The purpose of this paper is to evaluate the structural performance of joints between modules with steel plate press forming type non-symmetric cross section. The main experimental variables are direction of load, whether vertical bolts are fastened, and whether the concrete inside the column is filled. A total of three experiments were performed for each variable. Experimental results show that the behavior of the joints dominated by the local buckling deformation of the upper and lower beam flanges of the module joints, and the final failure was the fracture of the column-beam welds. In case of short side direction, it is possible to secure the performance of intermediate moment frame (0.02 rad). In case of long side direction, it is evaluated that the performance of special moment frame (0.04 rad) is secured regardless of whether or not concrete is infilled in the column.

The chassis frame generally consists of side members, cross beams, and several mounting brackets. Strength and fatigue behaviors of welded joints between members and brackets in a frame are a very complex phenomena, which comes basically due to the structural geometry, non-homogeneous material, and welding residual stresses. Therefore, the prediction of fatigue life for the welded structure is very difficult compared to that for the simple geometry. This paper presents the structural and fatigue analysis results for a body frame and welded joints under system durability loads. In order to fatigue assessment of welded joints, local stress approach is used for its simplicity, which is based on the several empirical S-N curves that are associated with welded joint types and loading modes. The estimated fatigue cycles of the welded areas in a frame were satisfied the target cycles under system load conditions.

In this study, the structural analysis for bellows joint of high-performance that can enhance the performance of seismic isolation piping was performed. Bellows joint is that the corrugated flexible piping is connected at the both sides of elbow. An one axis of the bellows joint fixed, and the other end of the axis changes the position from 0° to 315° for the radius displacement of 500 mm. Results obtained are as follows for this case in analysing of the maximum stress and plastic strain of the bellows joint. As the location of the base isolation displacement get farther from the fixed pipe, the bellows joint is pulled, and the maximum stress and plastic deformation is increased. And so the maximum stress occurs near the bellows at both ends of the elbow. Displacement in the 135° position, a maximum stress of 837 MPa and a plastic strain of 3.00% was the highest.

프리캐스트 콘크리트 세그먼트 공법은 품질관리가 용이하고 비용 및 공사기간을 단축할 수 있으나 각 세그먼트의 조립으로 인한 접합부의 응력집중 및 큰 변위로 인해 구조적으로 불리한 거동을 보여 많은 장점에도 불구하고 폭넓은 적용에 있어 그 한계가 발생한다. 이에 본 연구에서는 구조 성능이 개선된 프리캐스트 세그먼트 접합부를 제안하고 실험을 통하여 균열 및 파괴양상, 변형률, 최대하중, 변위 연성도의 측면에서 제안한 접합부의 구조 성능을 평가하고자 하였다. 본 연구에서는 시공성 및 구조성능을 고려하여 전단키 및 포스트텐션, 강봉 등의 적용여부를 변수로 한 접합부를 제안하고 이에 대해 정적 재하 실험을 수행하였다. 실험 결과, 전단키 및 포스트텐션을 적용한 SGSP 실험체는 최대하중의 측면에서 일체형 실험체에 비해 약 86%에 준하는 내력을 보였으며 연성 측면에서는 일체형 실험체의 연성 능력 이상의 연성거동을 보임으로써 제안한 접합부의 개선된 구조성능 및 적용 가능성을 확인할 수 있었다.

이 논문은 고강도 콘크리트를 사용한 철근콘크리트 외부 보-기둥 접합부의 실험결과를 보고한 것이다. 실험체의 주요 실험변수는 접합부 파괴모드, 콘크리트 압축강도, 철근의 정착 방법이다. 모든 실험체는 ACI 352R-02 기준에 바탕을 두어 J파괴와 BJ파괴가 되도록 계획하였다. 주철근은 90도 표준갈고리로 하거나 확대머리철근으로 하였다. 실험결과는 콘크리트 압축강도에 제한되는 현행 ACI 설계 기준식이 고강도 콘크리트를 사용한 보-기둥 접합부의 강도를 다소 과소평가하고 있음을 보여준다. 또한 확대머리철근을 가진 J파괴형 보-기둥 접합부의 강도는 표준갈고리를 가진 접합부보다 약 10% 이상 높게 평가되었다.

This study is to introduce a structural analysis method that can apply a unit modular system to a remodeling extension. The structural analysis process, which can reflect the behaviors between the existing building and the modular system, is performed in a five-staged structural analysis. Therefore, the example of structural analysis of an existing building is introduced.

This study is to establish a structural analysis method that can apply a unit modular system to a remodeling extension. Structural design has to be performed after considering the behaviors between the existing structures and the modular system because the modular system is added after the transformation of existing structures has been processed. The structural analysis process, which can reflect the behaviors between the existing building and the modular system, is introduced in a five-staged structural analysis.

In this study, experimental research was carried out to evaluate the structural performance of high strength R/C interior beam-column joints regions, with or without the shear reinforcement. Specimens designed by the interior beam-column joint regions without the shear reinforcement of existing reinforced concrete building showed a unstable mode of failure and an decrease in load-carrying capacity and energy dissipation capacity and ductility ratio.

In this study, experimental research was carried out to improve the structural performance of reinforced concrete beam-column joint using high performance FRP materials in existing reinforced concrete building. Test result shows that retrofitting specimen(LBCJ-CRU, CRS, CRUS) designed by the improvement of seismic performance of reinforced concrete beam-column joints load-carrying capacities were increased 1.30~1.54 times in comparison with the standard specimen.