For the regeneration of diesel particulate filters (DPF) using non-thermal plasma (NTP), both cost-effectiveness and regeneration efficiency should be raised. This study compared and contrasted the physicochemical characteristics of carbon black and engine particulate matter (PM). After carbon black was put into the DPF, an experimental setup for the oxidation of PM using NTP was created. The findings showed that carbon black and PM samples had comparable oxidation traits, micronanostructures, and C/O elemental ratios. O3, the main active species in NTP, was susceptible to heat breakdown, and the rate of decomposition of O3 increases with increasing temperature. The removal effectiveness of carbon black first improved and subsequently declined with an increase in the NTP injection flow rate during offline DPF regeneration using NTP at room temperature. A relatively high carbon black removal efficiency of 85.1% was achieved at an NTP injection flow rate of 30 L/min.

The effect of EGR on fuel economy was investigated in a gasoline direct injection engine. The 1-D cycle simulation program of GT-Power was utilized to evaluate fuel consumption rate. At high load, fuel consumption increased by about 2~6% according to EGR rate. Knock mitigation was the main effects, gaining about 80% of the total fuel consumption improvement. At low load, fuel consumption reduction was 0.6~2%, which was much lower than that for high load. The lower improvement of fuel consumption at low load is attributed to solely dilution and chemical effects of exhaust gas.

목 적 : 복부 dynamic검사 시 조영제 주입 후 환자의 이상 반응 발생 빈도 및 조영제의 신호 대 잡음비 분석을 통해 적정한 조영제 주입 속도를 알아보고자 하였다. 대상 및 방법 : 2013년 4월부터 2014년 9월까지 3.0T MRI system(Magnetom Tim Trio, Siemens, Germany)을 이용하여 Gadoxetic acid(Primovist, Bayer Schering Pharma)를 사용한 309명(남자 223명, 여자 86명)을 대상으로 Liver dynamic검사를 하였고, Gadodiamide(Ominisacn, GE healthcare)을 사용한 247명(남자 148명, 여자 99명)을 대상으로 Cholangio, Pancreas MRI 상복부 검사를 시행하였다. Saline은 주입 속도를 조영제와 동일하게 주입했으며 그 양은 30ml로 고정하고 gadoxetic acid의 양은 0.1ml/kg, 조영제의 주입속도는 1.0cc/sec, 1.5cc/sec, 2.0cc/sec로 60sec, 100sec을 측정했다. Gadodiamide의 양은 0.2ml/kg, 조영제 주입 속도는 1.5cc/sec, 2.0cc/sec, 2.5cc/sec로 60sec, 120sec을 측정했으며 Volumetric Interpolated Breath-hold Examination(VIBE) sequence를 적용하여 영상을 획득하였다. 상복부 MRI검사 시 조영제의 주입속도에 따른 이상 반응 유무 및 발생 빈도를 분석하고 획득한 영상은 PACS viewer에서 각 phase 별로 ROI를 5~15mm로 main portal vein, liver parenchyma, aorta를 세 곳 설정하여 각 부위의 SNR을 60초, 100초, 120초 검사 중심으로 정량 분석하였다. 결 과 : Liver MRI의 arterial phase 시간대 이상 반응(일시적 호흡곤란, 기침, 구토, 가슴 답답함 등) 발생 빈도는 2.0cc/sec는 98명 중 23건(23.5%), 1.5cc/sec는 116명 중 44건(37.9%), 1.0cc/sec에서 95명 중 22건(23.2%)으로 나타났다. SNR은 조영제주입 속도를 2.0cc/sec로 했을 때 60초 검사에서 portal vein 439.13±38.26, liver parenchyma 250.54±28.54, aorta 311.74±33.24였고 100초에서는 312.01±20.29, 283.88±28.60, 250.38±22.68이었다. 1.5cc/sec의 경우 60초 검사에서 portal vein 415.81±42.43, parenchyma 247.14±28.24, aorta 305.48±30.16, 100초엔 각각 339.20±32.12, 273.65±29.28, 264.66±29.84였다. 1.0cc/sec의 경우 60초 검사는 portal vein 400.44±42.43, parenchyma 237.95±28.30, aorta 307.24±33.69, 100초는 359.17±31.67, 259.13±27.90, 280.49±32.74였다. Cholangio MRI는 2.5cc/sec는 90명 중 6명(6.7%), 2.0cc/sec는 87명 중 3명(3.4%), 1.5cc/sec에서 70명 중 4명(5.7%)이 arterial phase에서 이상 반응이 발생됐다. 신호대 잡음비는 2.5cc/sec로 조영제 주입 시 60초 검사에서 portal vein 659.09±59.10, liver parenchyma 367.40±39.09, aorta 537.40±41.82였으며 120초에서 각각 546.79±40.35, 376.15±28.79, 470.59±36.99였다. 2.0cc/sec로 주입했을 땐 60초에 portal vein 648.18±61.19, parenchyma 360.49±41.35, aorta 540.07±51.77이었고 120초는 각각 559.26±52.35, 343.70±38.27, 474.57±42.02였으며 1.5cc/sec로 주입 시엔 60초에 portal vein 637.62±54.24, parenchyma 358.85±42.87, aorta 544.25±47.16였고 120초는 562.35±39.57, 303.91±40.20, 481.22±40.14이었다. 결 론 : 조영제의 주입 속도를 2.0cc/sec로 했을 경우 Liver MRI는 저속 주입 시 보다 60초와 100초 검사에서 이상 반응의 증가없이 SNR이 더 좋은 영상을 획득했다. Cholangio MRI 또한 60초와 120초 검사에서 2.5cc/sec로 주입했을 때 저속 주입 시 보다 SNR이 더 우수한 영상을 얻을 수 있었다.

