Ni3Al matrix composites with aluminum oxide particles, which are formed by the in-situ reaction between the alloy and aluminum borate whiskers, are fabricated by a powder metallurgical method. The addition of aluminum borate whiskers disperses the synthetic aluminum oxide particles during sintering and dramatically increases the strength of the composite. The uniform dispersion of reaction synthesized aluminum oxide particles and the uniform solution of boron in the matrix seem to play an important role in the improvement in strength. There is a dramatic increase in strength with the addition of the whisker, and the maximum value is obtained at a 10 vol% addition of whisker. The Ni3Al composite with 10 vol% aluminum oxide particles 0.3 μm in size and with 0.1 wt% boron powder fabricated by the conventional powder metallurgical process does not have such high strength because of inhomogeneous distribution of aluminum oxide particles and of boron. The tensile strength of the Ni3Al with a 10 vol% aluminum borate whisker reaches more than twice the value, 930 MPa, of the parent alloy. No third phase is observed between the aluminum oxide and the matrix.

분리막(Separation membrane)을 이용하여 기체 또는 액체상태로 존재하는 분자들을 선택적으로 분리하는 기술은 화학, 생물, 제약, 석유화학 등의 산업에서 매우 다양하게 응용되고 있으며 산업적으로 매우 큰 비중을 차지하고 있다. Anodic aluminum oxide (AAO) 막은 nanochannel의 직경, nanochannel 간의 거리 및 원통형 nanochannel의 길이 등을 정밀하게 조절 할 수 있어 AAO 막을 이용하여 혼합분자를 효과적으로 분리하려는 다양한 연구가 진행되고 있다. 본 연구에서는 양 말단이 열려있어 through-hole 구조로 다양한 직경의 nanochannel을 가지는 AAO 막을 제작하였으며, 이것을 이용하여 용매에 녹아 있는 고분자 사슬의 수력학적 부피에 따른 선택적 투과를 관찰하였다. Nanochannel을 투과한 고분자 사슬의 회전반지름과 nanochannel의 직경 사이에 정량적인 관계가 있음을 확인하였다. 또한 AAO 막의 nanochannel을 흐르는 고분자 용액의 유동 률(flow rate)이 Hagen-Poiseuille 관계식으로 정확하게 설명될 수 있음을 확인하여 AAO 내에 존재하는 원통형태의 nanochannel 내에서 흐르는 용액의 나노흐름(nanoflow)에 대한 이론적 해석이 가능함을 증명하였다.

Anodic aluminum oxide (AAO) has been widely used for the development and fabrication of nano-powder with various morphologies such as particle, wire, rod, and tube. So far, many researchers have reported about shape control and fabrication of AAO films. However, they have reported on the shape control with different diameter and length of anodic aluminum oxide mainly. We present a combined mild-hard (or hard-mild) anodization to prepare shape-controlled AAO films. Two main parameters which are combination mild-hard (or hard-mild) anodization and run-time of voltage control are applied in this work. The voltages of mild and hard anodization are respectively 40 and 80 V. Anodization was conducted on the aluminum sheet in 0.3 mole oxalic acid at 4oC. AAO films with morphologies of varying interpore distance, branch-shaped pore, diameter-modulated pore and long funnel-shaped pore were fabricated. Those shapes will be able to apply to fabricate novel nano-materials with potential application which is especially a support to prevent volume expansion of inserted active materials, such as metal silicon or tin powder, in lithium ion battery. The silicon powder electrode using an AAO as a support shows outstanding cycle performance as 1003 mAh/g up to 200 cycles.

Vertically oriented nickel nanowire arrays with a different diameter and length are synthesized in porous anodic aluminium oxide templates by an electrodeposition method. The pore diameters of the templates are adjusted by controlling the anodization conditions and then they are utilized as templates to grow nickel nanowire arrays. The nickel nanowires have the average diameters of approximately 25 and 260 nm and the crystal structure, morphology and microstructure of the nanowires are systematically investigated using XRD, FE-SEM and TEM analysis. The nickel nanowire arrays show a magnetic anisotropy with the easy axis parallel to the nanowires and the coercivity and remanence enhance with decreasing a wire diameter and increasing a wire length.

투명 전도성 산화물로서 알루미늄과 붕소가 함께 도핑된 아연산화물(AZOB)이 900℃에서 분무 열분해법에 의해 제조되었다. 얻어진 마이크론 크기의 AZOB 분말은 알루미늄, 붕소 및 아연의 수용액으로부터 얻어진다. 분무 열분해로 얻어진 마이크론 크기의 AZOB 분말은 700℃에서 두 시간동안의 후 소성 과정과 24 시간 동안의 볼 밀링을 통해 나노 크기의 AZOB으로 변환된다. AZOB을 구성하는 일차 입자의 크기를 Debye-Scherrer 식에 의해 계산하였고 압축된 AZOB 펠렛의 표면 저항을 측정하였다.