Injection rate characteristics of biodesel fuels according to the blending ratio was described in this work. The injection rate measuring system based on the Bosch's method was utilized to measure and compare the fuel injection rate characteristics. Three different types of biodiesel which were derived from seed, unpolished-rice, and soybean were blended with the diesel fuel in 20% and 40% of volumetric ratio. The fuel properties, injection mass, and injection rate characteristics were obtained and compared in various injection conditions. It is expected that this observations provide important insights into the effect of fuel properties on the biodiesel fuel injection rate performance in a CI engine

ICSI시 동결 융해한 부고환 정자의 이용 가능성을 알아보고자 난자의 배양시 체외성숙율과 활성화 처리를 한 난자와 동결 융해한 부고환 정자로 ICSI시 체외발생율을 조사하였으며, 결과를 요약하면 다음과 같다. 1. 난포란을 회수 후 24시간 배양하였을 때 배양 시간에 따른 GV, MI, M II로의 체외성숙율은 각각 7/60(11.7%), 5/60(8.3%), 48/60(80.0%)였고 30시간 배양 시간에 따른 GV, MI, M II로의 체외성숙율은

사염화우라늄을 제조하기 위한 가장 효율적인 반응계는 이산화우라늄, 염소가스와 탄소분말이다. 여러 가지 실험변수 가운데 이산화우라늄의 염소화반응에 사용된 염소가스 주입량과 탄소의 양이 사염화우라늄 제조에 미치는 영향에 관하여 연구하였다. 각각의 실험변수들에 대한 전화율과 휘발률 계산을 통해 효율적인 반응을 위한 적정 염소가스 주입량과 탄소의 양을 구하였고, 이산화우라늄의 증가함에 따라 직접접촉에 의한 기체-고체반응에서는 전화율과 휘발률은 증가했으나 이후 과량을 첨가함에 따라 감소하였고, 용융염내의 기체-액체반응에서는 전화율의 미미한 증가와 휘발률의 감소를 확인하였가. 염소주입량이 증가함에 따라 전화율과 휘발률이 증가했으며, 과량의 염소가수 주입시 고이온가 염화물의 생성량이 증가하였다.