Zinc oxide as an optoelectronic device material was studied to utilize its wide band gap of 3.37 eV and high exciton biding energy of 60 meV. Using anti-site nitrogen to generate p-type zinc oxide has shown a deep acceptor level and low solubility. To increase the nitrogen solubility in zinc oxide, group 13 elements (aluminum, gallium, and indium) was co-added to nitrogen. The effect of aluminum on nitrogen solubility in a 3×3×2 zinc oxide super cell containing 72 atoms was investigated using density functional theory with hybrid functionals of Heyd, Scuseria, and Ernzerhof (HSE). Aluminum and nitrogen were substituted for zinc and oxygen sites in the super cell, respectively. The band gap of the undoped super cell was calculated to be 3.36 eV from the density of states, and was in good agreement with the experimentally obtained value. Formation energies of a nitrogen molecule and nitric oxide in the zinc oxide super cell in zinc-rich conditions were lower than those in oxygen-rich conditions. When the number of nitrogen molecules near the aluminum increased from one to four in the super cell, their formation energies decreased to approach the valence band maximum to some degree. However, the acceptor level of nitrogen in zinc oxide with the co-incorporation of aluminum was still deep.

Ni nanowires were fabricated using anodic aluminum oxide (AAO) membrane as a template by electrochemical deposition. The nanowires were formed within the walls of AAO template with 200 nm in pore diameter. After researching proper voltage and temperature for electrochemical deposition, the length of Ni nanowires was controlled by deposition time and the supply of electrolyte. The morphology and microstructure of Ni nanowires were investigated by field emission scanning electron microscope (FE-SE), X-ray diffraction (XRD) and transmission electron microscope (TEM).

Transparent conducting aluminum-doped ZnO thin films were deposited using a sol-gel process. In this study, the important deposition parameters were investigated thoroughly to determine the appropriate procedures to grow large area thin films with low resistivity and high transparency at low cost for device applications. The doping concentration of aluminum was adjusted in a range from 1 to 4 mol% by controlling the precursor concentration. The annealing temperatures for the pre-heat treatment and post-heat treatment was 250˚C and 400-600˚C, respectively. The SEM images show that Al doped and undoped ZnO films were quite uniform and compact. The XRD pattern shows that the Al doped ZnO film has poorer crystallinity than the undoped films. The crystal quality of Al doped ZnO films was improved with an increase of the annealing temperature to 600˚C. Although the structure of the aluminum doped ZnO films did not have a preferred orientation along the (002) plane, these films had high transmittance (> 87%) in the visible region. The absorption edge was observed at approximately 370 nm, and the absorption wavelength showed a blue-shift with increasing doping concentration. The ZnO films annealed at 500˚C showed the lowest resistivity at 1 mol% Al doping.

Aluminum nitride (AlN) nanopowders with low degree of agglomeration and uniform particle size were synthesized by carbothermal reduction of alumina and subsequent direct nitridization. Boehmite powder was homogeneously admixed with carbon black nanopowders by ball milling. The powder mixture was treated under ammonia atmosphere to synthesize AlN powder at lour temperature. The effect of process variables such as boehmite/carbon black powder ratio, reaction temperature and reaction time on the synthesis of AlN nanopowder was investigated.

The feasibility of obtaining highly dispersed aluminum oxide powders by the electrical explosion of aluminum conductors in an inert gas atmosphere and the subsequent oxidation of aluminum particles by water prior to their contact with air is demonstrated. For a specific surface area of the initial aluminum powder of 6.5/g, the corresponding specific surface area of the resultant aluminum oxide nanopowder was as large as 300/g.

지구가 마그마 바다 상태에서 현재의 층상화된 내부 구조로 분화되는 진화과정의 체계적인 이해를 위하여 규산염 용융체와 같은 비정질 산화물의 결정화과정 메커니즘 규명이 필요하다. 이를 위하여 결정화 과정에서 수반하는 용융체의 원자구조 변화를 실험적으로 측정하여 결정화 과정을 정량적으로 정립할 수 있다. 본 연구에서는 고상 핵자기 공명 분광분석(NMR)을 이용하여 졸겔법으로 합성한 비정질 알루미나(Al2O3)의 온도-가열 시간 변화에 따른 원자구조 변화로부터, 비정질-결정질 상전이 과정을 원자 단위에서 규명하였다. 비정질 Al2O3의 27Al 3QMAS NMR 실험 결과 다량의 배위수 4, 5의 알루미늄([4,5]Al)과 소량의 배위수 6인 알루미늄([6]Al)이 명확히 구분되어 관찰되었고, 973 K와 1,073 K에서 각각 가열시간을 증가시킬수록 배위수 5인 알루미늄([5]Al)이 감소하였다. 본 연구에서는 [5]Al의 분율을 결정화의 지표로 이용하여 27Al 3QMAS NMR 결과를 정량 분석하였다. 분석을 통해 점진적인 원자구조의 변화로 관찰되는 비정질 산화물의 상전이 과정이 결정화 혹은 비정질 내 구조적 무질서도의 변화와 같은 복합적인 단계로 구성될 수 있음을 확인하였다. 이러한 연구 결과는 다양한 자연계의 다성분계 규산염 용융체 결정화 과정 및 마그마 바다의 분화와 지구의 화학적 진화에 대한 원자 단위의 이해증진에 도움을 줄 것이다.