Bosch법과 Zeuch법의 분사율 측정기를 직접설계, 제작하여 분사율 측정실험을 행한 결과 다음과 같은 결론을 얻었다. 1. Bosch법 분사율 측정기는 분사량의 참 값에 대한 측정오차가 약 ±1%로 정밀도와 신뢰성이 높았다. 2. Bosch법 분사율 측정기에서, 분사율은 연료펌프의 회전수와 부하가 증가할수록 높아지는 반면, 분사기간(ms)은 회전수가 증가할수록 짧아짐을 알 수 있었다. 3. 본 실험에서는, 동일조건하의 단발분사가 연발분사에 비해 전체적으로 분사율이 낮고 기관의 1 cycle당 분사량도 약 30% 정도 적었다. 4. Zeuch법 분사율 측정기로 구한 체적강성계수의 값은 배압이 증가할수록 증가함을 알 수 있었다. 5. Zeuch법 분사율 측정기는 Bosch법 분사율 측정기에 비해 정밀도가 낮았다.

In this study, the behavior of fresh water body between the injection and production wells with the fresh water injection rate in a saline aquifer is numerically analyzed by using a three-dimensional numerical model. 8 injection wells are arranged at equidistant intervals on a concentric circle and one production well is located at the center of this circle. In the case that the fresh water injection rate is relatively small, the fresh water body around a injection well screen is not mixed with neighboring ones and is independently distributed. However, when the injection rate is increased, the size of the fresh water body is continuously increased, and the areas, where saline and fresh water among injection wells are mixed, are appeared. The mixed degree is increased as the injection rate is increased. This phenomenon is identically generated around the production well. Moreover, when the injection rate is increased, the ratio of saline water in and around the production well is decreased.

This study has been carried out to investigate Electrostatic Precipitator`s(ESP) performance enhancement and removal efficiency of fine particle according to (NH_4)_2SO_4 injection rate. The following conclusions are derived from the these test results : 1)For plant condition cases, according to the variation of concentration agent [(NH_4)_2SO_4] - 10ppm, 20ppm, 30ppm, 40ppm - ESP`s collection efficiency was increased to 97.74%, 98.95%, 99.04%, 99.47%, when inlet dust loading was 2g/㎥. And when inlet dust loading was 3g/㎥, that was increased to 98.19%, 99.16%, 99.23%, 99.58%. 2)It is seen from this experiments that the increasing 30ppm concentration of (NH_4)_2SO_4 increase the collection efficiency and fine particle emission control.

The reaction rate, equilibrium, and flow injection analysis methods were fundamentally evaluated for the determination of aqueous ammonia. The selected indophenol blue method was based on the formation of indophenol blue in which ammonium ion reacted with hypochlorite and phenol in alkaline solution. In the optimized reaction condition, the reaction followed 1st order reaction kinetics and the final product was stable. The absorbance measurements before and after the equilibrium were utilized for the reaction rate and equilibrium methods. The reaction rate methods, based on the relative analytical signals for the possibility of eliminating interferents, were shown to have good linear calibration curves but the detection limit and the calibration sensitivity were poorer than those in the equilibrium method. The detection limits were 32-49 ppb and 24 ppb for the reaction rate and equilibrium methods, respectively. In the flow injection analysis, the absorbance was measured before the equilibrium reached and thus resulted in 30% reduction of calibration sensitivity. However, the detection limit was 11 ppb, indicating that the peak-to-peak noise for the blank was remarkably improved. Compared to the manual methods, the optimized experimental condition in a closed reaction system reduced the blank absorbance and the inclusion of ammonia from the atmosphere was prevented. In addition, highly reproducible mixing of sample and reagents and analytical data extracted from continuous recording showed excellent reproducibility.